Intent of specifications

WALL CABINET

The cabinet(s) shall have vertically hinged door(s) constructed of the same material as the cabinet. The door(s) shall be mounted to a continuous hinge on one edge of the cabinet.  Each door shall have a slam latch preventing the door from opening when not in use.

There shall be one (1) cabinet(s) located to the left of the bench seat on the passenger side of the interior.

DRAWER ASSEMBLY

The clear dimensions of the top cabinet drawer shall be 12.25" high x 21.00" deep. Mounted below the top drawer shall be the second drawer. The clear dimensions of the second cabinet drawer shall be 4.25" high x 21.00" deep. Below the second drawer shall be the third drawer. The clear dimensions of the third cabinet drawer shall be 2.25" high x 21.00" deep. All drawers shall be the same width, and not exceed 24.00".

The drawers shall be mounted in a cabinet housing constructed of light gray powder coated aluminum with anodized aluminum frames.  The housing shall be 24.00" deep, and completely enclose the drawers.

A full-length aluminum extruded rail shall be provided at the top edge of each drawer. This rail shall act as the latching mechanism as well as the handle for each drawer.

When space permits the cabinet(s) shall be provided with a radius edge. The edging shall provide a uniform finished interior appearance.

The cabinet(s) shall be located Under the drivers side cab desk for a total quantity of one (1) in the body interior.

SLIDE-OUT MODULE

There shall be a one (1) slide-out module(s) above the drivers side exterior compartments.  The finished slide-out module interior width shall be 84.00" (2134 mm) .  The body height selected shall determine the unfinished interior height of the module. The module shall extend 30.00" (762 mm) from the body.

The slide-out module shall be operable with an interior or exterior control.  The interior control shall have a lockout feature.  The lockout feature shall prevent operation of the exterior control while someone is inside the body.  The slide-out module control shall be tied to the parking brake.  Only allowing the module to operate while the parking brake is engaged.

There shall be one (1) 4.00" (102 mm) red LED warning light installed on each side of the exterior of the slide-out module.  The light shall be automatically enabled when the module is in the extended position.

The slide-out module shall extend and retract using two (2) hydraulic cylinders.  The cylinders shall be connected to provide a uniform seal when the module is extended or retracted.

The slide-out module shall utilize three (3) seals in the extended and retracted positions for a weatherproof seal.

AWNING MOUNTING ENCLOSURE

There shall be one (1) enclosure(s) provided to mount the awning(s) above the body roof. The enclosure(s) shall be located passenger side.

The enclosure(s) shall follow the contour of the body roof line providing a clean integral appearance. There shall be a full length aluminum treadplate access cover provided creating a top of the enclosure.  The remaining portion of the enclosure shall be finished to match the body exterior paint color.

AWNING

A roll-up style awning made of a fire retardant type material shall be supplied.  The awning shall be stored in a metal housing on the side of the body when not in use.  When fully extended, the awning shall be self supported without the use of poles extending to the ground.  Lift handles shall be provided for leverage to raise the awning.  A slider bar shall be provided to raise the arms out of the way for a clear path when walking under the awning.

The awning shall be the full length of the body.  The awning shall extend out approximately (8) eight feet from the body.  The color shall be tan.

The awning shall be installed passenger side.

A total of one (1) shall be supplied.

ROOF ACCESS LADDER

A roof access ladder shall be provided at the rear of the body on the Drivers rear side.  The ladder handrails shall be constructed out of 1.25" (3 mm) heavy-walled aluminum tubing that is covered with a black, heat-resistant, powder coated finish.  Each step shall have a flat non-skid surface that is 3.00" (76 mm) deep x 15.50" (394 mm) wide.  A swing-out and down extension section at the bottom of the ladder shall be provided.

SHELVING

Compartment D1 and P1 shall include 62.00" deep shelving.

The construction shall consist of .188" thick aluminum formed to provide a 2.00" high wall around the perimeter.

The corners shall be welded to provide a rigid unit.

The shelving shall be secured within the compartment, by means of adjustable threaded fasteners.  These fasteners shall slide in an extruded aluminum track, to provide height adjustment.

There shall be six (6) provided.

ONE WAY UTILITY TRAY

A 110.00" slide-out utility type tray shall be provided in the rear compartment.

The capacity rating shall be 500 pounds minimum in the extended position.

Interior tray dimensions shall be approximately 110.00" long x 3.00" deep.

Tray shall slide out in one (1) direction only; two-thirds of its length.

The construction shall consist of .188" thick aluminum for the tray bottom and end, and special aluminum extrusions for the tray sides, front, and tracks.

Corners shall be welded to form a rigid unit.

Tray shall be supported with a minimum of six (6) ball bearing rollers; each rated for a minimum 500 pound load.

Automatic locks shall be provided for both the in and out tray positions.

There shall be one (1) provided.

R1.

Directory: NAT
NAT -> This is a working version not a completed document nato order of battle
NAT -> Supplementary Methods
NAT -> The New York Times Magazine, August 26, 2007 In Nature’s Casino
NAT -> Hurricanes are getting fiercer
NAT -> -
NAT -> April 9, 2008 Hurricanes (Continued)
NAT -> Homework 8: Hurricane Damage and Hurricane Forecasts
NAT -> Hurricane Katrina
NAT -> The United States National Report

Download 263.9 Kb.

Share with your friends: