Makes approved : CLEARONE CONVERGE / BIAMP AUDIAFLEX

Frequency Range (-10 dB): 50 Hz – 16 kHz

Coverage: 90° conical

9

Sensitivity (2.83V@ 1m): 97 dB (1 kHz - 8 kHz)

Nominal Driver Impedance: 8 ohms

Driver Power Capacity: 25 W

70V/100V Transformer Taps: 6 W, 3 W, 1.5 W, (0.75 W at 70 V only)

Dimensions (Diameter x Depth): 287 mm (11.3 in) diameter round baffle x 104 mm (4.1 in) depth from back

Cutout Dimension: 260 mm diameter (10.1 in)

Should have Clear, High-Fidelity Performance
Makes approved : BOSE / JBL / EXTRON


TECHNICAL SPECIFICATION FOR MULTI-CHANNEL AMPLIFIER

Class D amp with Selectable input sensitivity; 1.4Vrms and .775Vrms options so that amp can be driven at full power, efficient forced-air fans to prevent excessive thermal build-up.
Power	Minimum 200W per channel @ 8Ω
Channels	2
Frequency Response (at 1W, 20Hz to 20kHz)	+0dB, -1dB
Signal to Noise Ratio	> 97dB
Total Harmonic Distortion (at full rated power, 20Hz - 20kHz)	< 0.5%
Intermodulation Distortion (60Hz and 7kHz at 4:1) from full rated output to -30dB	< 0.3%
Voltage Gain	34dB
Damping Factor (8Ω, 10Hz ~ 400Hz)	>200

Makes approved : BOSE / CROWN / YAMAHA

TECHNICAL SPECIFICATION FOR CABLE CUBBY MANAGER

1. 
   Should have access for up to six pass through in the device.
   
2. 
   Should be provisioned with minimum 2 of universal 3-pin type AC socket.
   
3. 
   Should be provisioned with one 15-pin connector along with 3,5mm jack.
   
4. 
   Should be provisioned with one HD format signal connector or HDMI type.
   
5. 
   Should be provisioned with two of RJ45
   
6. 
   Should be able to flush mount inside the table.
   
7. 
   Should have design with tilt-up lid.
   
8. 
   Should have semi-circle cut out on the lid to enable the cables to be used when lid is covered.
   
9. 
   All the cables should be concealed neatly within the table with easy manual retraction.
   

10

TECHNICAL SPECIFICATIONS FOR MULTIFORMAT SWITCHER

• Uncompressed HDMI signal distribution to 60m/197ft

• Class B (HDBaseT-Lite) technology

• Supports Embedded HDMI Lossless Digital Audio

• Full HD resolution support (1080p@60Hz/36bit)

• UHD support (4k@30Hz)

• HD 3D formats & PC resolutions up to WUXGA

• Supports HDCP Repeater and CEC bypass

• Single Cat.5e/Cat.6 Ethernet cable via RJ45

• Bi-directional infrared remote control extensions

• Supports DVI when using Optional HDMI to DVI Adaptors
Makes approved : EXTRON / KRAMER / TV-ONE

TECHNICAL SPECIFICATIONS FOR HDMI RECEIVER
• HDMI w/3D, 4k(24hz/30Hz), HDCP 1.1 & DVI 1.0

• Uncompressed HDMI signal distribution to 60m/197ft

• Class B (HDBaseT-Lite) technology

• Supports Embedded HDMI Lossless Digital Audio

• Full HD resolution support (1080p@60Hz/36bit)

• UHD support (4k@30Hz)

• HD 3D formats & PC resolutions up to WUXGA

• Supports HDCP Repeater and CEC bypass

• Single Cat.5e/Cat.6 Ethernet cable via RJ45

• Bi-directional infrared remote control extensions

• Supports DVI when using Optional HDMI to DVI Adaptors
Makes approved : EXTRON / KRAMER / TV-ONE

12
TECHNICAL SPECIFICATIONS FOR PROCESSOR CONTROLLER

• 
  Enterprise-class control system
  
• 
  Exclusive modular programming architecture
  
• 
  Onboard 512MB RAM & 4GB Flash memory
  
• 
  Expandable storage up to 1TB
  
• 
  Rear panel memory card slot
  
• 
  High-speed USB 2.0 host port
  
• 
  Industry-standard Ethernet and wired communications
  
• 
  XPanel with Smart Graphics™ computer and web based control
  
• 
  iPhone®, iPad®, and Android™ control app support
  
• 
  SNMP remote management support
  
• 
  One RS-232/422/485 COM port with hardware and software handshaking
  
• 
  Two RS-232 COM ports with software handshaking only
  
• 
  Eight IR/serial, eight relay, and eight Versiport I/O ports
  

• 
  Mobile License for Apple iPad
  
• 
  Compatible with Processor cum Switcher
  

• 
  IR emitter probes required to connect to any control system with a 2-pin terminal block type for 1-way IR control interface to the device.
  
• 
  Should have 2-pin 3.5mm detachable terminal block for connection to an IR port.
  
• 
  Should be able to extend up to 1000 feet using ordinary twisted pair cable.
  
• 
  Require minimum of 2nos. of IR emitters with processor.
  

• 
  Should use minimum 9.4" touch panel with wifi to work with the above required application from same manufacturer of the control system required for accessing all the controllable devices in the room.
  

• 
  The Touch Screen should only be of Apple, no other makes are acceptable.
  
• 
  Should have minimum of 32 GB with Wi-fi connectivity.
  

13

TECHNICAL SPECIFICATIONS FOR iPAd DOCKING STATION

• 
  The BaseStation is a table-top mount and inductive charger, capable of receiving iPad.
  
• 
  Color black or silver anodized aluminum finishes.  
  
• 
  Should be supplied along with the compatible Sleeve as a sturdy case for support of all current generation iPads.
  
• 
  It should have soft touch, in black or high-gloss white.
  

• 
  8 Channel Power Relay.
  
• 
  Should be controlled through RS232
  
• 
  Required for controlling the motor screen, Projector Lift and Curtains Control thru Control Processor.
  

1.Display of a alteast 49-Inch diagonal display or above.

2.It should have Direct-LED backlight scanning @ 100Hz

3.It should be a Full HD display with 1920 x 1280 pixels

4.Viewing angle should be 178 degree Horizontal / 178 degree Vertical.

5.Should have following video ports:

a.HDMI 1.4 v x 3

b.RCA pin Type x 1

c.RCA x 1

d.HDMI CEC

e.Mini D-sub 15 pin x 1

f.Audio in (Share with AC)

g.USB Type A connector x 1

6.Should have IR, RS232C control ports.

7.Should have built in 10W + 10W speakers with 10% THD.

8.Power requirement of AC 110~240V, 50 Hz / 60 Hz

9.Rated Power consumption of not more than 100W.

10.Stand-by of approx. < 0.5 W

11.Operating Environment 0°C to 40°C temperature, 20% to 80% humidity.

Makes approved : PANASONIC / SAMSUNG / LG
TECHNICAL SPECIFICATION FOR WALL MOUNT BRACKET FOR ABOVE LED DISPLAY

Size : Suitable to Mount minimum 48” upto 55” LED Display

Adjustment : Adjustment bracket from up/down to left/right Wall Mount Screwed Material : Heavy Metal with Powder coat Finish

Makes approved : CHIEF / CUSTOM

TECHNICAL SPECIFICATION FOR AV PLATE

• 
  Faceplate with VGA&Audio, HDMI each for PC/Laptop presentation
  
• 
  Cable to be managed with external patch cables connectivity type
  

1.Display of a alteast 49-Inch diagonal display or above.

2.It should have Direct-LED backlight scanning @ 100Hz

3.It should be a Full HD display with 1920 x 1280 pixels

4.Viewing angle should be 178 degree Horizontal / 178 degree Vertical.

5.Should have following video ports:

a.HDMI 1.4 v x 3

b.RCA pin Type x 1

c.RCA x 1

d.HDMI CEC

e.Mini D-sub 15 pin x 1

f.Audio in (Share with AC)

g.USB Type A connector x 1

6.Should have IR, RS232C control ports.

7.Should have built in 10W + 10W speakers with 10% THD.

8.Power requirement of AC 110~240V, 50 Hz / 60 Hz

9.Rated Power consumption of not more than 100W.

10.Stand-by of approx. < 0.5 W

11.Operating Environment 0°C to 40°C temperature, 20% to 80% humidity.