My Wilink 8 Part Serial Output on Boot-up

My Wilink 8 Part

Serial Output on Boot-up:

U-Boot SPL 2013.01.01-g58b3988 (May 31 2013 - 10:39:50)

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Peripheral mode controller at 47401000 using PIO, IRQ 0

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Host mode controller at 47401800 using PIO, IRQ 0

OMAP SD/MMC: 0

reading u-boot.img

reading u-boot.img

U-Boot 2013.01.01-g58b3988 (May 31 2013 - 10:39:50)

I2C: ready

DRAM: 512 MiB

WARNING: Caches not enabled

NAND: 256 MiB

MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1

*** Warning - bad CRC, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Peripheral mode controller at 47401000 using PIO, IRQ 0

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Host mode controller at 47401800 using PIO, IRQ 0

Net: not set. Validating first E-fuse MAC

cpsw, usb_ether

Hit any key to stop autoboot: 0

mmc0 is current device

SD/MMC found on device 0

reading uEnv.txt

226 bytes read in 4 ms (54.7 KiB/s)

Loaded environment from uEnv.txt

Importing environment from mmc ...

Running uenvcmd ..

reading uImage

4178904 bytes read in 465 ms (8.6 MiB/s)

## Booting kernel from Legacy Image at 81000000 ...

Image Name: Linux-3.2.0-00243-g67c4111

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 4178840 Bytes = 4 MiB

Load Address: 80008000

Entry Point: 80008000

Verifying Checksum ... OK

Loading Kernel Image ... OK

OK

Starting kernel ...

[ 0.000000] Linux version 3.2.0-00243-g67c4111 (naveen@Dta0272791ub) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 Tue Jun 18 14:21:56 CDT 2013

[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine: am335xevm

[ 0.000000] Memory policy: ECC disabled, Data cache writeback

[ 0.000000] AM335X ES1.0 (sgx neon )

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048

[ 0.000000] Kernel command line: console=ttyO0,115200n8 androidboot.console=ttyO0 mem=512M root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait rootdelay=1 init=/init ip=off

[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] Memory: 512MB = 512MB total

[ 0.000000] Memory: 509880k/509880k available, 14408k reserved, 0K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)

[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)

[ 0.000000] .text : 0xc0008000 - 0xc078a000 (7688 kB)

[ 0.000000] .init : 0xc078a000 - 0xc07e0000 ( 344 kB)

[ 0.000000] .data : 0xc07e0000 - 0xc084ba70 ( 431 kB)

[ 0.000000] .bss : 0xc084ba94 - 0xc09a3890 (1376 kB)

[ 0.000000] NR_IRQS:396

[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts

[ 0.000000] Total of 128 interrupts on 1 active controller

[ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz

[ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz

[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms

[ 0.000000] Console: colour dummy device 80x30

[ 0.000152] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144)

[ 0.058929] pid_max: default: 32768 minimum: 301

[ 0.059082] Security Framework initialized

[ 0.059173] Mount-cache hash table entries: 512

[ 0.059600] CPU: Testing write buffer coherency: ok

[ 0.059661] ftrace: allocating 22068 entries in 65 pages

[ 0.128967] omap_hwmod: pruss: failed to hardreset

[ 0.129821] print_constraints: dummy:

[ 0.130035] NET: Registered protocol family 16

[ 0.131195] OMAP GPIO hardware version 0.1

[ 0.132293] omap_mux_init: Add partition: #1: core, flags: 0

[ 0.133392] omap_i2c.1: alias fck already exists

[ 0.133941] omap2_mcspi.1: alias fck already exists

[ 0.134033] omap2_mcspi.2: alias fck already exists

[ 0.134185] edma.0: alias fck already exists

[ 0.134216] edma.0: alias fck already exists

[ 0.134246] edma.0: alias fck already exists

[ 0.144592] bio: create slab at 0

[ 0.145599] SCSI subsystem initialized

[ 0.146453] usbcore: registered new interface driver usbfs

[ 0.146575] usbcore: registered new interface driver hub

[ 0.146728] usbcore: registered new device driver usb

[ 0.147033] registerd cppi-dma Intr @ IRQ 17

[ 0.147033] Cppi41 Init Done Qmgr-base(e087a000) dma-base(e0878000)

