Forward Traffic Channel Power Control Initialization

2.6.4.1.1.2 Processing the Power Control Parameters Message

• Power control reporting threshold (PWR_REP_THRESH_s = PWR_REP_THRESH_r)

• Power control reporting frame count (PWR_REP_FRAMES_s = PWR_REP_FRAMES_r)

• Threshold report mode indicator

• Periodic report mode indicator

• Power report delay (PWR_REP_DELAY_s = PWR_REP_DELAY_r)

The mobile station shall set TOT_FRAMES_s and BAD_FRAMES_s to zero if FCH is assigned. The mobile station shall set DCCH_TOT_FRAMES_s and DCCH_BAD_FRAMES_s to zero if DCCH is assigned.

2.6.4.1.1.3 Processing the Power Control Message

• If the mobile station does not support any Radio Configuration greater than 2 and FPC_MODE_r is not supported by the mobile station.

• If the mobile station does not support Supplemental Channel and FPC_MODE_r is set to the ‘001’, ‘010’, ‘101’, or ‘110’.

• If PWR_CNTL_STEP_r corresponds to a power control step size (see [2]) is not supported by the mobile station.

The mobile station shall send a Mobile Station Reject Order with the ORDQ field set to ‘00000111’ (message cannot be handled by the current mobile station configuration) if any of the following conditions are detected:

• FPC_PRI_CHAN_r is set to ‘1’ and only the Fundamental Channel is assigned.

• FPC_PRI_CHAN_r is set to ‘0’ and only the Dedicated Control Channel is assigned.

If none of the above conditions are true, the mobile station shall process the message as follows at the action time (see 2.6.4.1.5) specified in the message:

• The mobile station shall store the power control step size (PWR_CNTL_STEP_s = PWR_CNTL_STEP_r).

• If FPC_INCL_r is equal to ‘1’, the mobile station shall perform the following:

– The mobile station shall set FPC_MODE_NO_SCH_s = FPC_MODE_r.

– The mobile station shall set FPC_MODE_s = FPC_MODE_NO_SCH_s if there is no forward Supplemental Channel burst in progress (see 2.6.6.2.5.1.1).

– The mobile station shall set FPC_PRI_CHAN_s to FPC_PRI_CHAN_r

– If FPC_OLPC_FCH_INCL is equal to ‘1’, the mobile station shall:

+ Set FPC_FCH_FER_s to FPC_FCH_FER_r.

+ If FPC_FCH_MIN_SETPT_r is not equal to ‘11111111’, set FPC_FCH_MIN_SETPT_s to FPC_FCH_MIN_SETPT_r; otherwise, set FPC_FCH_MIN_SETPT_s to FPC_FCH_CURR_SETPT_s.

+ If FPC_FCH_MAX_SETPT_r is not equal to ‘11111111’, set FPC_FCH_MAX_SETPT_s to FPC_FCH_MAX_SETPT_r; otherwise, set FPC_FCH_MAX_SETPT_s to FPC_FCH_CURR_SETPT_s.

– If FPC_OLPC_DCCH_INCL is equal to ‘1’, the mobile station shall:

+ Set FPC_DCCH_FER_s to FPC_DCCH_FER_r.

+ If FPC_DCCH_MIN_SETPT_r is not equal to ‘11111111’, set FPC_DCCH_MIN_SETPT_s to FPC_DCCH_MIN_SETPT_r; otherwise, set FPC_DCCH_MIN_SETPT_s to FPC_DCCH_CURR_SETPT_s.

+ If FPC_DCCH_MAX_SETPT_r is not equal to ‘11111111’, set FPC_DCCH_MAX_SETPT_s to FPC_DCCH_MAX_SETPT_r; otherwise, set FPC_DCCH_MAX_SETPT_s to FPC_DCCH_CURR_SETPT_s.

