Apta (Draft) Specification For: 30-ft, 35-ft, 40-ft, 45-ft, 60-foot (articulated) Transit Buses
Download 0.56 Mb.
|
- Navigate this page:
- 78.3Turn signals
- 78.4Headlights
- 78.5Brake lights
- 78.6License plate lighting
- IP 79.General requirements
- IP 80.Interior panels
78.2Doorway lightingLamps at the front and rear passenger doorways shall comply with ADA requirements and shall activate only when the doors open. These lamps shall illuminate the street surface to a level of no less than 1 foot-candle for a distance of 3 ft outward from the outboard edge of the door threshold. The lights may be positioned above or below the lower daylight opening of the windows and shall be shielded to protect passengers’ eyes from glare. 78.3Turn signalsDefault Standard turn signals Turn-signal lights shall be provided on the front, rear, curb and street sides of the bus in accordance with FMVSS 108 and Part 393, Subpart B of the FMCSA as applicable. Alternative
Front turn signals shall be of wrap-around design or shall be designed to be visible from the front and the near side of the bus. 78.4HeadlightsRoved headlamps shall be designed for replacement without removing the headlamp bezel. Default
Standard installation Standard OEM headlight installation shall be provided in accordance with FMVSS 108 and Part 393, Subpart B of the FMCSA as applicable. Alternative
Headlamps shall incorporate a daytime running light feature. Alternative
Headlamps shall be LED/halogen, sealed beam. Alternative
Default
No high/center mount brake lamp or deceleration warning lamps Bus shall not include a high/center mount brake lamp and/or deceleration warning indicator lamps. Alternative
Bus shall include red, high and center mount brake lamp(s) along the backside of the bus in addition to the lower brake lamps required under FMVSS 108. The high and center mount brake lamp(s) shall illuminate steady with brake application. [Agency to specify the size of the high and center mount brake lamp(s).] Alternative
Bus shall include amber high and center mount lamp(s) along the backside of the bus that illuminate steady when the transmission is in forward mode and when the throttle is completely released (0 percent engagement). The amber lamps shall automatically extinguish, regardless of transmission and throttle condition, with brake application. Operation of the amber lamps shall be programmable with the multiplex system. [Agency to specify the size of the high and center mount, amber lamp(s).] 78.6License plate lightingThe rear license plate provision shall be illuminated per SAE J587. 78.7Service area lighting (interior and exterior)LED lamps shall be provided in the engine and all other compartments where service may be required to generally illuminate the area for night emergency repairs or adjustments. These service areas shall include, but not be limited to, the engine compartment, the communication box, junction/apparatus panels and passenger door operator compartments. Lighting shall be adequate to light the space of the service areas to levels needed to complete typical emergency repairs and adjustments. The service area lamps shall be suitable for the environment in which they are mounted. Engine compartment lamps shall be controlled by a switch mounted near the rear start controls. All other service area lamps shall be controlled by switches mounted on or convenient to the lamp assemblies. Power to the service area lighting shall be programmable. Power shall latch on with activation of the switch and shall be automatically discontinued (timed out) after 30 minutes to prevent damage caused by inadvertently leaving the service area lighting switch in the on position after repairs are made. INTERIOR PANELS AND FINISHES IP 79.General requirementsMaterials shall be selected on the basis of maintenance, durability, appearance, safety, flammability and tactile qualities. Materials shall be strong enough to resist everyday abuse and be vandalism and corrosion resistant. Trim and attachment details shall be kept simple and unobtrusive. Interior trim shall be secured to avoid resonant vibrations under normal operational conditions. Interior surfaces more than 10 in. below the lower edge of the side windows or windshield shall be shaped so that objects placed on them fall to the floor when the coach is parked on a level surface. Any components and other electrical components within close proximity to these surfaces shall also be resistant to this cleaning method. Default
Default
Interior panel required to meet FMVSS 302 Alternative Fire resistance Materials shall comply with the Recommended Fire Safety Practices defined in FTA Docket 90-A, dated October 20, 1993. Directory: swc swc -> Packet Tracer Configure Initial Router Settings (Instructor Version) Instructor Note swc -> Chapter 50 Aircraft swc -> Conservation Security Program swc -> Click on enter the exhibition swc -> Southwest Christian – Tinley Park Invitational Meet Boys Cross Country Race Friday, September 30, 2016 Cool and Cloudy – 60 Degrees swc -> Date: October 28 – December 5, 2003 Project Website swc -> Publication and presentation log swc -> Ncdmf chpp chapter Shell bottom Ecological Role and Functions Ecosystem enhancement swc -> Directions: use the map in Download 0.56 Mb. Share with your friends:
|