[ 0.147064] Cppi41 Init Done

[ 0.147094] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3

[ 0.147247] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1

[ 0.147705] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz

[ 0.148986] tps65910 1-002d: JTAGREVNUM 0x0

[ 0.151184] print_constraints: VRTC:

[ 0.152557] print_constraints: VIO: at 1800 mV

[ 0.154754] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal

[ 0.156951] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal

[ 0.157867] print_constraints: VDD3: 5000 mV

[ 0.159179] print_constraints: VDIG1: at 1800 mV

[ 0.160552] print_constraints: VDIG2: at 1800 mV

[ 0.161865] print_constraints: VPLL: at 1800 mV

[ 0.163208] print_constraints: VDAC: at 1800 mV

[ 0.164520] print_constraints: VAUX1: at 1800 mV

[ 0.165863] print_constraints: VAUX2: at 3300 mV

[ 0.167205] print_constraints: VAUX33: at 3300 mV

[ 0.168548] print_constraints: VMMC: at 3300 mV

[ 0.168853] tps65910 1-002d: No interrupt support, no core IRQ

[ 0.169433] Advanced Linux Sound Architecture Driver Version 1.0.24.

[ 0.170074] Bluetooth: Core ver 2.16

[ 0.170135] NET: Registered protocol family 31

[ 0.170166] Bluetooth: HCI device and connection manager initialized

[ 0.170166] Bluetooth: HCI socket layer initialized

[ 0.170196] Bluetooth: L2CAP socket layer initialized

[ 0.170227] Bluetooth: SCO socket layer initialized

[ 0.170410] Switching to clocksource gp timer

[ 0.188934] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)

[ 0.189147] musb-hdrc musb-hdrc.0: dma type: dma-cppi41

[ 0.189331] MUSB0 controller's USBSS revision = 4ea20800

[ 0.190216] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using DMA, IRQ 18

[ 0.190551] musb-hdrc musb-hdrc.1: dma type: dma-cppi41

[ 0.190734] MUSB1 controller's USBSS revision = 4ea20800

[ 0.191192] musb-hdrc musb-hdrc.1: MUSB HDRC host driver

[ 0.191284] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1

[ 0.191436] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[ 0.191467] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 0.191467] usb usb1: Product: MUSB HDRC host driver

[ 0.191467] usb usb1: Manufacturer: Linux 3.2.0-00243-g67c4111 musb-hcd

[ 0.191497] usb usb1: SerialNumber: musb-hdrc.1

[ 0.192016] hub 1-0:1.0: USB hub found

[ 0.192047] hub 1-0:1.0: 1 port detected

[ 0.192474] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using DMA, IRQ 19

[ 0.192871] NET: Registered protocol family 2

[ 0.193084] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.193481] TCP established hash table entries: 16384 (order: 5, 131072 bytes)

[ 0.193786] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)

[ 0.193969] TCP: Hash tables configured (established 16384 bind 16384)

[ 0.193969] TCP reno registered

[ 0.193969] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.194000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.194244] NET: Registered protocol family 1

[ 0.194519] RPC: Registered named UNIX socket transport module.

[ 0.194549] RPC: Registered udp transport module.

[ 0.194549] RPC: Registered tcp transport module.

[ 0.194549] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.194824] NetWinder Floating Point Emulator V0.97 (double precision)

[ 0.321472] ashmem: initialized

[ 0.321777] VFS: Disk quotas dquot_6.5.2

[ 0.321838] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[ 0.322723] fuse init (API version 7.17)

[ 0.322967] msgmni has been set to 995

[ 0.324096] io scheduler noop registered

[ 0.324096] io scheduler deadline registered

[ 0.324157] io scheduler cfq registered (default)

[ 0.326843] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0

[ 1.005981] console [ttyO0] enabled

[ 1.010040] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1

[ 1.017730] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2

[ 1.025390] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3

[ 1.033081] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4

[ 1.040710] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5

[ 1.048522] [drm] Initialized drm 1.1.0 20060810

[ 1.059417] brd: module loaded

[ 1.065765] loop: module loaded

[ 1.069213] i2c-core: driver [tsl2550] using legacy suspend method

[ 1.075714] i2c-core: driver [tsl2550] using legacy resume method

[ 1.082153] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write

[ 1.096069] Detected a daughter card on AM335x EVM..

[ 1.101074] CPLD version: CPLD1.0F

[ 1.104949] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write

[ 1.120117] Board name: A33515BB

[ 1.123504] Board version: 1.4A

[ 1.126770] SKU: SKU#01

[ 1.129852] The board is general purpose EVM in profile 0

[ 1.136322] da8xx_lcdc.0: alias fck already exists

[ 1.141693] da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel

[ 1.161804] omap-gpmc omap-gpmc: GPMC revision 6.0

[ 1.166809] Registering NAND on CS0

[ 1.170867] omap_i2c.2: alias fck already exists

[ 1.176025] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz

[ 1.182159] tsl2550 2-0039: standard operating mode

[ 1.188110] tsl2550 2-0039: registering lightsensor-level input device

[ 1.195220] input: lightsensor-level as /devices/virtual/input/input0

[ 1.201995] tsl2550 2-0039: support ver. 1.2 enabled

[ 1.207611] davinci-mcasp.1: alias fck already exists

[ 1.213226] davinci-mcasp.0: alias fck already exists

[ 1.218902] omap_hsmmc.0: alias fck already exists

[ 1.224151] omap_hsmmc.2: alias fck already exists

[ 1.252990] _regulator_get: 2-0018 supply Vdd not found, using dummy regulator

[ 1.260589] _regulator_get: 2-0018 supply Vdd_IO not found, using dummy regulator

[ 1.289184] lis3lv02d: 8 bits 3DLH sensor found

[ 1.381317] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input1

[ 1.391204] NFC Driver for TI WiLink

[ 1.395660] mtdoops: mtd device (mtddev=name/number) must be supplied

[ 1.402893] omap2-nand driver initializing

[ 1.407501] ONFI flash detected

[ 1.410888] ONFI param page 0 valid

[ 1.414550] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)

[ 1.423400] Creating 8 MTD partitions on "omap2-nand.0":

[ 1.428955] 0x000000000000-0x000000020000 : "SPL"

[ 1.434906] 0x000000020000-0x000000040000 : "SPL.backup1"

[ 1.441497] 0x000000040000-0x000000060000 : "SPL.backup2"

[ 1.447998] 0x000000060000-0x000000080000 : "SPL.backup3"

[ 1.454559] 0x000000080000-0x000000260000 : "U-Boot"

[ 1.461395] 0x000000260000-0x000000280000 : "U-Boot Env"

[ 1.467864] 0x000000280000-0x000000780000 : "Kernel"

[ 1.475982] 0x000000780000-0x000010000000 : "File System"

[ 1.585571] OneNAND driver initializing

[ 1.590209] CAN device driver interface

[ 1.594238] CAN bus driver for Bosch D_CAN controller 1.0

[ 1.641082] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6

[ 1.647552] davinci_mdio davinci_mdio.0: detected phy mask fffffffe

[ 1.655151] davinci_mdio.0: probed

[ 1.658691] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown

[ 1.666137] PPP generic driver version 2.4.2

[ 1.670776] PPP BSD Compression module registered

[ 1.675689] PPP Deflate Compression module registered

[ 1.681121] usbcore: registered new interface driver cdc_ether

[ 1.687255] usbcore: registered new interface driver cdc_eem

[ 1.693237] usbcore: registered new interface driver dm9601

[ 1.699096] usbcore: registered new interface driver cdc_subset

[ 1.705322] cdc_ncm: 04-Aug-2011

[ 1.708740] usbcore: registered new interface driver cdc_ncm

[ 1.714752] usbcore: registered new interface driver cdc_acm

[ 1.720642] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters

[ 1.729003] Initializing USB Mass Storage driver...

[ 1.734222] usbcore: registered new interface driver usb-storage

[ 1.740509] USB Mass Storage support registered.

