Softwares List in General

Softwares List in General

Survey and Investigation Works As provided in the documents

Process

API 520 Part I and II Recommended Practice for Sizing, Selection and Installation of Pressure Relieving Devices in Refineries

API 521 Guide for Pressure Relieving and Depressurising Systems.

API STD 610 Centrifugal Pumps for Petroleum, Chemical and Gas Industry Services

API STD 613 Special Purpose Gear Units for Petroleum, Heavy Duty Chemical and Gas Industry Services

API STD 617 Centrifugal Pumps for Petroleum, Chemical and Gas Industry Services

ASME Section VIII, Div. 1 Rules for Construction of Pressure Vessels. NACE MR 01-75 Standard Material Requirements, Sulphide Stress Cracking Materials for Oil Field Equipment.

API 2000 Venting Atmospheric and Low Pressure Storage Tanks, fourth edition, September, 1992.

API 2610 Design, Construction, Operation, Maintenance and Inspection of Terminals and Tank Facilities

Mechanical

National Standards Not provided Construction Standards Instrumentation & Control (ICA)

International Standards

BS 5308 Part 1 Instrument Cables – Polyethylene Insulated Cables

BS 5308 Part 2 Instrument Cables – PVC Insulated Cables

BS 5345 Installation and Maintenance Requirements for Electrical Apparatus – Type of Protection (I)

BS 6121 Cable Glands BS 7405 Guide to the Selection of and Application of Flowmeters for Measurement of Fluid Flow in Closed Conduits

ISO 5167-1 Specification for Square-Edged Orifice Plates, Nozzles and Venturi Tubes

ISO 5168 Methods of Measurement of Fluid Flow Estimation of Uncertainty of a Flow Rate Measurement

ISO 5210 Industrial Valves – Multi-Turn Valve Actuators

ISO 5211 Industrial Valves – Part-Turn Valve Actuators TS/AS/009 Technical Standard on Non-Relieving over Pressure Protection (The Netherlands Steam Institute)

NACE MR-01-75 Material Requirements Sulphide Cracking Resistant Metallic Material For Oil Field Equipment

IEC 60051 Direct Acting Indicating Analogue Electrical Measuring Instruments

IEC 60079 Electrical Apparatus for Explosive Gas Atmosphere

IEC 60227 Specification for PVC Insulation and Sheath of Electrical Cables IEC 60331 Fire Resisting Characteristics of Electrical Cables

ASTM A106Standard specification for carbon steel pipes

ASTM D695Standard test method for compressive properties of rigid plastics ASTM D1599Standard test method for short time hydraulic failure pressure of plastic pipe, tubing and fittings

ASTM D2105Standard test method for longitudinal tensile properties of “fiberglass” (glass fiver reinforced thermosetting resin) pipe and tube

ASTM D2290Standard test method for apparent tensile strength of ring or Tubular plastics and reinforced plastics by split disk method

ASTM D2412Standard test method for determination of external loading characteristics of plastic pipe by parallel plate loading

ASTM D2992Standard practice for obtaining hydrostatic or pressure design basis for “fiberglass” pipe and fittings

ASTM D3517Standard specification for “fiberglass” pressure pipe ASTM D3567Standard practice for determining dimensions of “fiberglass” Pipe and fittings

ASTM D3681Standard test method for chemical resistance of “fiberglass” pipe in a deflected condition

ASTM D4161Standard specification for “fiberglass” pipe joints using Flexible elastomeric seals

ASTM F412Standard terminology relating to plastic piping systems

ASTM D883Standard terminology relating to plastics

ASTM D1600Standard terminology for abbreviated terms relating to plastics ASTM D2310Standard classification for machine made “fiberglass” pipe ASTM D2517Standard specification for reinforced epoxy resin gas pressure pipe and fittings

ASTM D2996Standard specification for filament wound “fiberglass” pipe ASTM D2997Standard specification for centrifugally cast “fiberglass” pipe ASTM D3262Standard specification for “fiberglass” sewer pipe

ASTM D3754Standard specification for “fiberglass” sewer and industrial pressure pipe

ASTM D4024Standard specification for machine made “fiberglass” flanges ASTM F1173Standard specification for thermosetting resin fiber glass pipe and fittings to be used for marine applications

ASTM D3839Standard practice for underground installation of “fiberglass” Pipe

ASTM D790Standard test method for flexural properties of un-reinforced And reinforced plastics and electrical insulating materials

ASTM D2925Standard test method for beam deflection of “fiber glass” Pipe under full bore flow

ASTM D2143Standard test method for cyclic pressure strength of reinforced, thermosetting plastic pipe

ASTM D1598Standard test method for time to failure of plastic pipe under constant internal pressure

ASTM D2924Standard test method for external pressure resistance of “fiberglass” pipe

ASTM C581Standard practice for determining chemical resistance of thermosetting resins used in glass fiber reinforced structures intended for liquid service

ASME B31.3Process piping

ASME B31.4 Pipeline transportation systems for liquid hydrocarbons and Other liquids

ANSI B16.5Steel Pipe Flanges and Flanged Fittings

ANSI B16.9Steel Butt Welding Fittings

ANSI B16.10Face-to-Face and End-to-End dimensions of Valves

ANSI B16.20Metallic Gaskets for Pipe Flanges - ring joint, spiral wound

ANSI B16.21Nonmetallic Flat Gaskets for Pipe Flanges

ANSI B16.47Large Diameter Steel Flanges - NPS - 26" to 60ANSI B36.10Welded and Seamless Wrought Steel Pipes

ANSI B36.19Welded and Seamless Austinitic Stainless Steel Pipe BS 1868Steel Check Valves for Petroleum Industry

BS 1873B Steel Globe and Check Valves for Petroleum Industry

S 5351Steel Ball Valves for Petroleum Industry

BS 5352Steel Gate, Globe and Check Valves, smaller than 2" NB

BS 6755Testing of valves

BS EN 10204Metallic products – type of inspection

NACE MR0175Sulfide Stress Cracking Resistant Metallic

Materials for Oilfield Equipment

NACE RP0286The Electrical isolation of Cathodically protected pipelines ISO 14692EJMA STD Standards of the expansion joint manufacturers association, Inc Civil and Structural

National standards/specifications- QP shall not supply copies of these standards.

EPIC Contractor shall have to obtain his own copies from the Ministry of Municipal Affairs and Agriculture.The Qatar Construction Specifications (QCS).Qatar Highway Design Manual

Marine Breakwater

BS 6349- British Standard Code of Practice for the Design of Maritime Structure.

US Army Corps of Engineers Shore Protection Manual:

1984CIRIA Report 154: 1991 – Manual on the use of rock in coastal and shoreline engineering Delft Hydraulics Report no 483: 1983 –Conceptual design of rubble mound breakwaters HR Wallingford Ltd R&D Technical Report W178.

Overtopping of seawalls – Design and Assessment Manual Delft Hydraulics Computer Program ‘Breakwater’ Version 3.0 Conceptual Design Tool for Breakwater Structures

ES.2.14.0003 for Navigation Aids, Rev. A (listed under 5-B)

Telecommunication

CCWP FEED Phase- II: Mechanical specifications and references there to.

Also references have been to various tender documents during the professional experience used for collection of information purpose only

AASHTO - American Association of State Highways and Transportation Officials

ACGIH - American Conference of Governmental Industrial Hygienists

ACI - American Concrete Institute

AGA - American Gas Association

AGMA - American Gear Manufacturers Association

AISC - American Institute of Steel Construction

ALPEMA - Brazed Aluminum Plate-Fin Heat Exchanger Manufacturers Association

AMCA - Air Movement and Control Association

ANSI - American National Standards Institute

API - American Petroleum Institute

API (MPMS) - API Manual of Petroleum Measurement Standards

ASCE - American Society of Civil Engineers

ASHRAE - American Society of Heating, Refrigeration, Air Conditioning

ASME - American Society of Mechanical Engineers

ASTM - American Society of Testing and Materials

ATEX - Atmosphere Explosible

AWS - American Welding Society

BS - British Standards

CINI - Stichting Isolatie Nederlandse Industrie

CEB - Comite Euro-international du Beton

CICIND - International Committee on Industrial Chimneys

CONCAWE - European Organisation for Environment, Health and Safety

DIN - Deutsches Institut Fur Normung

EEMUA - Engineering Equipment and Materials Users Association

EIA - Electronics Industry Alliance

EJMA - Expansion Joint Manufacturers Association

EN - Comite European de Normalisation

ERA - Electronics Representatives Association

FCI - Fluid Control Institute

FEM - Federation Europeene de la manutention

FIP - Federation Internationale de la Precontrainte

HEI - Heat Exchange Institution

HTFS - Heat Transfer and Fluid Service

ICAO - International Civil Aviation Organisation

IEC - International Electrical Committee

IEEE - Institute of Electrical and Electronic Engineering

IP - Institute of Petroleum

ISA - Instrument Society of America

ISBN - International Standard Book Number

ISGOTT - International Safety Guide for Oil Tankers and Terminals

ISO - International Organisation for Standardisation

ISSMFE - International Society for Soil Mechanics and Foundation Engineering

ITU - International Telecommunications Union

MIL-HDBK - US Military Handbook

MSS - Manufacturers Standardisation Society

NACE - National Association of Corrosion Engineers NAMUR

NAS - National Standards Association

NEN - Nederlands Normalisatie-Institutuut

NFPA - National Fire Protection Association

OCIMF - Oil companies international marine forum

PrEN - Draft EN Standard

RAL - Deutsches Institut fur Gutesicherung und Kennzeichnung

SMACNA - Sheet Metal and Air Conditioning Contractors National Association

SSPC - Steel Structures Painting Council

TEMA - Standards of the Tubular Exchanger Manufacturers Association

TIA - Telecommunications Industry Association

UBC - Uniform Building Code

UL - Underwriters Laboratories Inc

USEPA - United States Environmental Protection Agency

VDE - Verband Deutscher Elektrotechniker

VDI - Verein Deutscher Ingenieure

WRC - Welding Research Council APPENDICES

AASHTO Guide for design of pavement structures

ACGIH Threshold limit values for chemical substances and physical agents, an biological exposure indices

Advisory Circular Obstruction Marking and Lighting (issued by Aviation Administration)

AC70/7460-1K

AGA-9 Report 9, Measurement of Gas: Ultrasonic Meters

AGMA 6011 Specification for High speed helical gear units

AISC Steel Construction manual

ALPEMA Plate-fin heat exchangers

AMCA Publication 203 Field performance measurement of fan systems

ANSI/ASME B1.1 Unified inch screw threads

ANSI/ASME B1.20.1 Pipe threads, General purpose (inch)

ANSI/ASME B16.3 Malleable iron threaded fittings classes 150 and 300

ANSI/ASME B16.5 Pipe flanges and flanged fittings NPS ½” to NPS 24”

ANSI/ASME B16.9 Factory-made wrought steel butt welding fittings

ANSI/ASME B16.10 Face-to-face and end to end dimensions of valves

ANSI/ASME B16.11 Forged steel fittings, socket-welding and threaded

ANSI/ASME B16.20 Metallic gaskets for pipe flanges - Ring-joint, spiral-wound, and jacketed

ANSI/ASME B16.21 Non-metallic flat gaskets for pipe flanges

ANSI/ASME B16.24 Cast copper alloy pipe flanges and flanged fittings

ANSI/ASME B16.25 Butt welding ends

ANSI/ASME B16.34 Valves: flanged, threaded and welding ends

ANSI/ASME B16.36 Orifice flanges

ANSI/ASME B16.47 Large diameter steel flanges NPS 26” to NPS 60”

ANSI/ASME B16.48 Steel line blinds

ANSI/ASME B16.104 Control valve seat leakage

ANSI/ASME B31.1 Power piping

ANSI/ASME B31.3 Process piping

ANSI/ASME B31.4 Pipeline transportation systems for liquid hydrocarbons and other liquids

ANSI/ASME B31.5 Refrigeration piping

ANSI/ASME B31.8 Gas transmission and distribution piping systems

ANSI/ASME B36.10M Welded and seamless wrought steel pipe

ANSI/ASME B36.19M Stainless steel pipe

ANSI/ASME B46.1 Surface texture

ANSI B133.8 Gas Turbine Installation Sound Emissions

ANSI/FCI 70.2 Quality control standard for control valve seat leakage

ANSI/ISA S51.1 Process instrumentation terminology

ANSI/ISA S75.02 Control valve capacity test procedures

ANSI MC 96-1 Temperature measurement thermocouples

API (MPMS) Chapter 12 Calculation of petroleum quantities

API (MPMS) Chapter 2 Cylindrical Tanks

API (MPMS) Chapter 4 Proving systems

API (MPMS) Chapter 5 Metering

API (MPMS) Chapter 6 Metering assemblies

API 5L Replaced by ISO 3183

API 6D Specification for pipeline valves

API 6FA Specification for fire test for valves

API 15LE Specifications for polyethylene (PE) line pipe

API 510 Pressure Vessel Inspection Code: Maintenance Inspection, rating, repair and alteration

API RP 520 Part 1 Sizing, selection, and installation of pressure relieving devices in refineries

API RP 520 Part 2 Sizing, selection, and installation of pressure relieving devices in refineries

API RP 521 Guide of pressure relieving and depressurizing system

API 526 Flanged steel pressure relief valves

API 527 Seat tightness of pressure relief valves

API 530 Refer ISO 13704 (Calculation of heater tube thickness in petroleum refineries)

API 536 Post combustion NOx control for fired equipment in general refinery services

API 541 Form-wound squirrel cage induction motors – 250 HP and larger

API 546 Form-wound brushless synchronous motors – 500 HP and larger

API 551 Process measurement instrumentation

API 552 Transmission systems

API 554 Process instruments and control

API 555 Process analysers

API 560 Refer ISO 13705 (Fired heaters for general refinery services)

API 582 Welding guidelines for the chemical, oil and gas industries

API 594 Check valves; wafer, wafer-lug and double flanged type

API 598 Valve inspection and testing

API 600 Steel gate valves – flanged and butt welding ends, bolted and pressure seal bonnets

API 601 Replaced by ANSI/ASME B 16.20

API 602 Compact carbon steel gate valves – Flanged, threaded, welding and extended body ends

API 608 Metal Ball valves – Flanged, threaded and welding ends

API 609 Butterfly valves; double flanged, lug and wafer type

API 610 Centrifugal pumps for petroleum, petrochemical and natural gas Industries – not used – refer to BS EN ISO 13709

API 611 General purpose steam turbines for petroleum, chemical and gas industry services

API 612 Special purpose steam turbines for petroleum, chemical and gas industry services

API 614 Lubrication, shaft-sealing, and control-oil systems and auxiliaries for petroleum, chemical and gas industry services

API 616 Gas turbines for petroleum, chemical and gas industry services

API 617 Axial and Centrifugal compressors and expanders - Compressors for petroleum, chemical and gas industry services

API 618 Reciprocating compressors for petroleum, chemical and gas industry services

API 619 Rotary-type positive displacement compressors for petroleum, chemical and gas industry services

API 631M Measurement of Noise from Air-Cooled Heat Exchangers

API 650 Welded Steel Tanks for Oil Storage

API 662 Plate heat exchangers for general refinery services

API 670 Machinery protection systems

API 671 Special purpose couplings for petroleum, chemical and gas industry services

API 672 Packaged, integrally geared centrifugal air compressors for petroleum, chemical and gas industry services

API 673 Centrifugal fans for petroleum, chemical and gas industry service

API 674 Positive displacement pumps - Reciprocating

API 675 Positive displacement pumps - Controlled volume

API 676 Positive displacement pumps - Rotary

API 677 General purpose gear unit for petroleum, chemical and gas industry services

API 681 Liquid ring vacuum pumps and compressors

API 682 Shaft sealing systems for centrifugal and rotary pumps

API RP 686 Machinery installation and installation design

API 934 Materials & Fabrication Requirements for 2-1/4Cr-1MO & 3Cr-1Mo Steel Heavy Wall Pressure Vessels for High Temperature, High Pressure Hydrogen Service, 1st Edition, 2000

API 945 Avoiding Environmental Cracking in Amine Units- Third Edition.

API 2000 Venting atmospheric and low-pressure storage tanks, non refrigerated and refrigerated

API 2218 Fireproofing practices in petrochemical processing plant

API 2510 Design and construction of LPG installations

API 2550 Method for measurement and calibration of upright cylindrical tanks

API RP 500 Classifications of locations for electrical installations at petroleum facilities classified as Class 1, Division 1, Division 2

API RP 505 Classifications of locations for electrical installations at petroleum facilities classified as Class 1, Zone 0, Zone 1, and Zone 2

API RP 572 Inspection of Pressure Vessels

API RP 576 Inspection of Pressure-relieving Devices

API RP 651 Cathodic protection of aboveground petroleum storage tanks

ASCE Design of blast resistant buildings in petrochemical facilities

ASCE 7-95 Minimum design loads for buildings and other structures

ASHRAE Handbooks - Refrigeration

ASHRAE Handbook- HVAC applications

ASHRAE Handbook - Fundamentals

ASHRAE Handbooks - HVAC systems and equipment

ASHRAE 16 Method of testing for rating room air conditioners and packaged terminal air conditioners

ASHRAE 23 Methods of testing for rating positive displacement refrigerant compressors and condensing units

ASHRAE 30 Methods of testing liquid chilling package

ASHRAE 37 Methods of testing for rating unitary air-conditioning and heat pump equipment

ASHRAE 40 Methods of testing for rating heat operated unitary air-conditioning equipment for cooling

ASHRAE 52.1 Gravimetric and dust spot procedures for testing air cleaning devices used in general ventilation for removing particulate matter

ASHRAE 55 Thermal environmental conditions for human occupancy and addendum

ASHRAE 62 Ventilation for acceptable indoor air quality

ASHRAE 63.1 Method of testing liquid line refrigerant driers

ASHRAE 70 Method of testing for rating the performance of air outlets and inlets

ASHRAE 79 Methods of testing for rating room fan-coil air conditioners

ASHRAE 111 Practices for measurement, testing, adjusting and balancing of building heating, ventilation, air conditioning and refrigeration systems.

ASHRAE Guideline 1 The HVAC Commissioning Process

ASHRAE Guideline 4 Preparation of operating and maintenance documentation for building systems

ASHRAE Guideline 5 Commissioning of smoke management systems

AASHTO GDPS 4 Guide for design of pavement structures

AASHTO T180 Standard Method of testing for moisture-density relations of soils using a 4.45 kg rammer and 457 mm drop

ASME B16.3 Malleable iron threaded fittings, classes 150# & 300#

ASME PTC 1 General instructions for performance test codes

ASME PTC 4.1 Steam generating units

ASME PTC 4.4 Gas turbine heat recovery steam-generating units

ASME PTC 6 Steam Turbines

ASME PTC 9 Displacement compressors

ASME PTC 10 Performance test code : compressors and exhausters

ASME PTC 16 Gas Generators

ASME PTC 19.3 Temperature measurement – Instruments and apparatus

ASME PTC 22 Performance test code : gas turbines

ASME PTC 26 Speed governing systems for internal combustion engine/generator sets

ASME Section I Power Boilers

ASME Section II Material specifications Part A, B, C and D

ASME Section III Creep design basis fatigue analysis

ASME Section IX Qualification standard for welding and brazing procedures

ASME Section V Non-destructive examination

ASME Section VIII Div. 1 and 2, Boiler and vessel code

ASME RTP-1 Reinforced thermoset plastic corrosion resistant material

ASTM A 48 Standard specification for gray iron castings

ASTM A53 Standard Specification for Pipe, Steel, Black and Hot Dipped, Zinc Coated, Welded and Seamless

ASTM A 105/105M Forgings, carbon steel, for piping applications

ASTM A 106 Seamless carbon steel pipe for high temperature service

ASTM A 123/A123M Standards - Specification for zinc (hot dip galvanised) coating on iron and steel products, version A

ASTM A 167 Standard specification for stainless and heat resisting chromium-nickel steel plate, sheet and strip

ASTM A 179/A179M Seamless cold-drawn low-carbon steel heat-exchanger and condenser tubes

ASTM A 182/A182M Forged or rolled alloy-steel pipe flanges, forged fittings, and valves and parts for high-temperature

ASTM A 193/A193M Standard specification for alloy steel, stainless steel and stainless steel bolting materials for high temperature service

ASTM A 194/A194M Standard specification for carbon alloy and steel nuts for bolts for high pressure or high temperature service, or both

ASTM A 213/A213M Seamless ferritic and austenitic alloy - steel boiler, superheater and heat-exchanger tubes

ASTM A 216/A216M Specification for carbon steel castings, suitable for fusion welding, for high temperature service

ASTM A 234/A234M Pipe fittings of wrought carbon steel and alloy steel for moderate and elevated temperatures

ASTM A 240/A240M Standard specification for heat resisting chromium nickel stainless steel plate, sheet, and strip for pressure vessels

ASTM A 262 Standard practices for detecting susceptibility to intergranular attack in austenitic stainless steels

ASTM A 269 Standard specification for seamless and welded austenitic stainless steel tubing for general service

ASTM A 276 Standard specification for stainless steel bars and shapes

ASTM A 285 Standard Specification for Pressure Vessel Plates, Carbon Steel, Low and Intermediate-Tensile Strength

ASTM A 307 Standard Specification for Carbon Steel Bolts and Studs, 60,000 P.S.I. Tensile Strength

ASTM A 312/A312M Seamless and welded austenitic stainless steel pipes for general service

ASTM A 320/A320M Alloy-steel bolting materials for low-temperature service

ASTM A325 Standard Specification for Structural bolts, steel, heat treated, 120/105 ksi minimum tensile strength-AASHTO no:M164.

ASTM A 333/A333M Seamless and welded steel pipe for low-temperature service

ASTM A 334/A334M Seamless and welded carbon and alloy - Steel tubes for low-temperature service

ASTM A335 Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

ASTM A 350/A350M Forgings, carbon and low-alloy steel, requiring notch toughness testing for piping components

ASTM A 351/A351M Specification for steel castings, austenitic, for high temperature service

ASTM A 352/A352M Specification for steel castings, ferritic and martensitic, for pressure containing parts suitable for low temperature service

ASTM A 353/A353M Pressure vessel plates, alloy steel, 9% nickel, double normalised and tempered

ASTM A 358/A358M Standard specification for electric-fusion-welded austenitic chromium-nickel alloy steel pipe for high temperature service

ASTM A 388/A388M Practice for ultrasonic examination of heavy steel forgings

ASTM A 392 Standard specification for zinc coated steel chain link fence fabric

ASTM A395 Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures

ASTM A 403/A403M Wrought austenitic stainless steel piping and fittings

ASTM A 420/A420M Piping fittings of wrought carbon steel and alloy steel for low-temperature service

ASTM A 450/A450M Standard specification for carbon, ferritic alloy and austenitic alloy steel tubes

ASTM A 453/A453M Standard specification for high temperature bolting materials, with expansion coefficients comparable to austenitic steels

ASTM A 463/A463M Standard specification for steel sheet, aluminium-coated by hot-dip process

ASTM A 491 Standard specification for aluminium coated steel chain link fence fabric

ASTM A 516/A516M Pressure vessel plates, carbon steel, for moderate and lower-temperature service

ASTM A 522/A522M Forged and rolled 8 and 9% nickel alloy steel flanges, fittings, valves and parts for low-temperature service

ASTM A 525/A525M Specification for general requirements for steel sheet, zinc coated (galvanised) by hot dip process

ASTM A 530 Standard specification for general requirements for specialized carbon and alloy steel pipe

ASTM A 537/A537M Pressure vessel plates, heat treated, carbon-manganese-silicon steel

ASTM A 553/A553M Pressure vessel plates, alloy steel, quenched and tempered 8 and 9 percent nickel

ASTM A 609 Specification for Longitudinal-Beam Ultrasonic Inspection for Carbon and Low-alloy Steel Castings

ASTM A671 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures

ASTM A672 Standard Specification for Electric-Fusion-Welded Steel Pipe for High Pressure Service at Moderate Temperature

ASTM A 765/A765M Carbon steel and low-alloy steel pressure-vessel-component forgings with mandatory toughness requirements

ASTM A 770/A770M Specification for through-thickness tension testing of steel plate for special applications

ASTM A 790/A 790M Standard specification for seamless and welded ferritic/austenitic stainless steel pipe

ASTM A961 Standard Specification for Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High Pressure Service at High Temperature

ASTM B 148 Specification for aluminum bronze sand castings

ASTM B 165 Standard specification of nickel-copper alloy

ASTM B 209 Standard specification for aluminium and aluminium alloy sheet and plate

ASTM B 418 Standard specification for cast and wrought galvanic zinc anodes

ASTM B 423 Standard specification for seamless and electric welded low-alloy steel tubes

ASTM B 574 Standard Specification for Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Chromium-Molybdenum, Low- Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

ASTM B 637 Standard specification for precipitation-hardening nickel alloy bars, forgings, and for going stock for high temperature service

ASTM B 668 Standard specification for UNS N08028 seamless pipe and tube

ASTM B 695 Standard Specification for coatings of zinc mechanically deposited on iron and steel

ASTM B 764-04 (Includes change to title) Test Method for Simultaneous Thickness and Electrode Potential Determination of Individual

Layers in Multilayer Nickel Deposit Step Test (R)

ASTM B 839-04 Test Method for Residual Embrittlement in Metallic coated, externally threaded articles, fasteners, and rod – inclined Wedge Method (R)

ASTM B 851-04 Specification for automated controlled shot peening of metallic articles prior to Nickel, autocatalytic nickel, or chromium plating, or as final finish

ASTM C 27 Standard Classification of Fireclay and High-Alumina Refractory Brick

ASTM C 155 Standard Classification of Insulating Firebrick

ASTM C 165 Standard test method for measuring compressive properties of thermal insulation

ASTM C 167 Standard test method for thickness and density of blanket or batt insulations

ASTM C 177 Standard test method for steady-state heat flux measurements and thermal transmissions properties by means of the guarded hot plate apparatus

ASTM C 240 Standard test method of testing cellular glass insulating block

ASTM C 273 Test for shear properties in flatwise plane or flat sandwich constructions or sandwich cores

ASTM C 303 Standard test method for dimensions and density of performed block-type thermal insulation

ASTM C 390 Criteria for sampling and acceptance of pre formed thermal insulation lots

ASTM C 401 Standard Classification of Alumina and Alumina-Silicate Castable Refractories

ASTM C 461 Standard test method of mastic and coating used in conjunction with thermal insulation

ASTM C 518 Standard test method for steady state heat flux measurements and thermal transmission properties by means of the heat flow meter

ASTM C 533 Standard specification for calcium silicate block and pipe thermal insulation

ASTM C 547 Standard specification for mineral fibre pipe insulation

ASTM C 552 Standard specification for cellular glass thermal insulation

ASTM C 585 Standard practice for inner and outer diameters of rigid thermal insulation for nominal sizes of pipe and tubing (NPS system)

ASTM C 591 Standard specification for unfaced pre formed rigid cellular polyisocyanurate thermal insulation

ASTM C 592 Standard specification for mineral fibre blanket insulation and blanket-type pipe insulation

ASTM C 612 Specification for mineral fibre block and board thermal insulation

ASTM C 623 Standard test method for Young’s modulus, shear modules and Poisson's ratio for glass and glass ceramics by resonance

ASTM C 680 Standard practice for the determination of heat gain or loss and the surface temperatures of insulated pipe and equipment

systems by the use of a computer program

ASTM C 795 Standard specification for thermal insulation for use in contact with austenitic stainless steel

ASTM C 871 Standard test methods for chemical analysis of thermal insulation materials for leachable chloride, fluoride, silicate and sodium ions

ASTM C 876 Standard test method for half cell potentials of uncoated reinforcing steel in concrete

ASTM C 892 Standard specification for high temperature fibre blanket thermal insulation

ASTM C 1497-04 Specification for cellulosic fiber stabilized thermal insulation (R)

ASTM D 312 Standard specification for asphalt used in roofing

ASTM D 420 Guide to site characterization for engineering, design and construction purposes

ASTM D 511 Test method for calcium and magnesium in water

ASTM D 512 Test method for chloride ion in water

ASTM D 513 Test methods for carbon dioxide, total and dissolved, in water

ASTM D 516 Test method for sulphate ion in water

ASTM D 5162 Standard practice for discontinuity (holiday) testing of non-conductive protective coating on metallic substrates

ASTM D 610 Test methods for evaluating degree of rusting on painted steel surfaces

ASTM D 635 Test method for rate of burning and/or extent and time of burning of self-supporting plastics in a horizontal position

ASTM D 653 Terminology relating to soil, rock and contaminated fluids

ASTM D 790 Standard test methods for flexural properties of un-reinforced and reinforced plastics and electrical insulating materials

ASTM D 1066 Practice for sampling steam

ASTM D 1126 Test methods for hardness in water

ASTM D 1248 Specification for polyethylene plastics moulding and extrusion materials

ASTM D 1250 Standard guide for petroleum measurement tables

ASTM D 1293 Test method for pH of water

ASTM D 1426 Test methods for ammonia nitrogen in water

ASTM D 1452 Practice for soil investigation and sampling by auger borings

ASTM D 1557 Standard Test methods for laboratory compaction characteristics of soil using modified effort

ASTM D 1587 Practice for thin-walled tube geotechnical sampling of soils

ASTM D 1621 Standard test method for compressive properties of rigid cellular plastics

ASTM D 1622 Standard test method for apparent density of rigid cellular plastics

ASTM D 1623 Standard test method for tensile adhesion properties of rigid cellular plastics

ASTM D 2487 Standard practice for classification of soils for engineering purposes

ASTM D 2563 Practice for classifying visual defects in glass reinforced plastic laminate parts

ASTM D 2583 Standard test method for indention hardness of rigid plastics by means of barcol impressor

ASTM D 2856 Standard test method for open cell content of rigid cellular plastics by the air pycnometer

ASTM D 3014 Standard test method for flame height, time of burning and loss of mass of rigid thermoset cellular plastics in a vertical position

ASTM D 3039/3039M Test method for tensile properties of polymer matrix composite materials

ASTM D 3370 Practice for sampling water from closed circuits

ASTM D 3441 Deep, quasi-static cone and friction cone penetration tests of soil

ASTM D 3744 Test method of aggregate durability index

ASTM D 3764 Standard practice for validation of process stream analysers

ASTM D 4541 Standard test method for pull and off strength of coating using portable adhesion testers.

ASTM D 5162 Standard practice for discontinuity (holiday) testing of non-conductive protective coating on metallic substrates

ASTM D 6122 Standard practice for the validation of multivariate process infrared spectrophotometers

ASTM E 162 Standard test method for surface flammability of materials using a radiant heat source

ASTM E 21 Elevated temperature tension test of metallic materials

ASTM E 84 Standard test method for surface burning characteristics of building materials

ASTM E 94 Standard guide for Radiographic Testing

ASTM E 96 Standard test method for measurement of water vapour transmission of materials

ASTM E 110 Standard test method for indentation hardness of metallic materials by portable hardness testers

ASTM E 165 Standard test method for liquid penetrant examination

ASTM E 413-04 Classification for Rating Sound Insulation (R)

ASTM E 446 Reference Radiographs for Steel Castings up to 2in. (51mm) in Thickness

ASTM E 709 Standard guide for magnetic particle examination

ASTM E 966-04 Guide for field measurement of airborne sound insulation of building facades and façade elements (R)

ASTM E 1687-04 Test method for Determining Carcinogenic Potential of Virgin Base Oils in Metalworking Fluids (R)

ASTM E 1972-04 Practice for Minimizing Effects of Aerosols in the Wet Metal Removal Environment (R)

ASTM E 2235-04 Test method for determination of decay rates for use in sound insulation test methods (R)

ASTM F 552 Standard terminology relating to chain link fencing

ASTM F 567 Standard practice for installation of chain link fence

ASTM F 668 Standard specification for polyvinyl chloride (pvc) and other organic polymer-coated steel chain link fence fabric

ASTM F 1043 Standard specification for strength and protective coatings on metal industrial chain link fence framework

ASTM F 1249 Test method for water vapour transmission rate through plastic film and sheeting using a modulated infra red sensor

ASTM G 57 Standard test method for field measurement of soil resistivity using Wenner four electrode method

ASTM G 93 Cleaning methods for material and equipment used in oxygen enriched environments

ASTM SI-10 Practice for the use of the International System of units (SI)

ASTM Volume 04.03 Traveled surface characteristics

ASTM Volume 04.08 Natural building stones; Soil and rock

ASTM Volume 11.01 Water (I)

ASTM Volume 11.02 Water (II)

ATEX Directives Protective equipment and systems intended for use in potentially explosive atmospheres;

AWWA M45 Fibreglass Pipe Design- First Edition

AWS A5.1 Specification for covered carbon steel arc welding electrodes

AWS A5.11A5.11M Nickel and nickel alloy welding electrodes for shielded metal arc welding

AWS A5.14/A5.14M Nickel and nickel alloy bare welding electrodes and rods

AWS A5.17/A5.17M Specification for carbon steel electrodes and fluxes for submerged arc welding

AWS A5.18 Specification for carbon steel filler metals for gas shielded arc welding

AWS A5.4 Specification for stainless steel electrodes for shielded metal-arc welding

AWS A5.5 Specification for low alloy steel covered arc welding electrodes

AWS A5.9 Bare stainless steel welding electrodes and rods

AWS D1.1/D1.1M Structural welding code steel

BS 88 Cartridge fuses for voltages up to and including 1000V AC and 1500V DC

BS 171D Identification of Pipe Lines and Services. BSI, UDC (621.643/644) – 777.6

BS 336 Specification for Fire hose couplings and ancillary equipment

BS 381C Colours for Identification, Coding and Special Purposes

BS 417 Specification for galvanised low carbon steel cisterns, cistern lids, tanks and cylinders

BS 449 The use of structural steel in buildings

BS 466 Specification for Power Driven Overhead Travelling Cranes, semi goliath and goliath cranes for general use

BS 476 Fire tests on building materials and structures

BS 476-3 Fire tests on building materials and structures – Part 3: classification and method of test for external exposure to roofs

BS 599 Methods of testing pumps

BS 709 Methods of destructive testing fusion welded joints and weld metal steel

BS 729 Hot dip galvanized coatings on iron and steel articles

BS 743 Specification for Materials for Damp Proof Courses

BS 747 Specification for Reinforced Bitumen Roofing

BS 750 Specification for underground fire hydrants and surface box frames and covers.

BS 812 – 123 Testing aggregates - Method for the determination of Alkali-Silica reactivity - Concrete prism method

BS 848 Fans for general purpose

BS 952 Glass for Glazing

BS 1113 Specification for design and manufacture of water-tube steam generating plant etc

BS 1133 Packaging code

BS 1184 Specification for Copper & Copper Alloy Traps

BS 1188 Ceramic Wash Basins and Pedestals

BS 1191 Specification for Gypsum Building Plasters

BS 1230 Gypsum – Plasterboard

BS 1245 Specification Metal Door Frame (steel)

BS 1253 Gullies for Buildings

BS 1376 Specification for colours of light signals

BS 1377 Methods of tests for soils for civil engineering purposes – parts 1 to 9

BS 1377 Methods of test for soils for civil engineering purposes. Part 3 Chemical and Electrochemical tests, Part 9 In-situ tests.

BS 1414 Specification for steel wedge gate valves (flanged and buttwelding ends) for the petroleum, petrochemical and allied industries

BS 1449 Specification for steel plate, sheet and strip

BS 1494 Specification for fixing accessories for Building Purposes. Fixing for Sheets, Roof and Wall Coverings

BS 1501 Steel for pressure purposes

BS 1503 Specification for steel forgings for pressure purposes

BS 1521 Specification for waterproof building papers

BS 1635 Recommendations for graphical symbols and abbreviations for fire protection drawings

BS 1640 Steel butt-welding pipe fittings for the petroleum industry

BS 1722 Part 10 Fences - Part 10: Specification for anti-intruder fences in chain-link and welded mesh

BS 1726 Coil springs

BS 1787 Steel Windows for Industrial Windows

BS 1868 Specification for steel check valves (flanged and butt welding ends) for the petroleum, petrochemical and allied industries

BS 1873 Specification for steel globe and globe stop valves (flanged and butt welding ends) for the petroleum, petrochemical and allied industries

BS 1876 Specification for Automatic Flush Cisterns for Urinals

BS 1881 Testing concrete

BS 1990-1 Wood poles for overhead power and telecommunications lines

BS 2000 – Part 72 'Methods of test for petroleum and its products Part 72 - Determination of viscosity of cutback bitumen'

BS 2080 Specification for face to face, centre to centre, end to end and centre to end dimensions of valves

BS 2573 Rules for the design of cranes

Part 1 Specification for classification, stress calculations and design criteria for structures

Part 2 and AMD 3952 and AMD 5013 Specification for classification, stress calculations and design of mechanisms

BS 2654 Specification for manufacture of vertical steel welded non-refrigerated storage tanks with butt welded shells for the petroleum industry

BS 2690 Methods of testing water used in industry

BS 2853 The design and testing of steel overhead runway beams

BS 2972 Methods of test for inorganic thermal insulating materials

BS 2997 Specification for Aluminium Rainwater Goods

BS 3083 Specification for Hot Dipped and Hot Dipped Aluminium/Zinc Coated corrugated steels sheets for general purposes

BS 3148 Methods of test for water and making concrete

BS 3165 Specification for rubber and plastics suction hoses and hose assemblies for fire-fighting purposes

BS 3381 Spiral Wound Gaskets for Steel Flanges to BS 1560

BS 3402 Specification for Quality Vitreous China Sanitary Appliances

BS 3505 Specification for unplasticized polyvinyl chloride (U-PVC) pressure pipes for cold potable water

BS 3573 Specification for polyolefin copper conductor telecommunication cables

BS 3602 Specification for steel pipes and tubes for pressure purposes; carbon and carbon manganese steel with specified elevated temperature properties

BS 3603 Specification for carbon and alloy steel pipes and tubes with specified low temperature properties for pressure purposes

BS 3605 Austenitic Stainless steel pipes and tubes for pressure purposes

BS 3606 Specification for steel tubes for heat exchangers

BS 3621 Specification for Thief Resistant Locks

BS 3790 Specification for endless wedge belt drives and endless V-belt drives

BS 3958 Thermal insulating material

BS 3974 Specification on pipe supports

BS 4022 Specification for pre-fabricated gypsum plasterboard

BS 4027 Specification for sulphate resisting Portland cement

BS 4076 Steel Chimneys

BS 4082 External dimensions for vertical in-line centrifugal pumps.

BS 4131 Terrazzo Tiles

BS 4211 Specification for ladders for permanent access to chimneys, other high structures, silos and bins

BS 4320 Specification for metal washers for general engineering purposes

BS 4346 Joints and fittings for the use with unplasticized PVC pressure pipes

BS 4370 Methods of test for rigid cellular materials

BS 4449 Carbon steel bars for the reinforcement of concrete

BS 4483 Steel fabric for the reinforcement of concrete

BS 4514 Un-plasticised PVC Soil and Ventilation Pipes of 82.4mm mean outside diameter and accessories of 82.4mm and other sizes

BS 4721 Specification for Ready Mixed Building Mortars

BS 4735 Laboratory methods of tests for the assessment of the horizontal burning characteristics of specimens no larger than 150mm x 50mm x 13mm of cellular plastics and cellular rubber materials when subjected to a small flame

BS 4787 Internal and External Wood door sets, door leaves and frames

BS 4800 Schedule of paint colours for building purposes

BS 4868 Profiled Aluminium Sheet for Buildings

BS 4880 Urinals, Stainless Steel Slab Urinals

BS 4882 Specification for bolting for flanges and pressure containing purposes

BS 4991 Specification for propylene copolymer pressure pipe

BS 4999-140 General requirements for rotating electrical machines

BS 4999-144 General requirements for rotating electrical machines Part 144: Specification for the insulation of bars and coils of high

voltage machines, including test methods

BS 5041-1 Fire hydrant systems equipment-Specification for landing valves for wet risers

BS 5041-2 Fire hydrant systems equipment-Specification for landing valves for dry risers

BS 5051 Specification for Security Glazing

BS 5135 and AMD 5172 Specification for arc welding of carbon and carbon manganese steels

BS 5224 Masonry Cement

BS 5234 Partitions (including Matching Linings)

