User’s Guide (February 2003)
Download 408.75 Kb.
|
- Navigate this page:
- Requirements for Installation
- Ethernet Port (NIC Adapter)
- Account Information (User Name and Password)
- About Bridged Ethernet Connections (RFC 1483)
- About IPoA Connections (RFC 1577)
About This User’s GuideThis user’s guide provides instructions on how to install the DSL-504G ADSL Router and use it to connect a computer or Ethernet LAN (Local Area Network) to the Internet. If you are using a computer with a functioning Ethernet port, you can use the Quick Installation Guide to quickly establish your ADSL connection and access the Internet. Some basic information about Ethernet, networking devices, gateway routers and the TCP/IP suite of protocols is provided in the text of this guide. If you would like to learn more about home or small office networking D-Link has tutorials available at: http://www.dlink.com/learnbasic/ and http://www.dlink.com/learnbasic/homenetwork/ Guide OverviewIntroduction – Describes the Router and its key features. Provides an introduction to ADSL. Lists standards to which the Router complies. Contains a packing list. Hardware Installation – Discusses how to connect the Router to an Ethernet LAN. Configuring the Router for the First Time – Provides information on how to configure the Router and establish the WAN connection using the web-based manager. Web-based Configuration – Describes how to use the web-based manager to change Router settings and configure additional virtual connections (PVCs). Appendix A - Technical Specifications – Lists the technical specifications of the Router, including standards compliance. Appendix B - Low Pass Filters – Illustrated examples of how to install low pass filters. Before You StartPlease read and make sure you understand all the prerequisites for proper installation of your new Router. Have all the necessary information and equipment on hand before beginning the installation. Installation OverviewThe procedure to install the Router is described in general terms in the steps below:
Requirements for InstallationTo install and use the Router you need a computer equipped with an Ethernet port (such as an Ethernet NIC adapter card) and a web browser. You may also need to use information given to you by your service provider. This information is stored in the Router’s memory and used to establish the network connection and confirm your identity. The information may be only your user name (or number) and password, or it may be information used to define your connection profile. The connection profile is used to instruct the Router how to communicate with the computers and other routers that are used to control access to the service provider’s network and ultimately to the Internet. The connection profile is a logical construct that establishes a definite path used for communication and defines the rules or protocols used to initiate and maintain the communication path. Low Pass FiltersSince ADSL and telephone services share the same copper wiring to carry their respective signals, a filtering mechanism may be necessary to avoid mutual interference. A low pass filter device can be installed for each telephone that shares the line with the ADSL line. These filters are easy to install passive devices that connect to the ADSL device and/or telephone using standard telephone cable. Ask your service provider for more information about the use of low pass filters with your installation. Appendix B provides illustrated examples of how to install two common styles of low pass filters. Operating SystemThe DSL-504G uses an HTML-based web interface for setup and management. The web configuration manager may be accessed using any operating system capable of running web browser software. Web BrowserAny common web browser can be used to configure the Router using the web configuration management software. The program is designed to work best with more recently released browsers such as Microsoft Internet Explorer® version 5.0, Netscape Navigator® version 4.7, or later versions. The web browser must have JavaScript enabled. JavaScript is enabled by default on many browsers. Make sure JavaScript has not been disabled by other software (such as virus protection, pop-up ad killer or web user security packages) that may be running on your computer. Ethernet Port (NIC Adapter)Any computer that uses the Router must be able to connect to it through the Ethernet port on the Router. This connection is an Ethernet connection and therefore requires that your computer be equipped with an Ethernet port as well. Most notebook computers are now sold with an Ethernet port already installed. Likewise, most fully assembled desktop computers come with an Ethernet NIC adapter as standard equipment. If your computer does not have an Ethernet port, you must install an Ethernet NIC adapter before you can use the Router. If you must install an adapter, follow the installation instructions that come with the Ethernet NIC adapter. Normally, an Ethernet port will be TCP/IP enabled, this means that it is able to communicate with other computers on an IP network (such as the Internet). Make sure your computer has the TCP/IP protocol installed. If you have accessed the Internet with the computer before, it already has this installed. Additional SoftwareIt may be necessary to install software on your computer that enables it to access the Internet. Additional software must be installed if you are using what is called a “bridged” connection. For a bridged connection, the information needed to make and maintain the Internet connection is stored on your computer, not in the Router. This type of connection is similar to the arrangement used for analog dial-up Routers, but the connection speed is much faster. Various terms are to describe a bridged ADSL connection including the term “1483 Bridged IP” used in this guide. RFC 1484 is a technical standard used to define a bridged connection. If your ADSL service is delivered through a PPP (Point to Point Protocol) connection, the information needed to establish and maintain the Internet connection is stored in the Router. In this case, it is not necessary to install software on your computer. Account Information (User Name and Password)Most users will need to supply a user name and password used to access the service provider’s network (and ultimately, the Internet). This information is stored either in the Router’s memory or on your computer depending on the type of connection profile you use.
About Bridged Ethernet Connections (RFC 1483)Using this method, the DSL-504G acts as a transparent bridge, and is invisible to other devices on both the WAN (wide area network) and LAN (local area network) side of the bridge. It is “invisible” in the sense that it does not have an IP address associated with it. Every device connected to the WAN must have an IP address to be “seen” on the IP network. Devices that connect to the Internet have a “global” IP address that is unique and is used to identify the device so that it can send and receive data. All connections to the Internet require a global IP address. It is therefore necessary to provide some means of acquiring global IP settings for your account. For bridged connections, the global IP settings must reside in a TCP/IP enabled device on the LAN side of the bridge, such as a computer, a server or a firewall device. The IP address can be assigned in a number of ways. Your network service provider will give you instructions about any additional connection software or NIC configuration that may be required. About IPoA Connections (RFC 1577)IP over ATM connections may require global IP settings for the device. Your service provider will give you IP settings information if needed. Some IPoA connections function like peer-to-peer connections and therefore do not require IP settings on the WAN interface. Directory: pub pub -> Project Scoring Template Pre-Construction Phase New Core/Branch Campus Projects pub -> Acm word Template for sig site pub -> The german unification, 1815-1870 pub -> Baltic Olympiads in Informatics: Challenges for Training Together pub -> Preparation of Papers for ieee transactions on medical imaging pub -> Forthcoming meetings and conferences pub -> Asilomar Conference on Circuits, Systems & Computers, Pacific Grove, ca, November 1978, pp. 55 58 pub -> Forthcoming meetings and conferences pub -> Harmonised compatibility and sharing conditions for video pmse in the 7 9 ghz frequency band, taking into account radar use Download 408.75 Kb. Share with your friends:
|