[ 1.745513] usbcore: registered new interface driver usbserial

[ 1.751647] USB Serial support registered for generic

[ 1.756988] usbcore: registered new interface driver usbserial_generic

[ 1.763824] usbserial: USB Serial Driver core

[ 1.768402] USB Serial support registered for GSM modem (1-port)

[ 1.774841] usbcore: registered new interface driver option

[ 1.780639] option: v0.7.2:USB Driver for GSM modems

[ 1.787597] gadget: Mass Storage Function, version: 2009/09/11

[ 1.793823] gadget: Number of LUNs=1

[ 1.797637] lun0: LUN: removable file: (no medium)

[ 1.803009] gadget: android_usb ready

[ 1.806915] musb-hdrc musb-hdrc.0: MUSB HDRC host driver

[ 1.812561] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2

[ 1.820404] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002

[ 1.827514] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 1.835052] usb usb2: Product: MUSB HDRC host driver

[ 1.840240] usb usb2: Manufacturer: Linux 3.2.0-00243-g67c4111 musb-hcd

[ 1.847137] usb usb2: SerialNumber: musb-hdrc.0

[ 1.852416] hub 2-0:1.0: USB hub found

[ 1.856323] hub 2-0:1.0: 1 port detected

[ 1.861175] mousedev: PS/2 mouse device common for all mice

[ 1.867858] input: matrix-keypad as /devices/platform/matrix-keypad/input/input2

[ 1.876586] input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input3

[ 1.885192] using rtc device, am33xx-rtc, for alarms

[ 1.890258] omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0

[ 1.897521] i2c /dev entries driver

[ 1.901519] Linux video capture interface: v2.00

[ 1.906677] usbcore: registered new interface driver uvcvideo

[ 1.912689] USB Video Class driver (1.1.1)

[ 1.917877] input: lm75-temp as /devices/virtual/input/input4

[ 1.924285] lm75 2-0048: hwmon0: sensor 'tmp275'

[ 1.931762] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec

[ 1.938293] device-mapper: uevent: version 1.0.3

[ 1.943359] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com

[ 1.952178] Bluetooth: HCI UART driver ver 2.2

[ 1.956817] Bluetooth: HCI H4 protocol initialized

[ 1.961822] Bluetooth: HCILL protocol initialized

[ 1.966735] Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0

[ 1.975769] cpuidle: using governor ladder

[ 1.980194] cpuidle: using governor menu

[ 1.988098] usbcore: registered new interface driver usbhid

[ 1.993988] usbhid: USB HID core driver

[ 2.103576] logger: created 256K log 'log_main'

[ 2.108398] logger: created 256K log 'log_events'

[ 2.113464] logger: created 256K log 'log_radio'

[ 2.118377] logger: created 256K log 'log_system'

[ 2.123901] tiadc tiadc: attached adc driver

[ 2.128784] usbcore: registered new interface driver snd-usb-audio

[ 2.136627] _regulator_get: 2-001b supply IOVDD not found, using dummy regulator

[ 2.144470] _regulator_get: 2-001b supply DVDD not found, using dummy regulator

[ 2.152160] _regulator_get: 2-001b supply AVDD not found, using dummy regulator

[ 2.159820] _reglator_get: 2-001b supply DRVDD not found, using dummy regulator

[ 2.170928] asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok

[ 2.178192] asoc: wl1271bt <-> davinci-mcasp.0 mapping ok

[ 2.184844] ALSA device list:

[ 2.187957] #0: AM335X EVM

[ 2.190948] oprofile: hardware counters not available

[ 2.196258] oprofile: using timer interrupt.

[ 2.200897] Netfilter messages via NETLINK v0.30.

[ 2.205963] nf_conntrack version 0.5.0 (7966 buckets, 31864 max)

[ 2.212615] ctnetlink v0.93: registering with nfnetlink.

[ 2.218231] NF_TPROXY: Transparent proxy support initialized, version 4.1.0

[ 2.225524] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.

[ 2.231994] xt_time: kernel timezone is -0000

[ 2.236785] ip_tables: (C) 2000-2006 Netfilter Core Team

[ 2.242584] arp_tables: (C) 2002 David S. Miller

[ 2.247497] TCP cubic registered

[ 2.251007] NET: Registered protocol family 10

[ 2.256500] Mobile IPv6

[ 2.259094] ip6_tables: (C) 2000-2006 Netfilter Core Team

[ 2.264953] IPv6 over IPv4 tunneling driver

[ 2.270019] NET: Registered protocol family 17

[ 2.274719] NET: Registered protocol family 15

[ 2.279357] can: controller area network core (rev 20090105 abi 8)

[ 2.285949] NET: Registered protocol family 29

[ 2.290557] can: raw protocol (rev 20090105)

[ 2.295043] can: broadcast manager protocol (rev 20090105 t)

[ 2.333007] Registering the dns_resolver key type

[ 2.337982] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3

[ 2.346008] ThumbEE CPU extension supported.

[ 2.350524] mux: Failed to setup hwmod io irq -22

[ 2.356201] Power Management for AM33XX family

[ 2.361114] Trying to load am335x-pm-firmware.bin (60 secs timeout)

[ 2.367767] Copied the M3 firmware to UMEM

[ 2.372131] Cortex M3 Firmware Version = 0x181

[ 2.381561] clock: disabling unused clocks to save power

[ 2.388702] Detected MACID=0:18:31:8f:2e:ac

[ 2.395385] input: gpio-keys as /devices/platform/gpio-keys/input/input5

[ 2.402801] omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801)

[ 2.412048] Waiting 1sec before mounting root device...

[ 2.454010] mmc0: new high speed SDHC card at address 1234

[ 2.460235] mmcblk0: mmc0:1234 SA08G 7.28 GiB

[ 2.467041] mmcblk0: p1 p2 p3 p4

[ 2.585693] mmc1: card claims to support voltages below the defined range. These will be ignored.

[ 2.605773] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)

[ 2.612365] mmc1: new high speed SDIO card at address 0001

[ 6.351348] EXT4-fs (mmcblk0p2): recovery complete

[ 6.359741] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)

[ 6.368255] VFS: Mounted root (ext4 filesystem) on device 179:2.

[ 6.375061] Freeing init memory: 344K

[ 6.408630] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.

[ 6.523040] init: cannot open '/initlogo.rle'

[ 7.293457] EXT4-fs (mmcblk0p3): recovery complete

[ 7.298492] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic

[ 7.342102] (stk) :line disc installation timed out

[ 7.361389] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'

[ 7.474121] Disabling lock debugging due to kernel taint

[ 7.480438] Compat-wireless backport release: ol_r8.a5.08

[ 7.486145] Backport based on wl18xx.git ol_r8.a5.13

[ 7.491302] compat.git: wl18xx.git

[ 7.628875] cfg80211: Calling CRDA to update world regulatory domain

[ 7.878570] cfg80211: World regulatory domain updated:

[ 7.884063] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 7.892608] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 7.900665] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 7.908752] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 7.916839] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 7.924926] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 7.993682] wlcore: wl18xx driver version: rowboat-jb-am335x-4.1.2-243-g67c4111

[ 8.005096] android_usb: already disabled

[ 8.009521] android_usb: already disabled

[ 8.026489] android_usb: already disabled

[ 8.031585] mtp_bind_config

[ 8.034637] adb_bind_config

[ 8.057922] adb_open

root@android:/ # [ 8.340698] android_work: sent uevent USB_STATE=CONNECTED

[ 8.346435] android_work: sent uevent USB_STATE=DISCONNECTED

[ 8.437835] gadget: high-speed config #1: android

[ 8.483734] android_work: sent uevent USB_STATE=CONFIGURED

[ 8.491851] warning: `rild' uses 32-bit capabilities (legacy support in use)

[ 9.482360] (stk) :line disc installation timed out

[ 11.602325] (stk) :line disc installation timed out

[ 13.722320] (stk) :line disc installation timed out

[ 14.722381] Bluetooth: st_register failed -22

[ 41.865203] request_suspend_state: wakeup (3->0) at 41832894342 (2000-01-01 00:00:40.950064858 UTC)

[ 42.529571] net eth0: CPSW phy found : id is : 0x4dd074

[ 42.535858] PHY 0:01 not found

[ 42.549652] ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 47.362487] acc_open

[ 47.364807] acc_release

[ 68.232604] adb_release

[ 68.235626] adb_open

[ 68.239044] mtp_bind_config

[ 68.242004] adb_bind_config

[ 68.272583] adb_release

[ 68.372070] init: untracked pid 93 exited

[ 68.377380] adb_open

[ 68.719970] binder: release proc 587, transaction 5464, not freed

[ 68.734771] android_work: sent uevent USB_STATE=DISCONNECTED

[ 68.774536] android_work: sent uevent USB_STATE=CONNECTED

[ 68.780273] android_work: sent uevent USB_STATE=DISCONNECTED

[ 68.861541] android_work: sent uevent USB_STATE=CONNECTED

[ 68.878356] gadget: high-speed config #1: android

[ 68.883758] android_work: sent uevent USB_STATE=CONFIGURED

[ 71.225006] mtp_open

[ 74.578460] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit