Activity/Operation Adverse weather conditionHeavy wind Night time operation Heavy fog/mist Rig up / Rig down Rigging up Isolation tool Pressure testing Handling loads with crane Pump maintenance Frac operation Filling diesel Washing units Prevention for fire related: Absolute interdiction for gasoline. All employees should have Certification Fire level 1. Avoid fueling with people inside the enclosed unit or an elevated platform (restricted escape routes). Avoid splashes when filling the tank. Communication, with agreed protocol among all parties involved. Ensure a nozzle man and diesel truck driver assigned to the job. Hot Permit to work completed and signed by a competent PTW holder. Keep fume generation at a minimum by not leaving unnecessary open tanks. Maximize visibility (Wear hi-vis vest). Mobile phone switched off during operation. No smoking, no spark sources (electrostatic, electrical sources). Consider weather conditions mainly windstorms. Pre-job safety meeting. Taping off area (keep off sources of ignition and possible victims). The tanker should be minimum of 2 meters away from equipment being filled up. Work Instruction training. Prevention for Falling (person): All people on location to complete WS Safety standard 5. Crew to help each other when moving treating iron more than 15-20 Kg. Employees working on high levels to have safety harness on, or protecting bars on equipment to protect them from falling Iron Wrack, to be at the same level with the personnel to ease the usage O/I needs to be practiced at all timesPeople are fit to work and have enough rest before starting the job with valid medical checkup People trained to do the job (not first time) Pre job meeting to include all the assignments and requirements for each individual Proper Hammer and in good conditions to be used when Loosing/tightening treating iron connections Proper PPE to be used on all locations Rigging up procedures according to Standard 5 SIPP Level 2 Training to completed by all the crew on location and documented in QUEST Use Crane to move heavy tools Use proper technique of hammering, and make sure the area around you is clear of equipment and personnel # Schlumberger-Private
When moving up or down on a ladder, make sure you have a 3 point contact at all time ( stairs into the office, or stepping inside a car or truck..) Younger people to help older employees in rigging up and moving treating equipments Prevention for Graviational energy release: Agreed procedure and communication signs Barrier around the area Competent personal for the lifting Dedicated banks man to control the operation Lifting plan to be filled and correct procedure to be followed Tool box meeting before the lifting Visual inspection of all lifting gears and valid certificate to be available All areas to be clear of trip hazards Good communication between personnelLifting aids are available if required No carrying by one person of more than 25 lbs Permit to Work for rigging up Personnel familiar with site / location Risk Assessment prior to carrying Safe path to be outlined before transferring equipment SIPP Training Prevention for Frac associatted risks: All treating Iron must be inspected according to Well Services Standard 23 Bleed off valves must be secured and opened correctly according to Standard 5 Customer / Client representative to know about the pressure trips Ensure that safety signs and tape barrier is surrounding the pressure Area Maximum Pressure to be known by every employee on location and everyone working on the high pressure pumps - No treating iron to be used if there is no certification tag on or the certificate date is older than 1 year Only one person should be allowed to check the lines as per PTW- People involved in the pressure test must have Well Services Safety Standard 5 completed and signed on there passportsPressure relief valves are set and tested before the start of the job - Pressure test (25% of total pressure, must hold before continuing to the final pressure test limit) Proper communication to be present at all times (radio or signs agreed on before the start of the operations) Pumps are adequate for the job, including (Max. Rate and Pressure) Pumps checked and maintenance is done on them before the star of the job Safety Meeting to be held before starting of the pressure test operation Trip pressures are set on all pumps involved in the operation Prevention for Land transportation: Certified trucking contractor and drivers Convoy driving (Journey Management) Pre-move meeting to discuss routes and hazards (Journey Management) Regular stops Route inspected by frac master before mobilization (Journey Management) # Schlumberger-Private
use of certified trucks It's prohibited to use personal car in order to drive to location until it's register in eJourney system and trip is approved on appropriate level. Minimize number of trips (Bus schedule) Reduce distance to camp to minimal distanceRigorous implementation and control of SLB and client driving policies and standards Speed limit: 60km/hr Graded Road; 40km/hr Non-Graded Road. All equipment within crane capacity Certified crane Certified slings Competent banks man with High visibility Vest Competent personnel Familiarity with location Good communication Good planning Permit to work Placement of equipment known Toolbox talk Visible load rating of craneVisual inspection of all lifting equipment Certified & competent fork-lift driver Certified fork lift Good communication Permit to work Proper operation of fork-lift Proper operation of fork-lift Reverse horn working on fork-lift Visible loading capacity on fork-lift Land guides with hi-vis vests Pre-move meeting to line up equipment order. Site inspection by frac master before mobilizationStandard layout prepared # Schlumberger-Private
Heavy rain Lighting High temperature >50C Graviational energy release Manual lifting Mechanical lifting Falling (person) No smoking, no spark sources (electrostatic, electrical sources). Consider weather conditions mainly windstorms. Employees working on high levels to have safety harness on, or protecting bars on equipment to protect them from falling Use proper technique of hammering, and make sure the area around you is clear of equipment and personnel # Schlumberger-Private
When moving up or down on a ladder, make sure you have a 3 point contact at all time ( stairs into the office, or stepping inside a car or truck..) Maximum Pressure to be known by every employee on location and everyone working on the high pressure pumps - People involved in the pressure test must have Well Services Safety Standard 5 completed and signed on there passports Proper communication to be present at all times (radio or signs agreed on before the start of the operations) # Schlumberger-Private
It's prohibited to use personal car in order to drive to location until it's register in eJourney system and trip is approved on appropriate level. # Schlumberger-Private
Fire related Fire hazard from equipment running engines in extreme temperature # Schlumberger-Private
# Schlumberger-Private
# Schlumberger-Private
Filling diesel in frac equipment Frac associatted risks Equipment failure Uncontrolled pressure release # Schlumberger-Private
# Schlumberger-Private
# Schlumberger-Private
Unexpected discahrge of hazardous fluids Hose Burst HP line whipping Land transporta tion Damaged equipment Vehicle accident Load stuck # Schlumberger-Private
# Schlumberger-Private
# Schlumberger-Private
Share with your friends: |