– If FPC_INCL is equal to '1' and FPC_MODE is equal to '001', '010', ‘101’, or ‘110’, the mobile station shall:

+ Set FPC_SEC_CHAN_s to FPC_SEC_CHAN_r.

+ Set FPC_BCMC_CHAN_s to FPC_BCMC_CHAN_r.

– If NUM_SUP_r is not equal to ‘00’, for each Supplemental Channel included in the message, the mobile station shall:

+ Set SCH_ID_s to SCH_ID_r.

+ Set FPC_SCH_FER_s[SCH_ID_s]  to FPC_SCH_FER_r.

+ If FPC_SCH_MIN_SETPT_r is not equal to ‘11111111’, set FPC_SCH_MIN_SETPT_s[SCH_ID_s] to FPC_SCH_MIN_SETPT_r; otherwise, set FPC_SCH_MIN_SETPT_s[SCH_ID_s] to FPC_SCH_CURR_SETPT_s.

+ If FPC_SCH_MAX_SETPT_r is not equal to ‘11111111’, set FPC_SCH_MAX_SETPT_s[SCH_ID_s] to FPC_SCH_MAX_SETPT_r; otherwise, set FPC_SCH_MAX_SETPT_s[SCH_ID_s] to FPC_SCH_CURR_SETPT_s.

– If FPC_THRESH_INCL is equal to ‘1’, the mobile station shall set FPC_SETPT_THRESH_s to FPC_SETPT_THRESH_r.

– If FPC_THRESH_SCH_INCL is equal to ‘1’, the mobile station shall set FPC_SETPT_THRESH_SCH_s to FPC_SETPT_THRESH_SCH_r

• If RPC_INCL_r is equal to ‘1’ and the mobile station supports any Radio Configuration greater than 2, the mobile station shall perform the following:

– If RPC_ADJ_REC_TYPE is equal to ‘0000’, the mobile station shall update the Reverse Channel Adjustment Gain Table (see [2]) containing an offset relative to the Reverse Pilot Channel power for each reverse link code channel received in this message.

– If RPC_ADJ_REC_TYPE is equal to ‘0001’ or ‘0010’, the mobile station shall update the Reverse Link Attribute Adjustment Gain Table (see [2]) containing an offset relative to the Reverse Pilot Channel power for each transmission rate, frame length, coding type received in this message.

– If RPC_ADJ_REC_TYPE is equal to ‘0011’, at the action time of the message, the mobile station shall update the Reverse Link Attribute Adjustment Gain Table (see [2]) containing an offset relative to the Reverse Pilot Channel power for the R-CQICH.

– If RPC_ADJ_REC_TYPE is equal to ‘0100’, the mobile station shall perform the following:

+ At the first R-PDCH frame boundary at or after the action time of the message, the mobile station shall update the Reverse Link Attribute Adjustment Gain Table (see [2]) containing an offset relative to the Reverse Pilot Channel power for any combination of the following channels:

 R-REQCH,

 R-SPICH,

 R-PDCCH possibly for each encoder packet size, or for the boosted and non boosted modes

 R-PDCH possibly for each encoder packet size, or for the boosted and non boosted modes, or for each encoder packet size and transmission round.

+ At the action time of the message, the mobile station shall update the Reverse Link Attribute Adjustment Gain Table (see [2]) containing an offset relative to the Reverse Pilot Channel power for the R-ACKCH.

+ If REV_SPICH_ADJ_INCL_r is equal to ‘1’, the mobile station shall set REV_SPICH_EP_SIZE_s to REV_SPICH_EP_SIZE_r+1.

+ If REV_PDCH_PARMS_INCL_r is equal to ‘1’, the mobile station shall set REV_PDCH_NUM_ARQ_ROUNDS_NORMAL_s to REV_PDCH_NUM_ARQ_ROUNDS_NORMAL_r+1, and REV_PDCH_NUM_ARQ_ROUNDS_BOOST_s to REV_PDCH_NUM_ARQ_ROUNDS_BOOST_r+1.