BS 5250 Code of Practice for the Control of Condensation in Buildings

BS 5262 Code of Practice for External Rendered Finishes

BS 5306 Part 0 Guide for the Selection of Installed Systems and Other Fire Equipment

BS 5306 Part 1 Hydrant Systems, Hose Reels and Foam Inlets

BS 5306 Part 2 Specification for Sprinkler Systems

BS 5306 Part 4 Specification for Carbon Dioxide Systems

BS 5306 Section 6.1 Specification for Low Expansion Foam Systems

BS 5306 Section 6.2 Specification for Medium and High Expansion Foam Systems

BS 5306 Part 7 Specification for Powder Systems

BS 5308 Instrumentation cables

BS 5351 Specification for Steel Ball Valves for the Petroleum, Petrochemical and Allied Industries

BS 5352 Specification for steel wedge gate, globe and check valves 50mm and smaller for the petroleum, petrochemical and allied industries

BS 5353 Steel plug valves

BS 5357 Code of Practice for Installation of Security Glazing

BS 5368 Methods for Testing Windows

BS 5385 Code of Practice for the Design and Installation of Ceramic Floor, Wall Tiles and Mosaics

BS 5395 Part 2 Code of Practice for the Design of Helical & Spiral Stairs

BS 5395 Part 3 Code of Practice for the Design of Industrial Type Stairs, permanent ladders and walkways

BS 5422 Methods for specifying thermal insulating materials on pipes, ductwork and equipment (in the temperature range-40°C to+700°C)

BS 5427 Code of Practice for use of profiled sheet for roof and wall cladding on buildings

BS 5492 Code of Practice for Internal Plastering

BS 5499 Code of Practice for Escape Signs, Route Signage, Safety Signs including Fire Safety Signs

BS PD 5500 Specification for unfired fusion welded pressure vessels

BS 5503 Specification for Vitreous China washdown WC pans with horizontal outlet

BS 5504 Specification for wall hung WC pans

BS 5506 Specification for wash basins

BS 5520 Specification for Vitreous chain bowl urinals (rimless type)

BS 5588 Fire Precautions in the Design, Construction and Use of Buildings

BS 5628 Code of Practice for the structural use of Masonry

BS 5642 Sills and Copings, Specification for Sills and Copings of Pre-Cast Concrete, Cast Stone, Clay ware, Slate & Natural Stone

BS 5713 Specification for Hermetically sealed flat double glazing units

BS 5731-4 Specification for aluminium and aluminium alloy

BS 5744 Code of practice for safe use of cranes

BS 5750 Quality systems

BS 5872 Specification for locks and latches for doors in Buildings

BS 5977 Lintels – Method of Assessment of Loads

BS 5930 Code of practice for site investigation

BS 5950 Structural use of steelwork in building

BS 5970 Code of practice for thermal insulation of pipework and equipment (in the temperature range of -100oC to +870oC)

BS 5996 Ultrasonic testing and specifying quality grades of ferritic steel plate

BS 6072 and AMD 3960, Method for magnetic particle flaw detection 4542 and 4843

BS 6073 Pre-cast Masonry Units

BS 6100 Part 1 Glossary of building and civil engineering terms - Part 1: General and miscellaneous

BS 6100 Part 2 Glossary of building and civil engineering terms - Part 2: Civil engineering

BS 6150 Code of Practice for Painting of Buildings

BS 6031 Code of practice for earthworks'

BS 6121 Specification for mechanical cable glands

BS 6217 Code of Practice for Built up felt roofing

BS 6218 Code of Practice for Mastic Asphalt Roofing

BS 6229 Code of Practice for Flat Roofs with continuously supported covering

BS 6231 Specification for PVC-insulated cables for switchgear and control gear wiring

BS 6259 Code of Practice for the design, planning, installation, testing and maintenance of sound systems

BS 6262 Code of Practice for Glazing of Buildings

BS 6290-4 Lead-acid stationary cells and batteries

BS 6349 Code of practice for maritime structures - Part 1 through Part 7

BS 6364 Specification for valves for cryogenic service

BS 6375 Performance of Windows

BS 6387 Specification for performance requirements for cables required to maintain circuit integrity under fire conditions

BS 6398 Specification for Bitumen Damp-proof Courses for Masonry

BS 6399-1 Loading for buildings – Part 1 Code of Practice for dead and imposed loads

BS 6399-2 Loading for buildings – Part 2 Code of Practice for wind loads

BS 6399-3 Loading for buildings – Part 3 Code of Practice for imposed roof loads

BS 6431 Ceramic Floor and Wall Tiles

BS 6437 Specification for polyethylene pipes (type 50) in metric diameters for general purposes

BS 6452 Beads for Internal Plaster & Dry Linings

BS 6467 Electrical Apparatus with protection by enclosure for use in the presence of combustible dusts

BS 6510 Specification for steel windows, sills, window boards and doors

BS 6510 Steel sub-frames, sills & window boards for metal windows

BS 6515 Specification for Polyethylene Damp Proof Courses for Masonry

BS 6572 Specification for Blue Polyethylene pipes up to nominal size 63 for below ground use for portable water

BS 6651 Code of practice for protection of structures against lightning

BS 6656 Guide to prevention of inadvertent ignition of flammable atmosphere by radio frequency radiation

BS 6701 Telecommunications equipment and telecommunications cabling – specification for installation, operation and maintenance.

BS 6730 Specification for black polyethylene pipes up to nominal size 63 for above ground use for cold potable water

BS 6755 Inspection and testing of valves. Parts 1 and 2

BS 6883 Elastomer insulated cables for fixed wiring in ships and on mobile and fixed offshore units

BS 6941 Specification for electrical apparatus for explosive atmospheres with type of protection N

BS 6925 Specification for Mastic Asphalt for Building & Civil Engineering

BS 7121 Code of practice for safe use of cranes.

Part 1 and AMD 9093 General

Part 2 Inspection testing and examination

BS 7281 Specification for polyethylene pipes for the supply of gaseous fuels

BS 7354 Code of practice for design of high-voltage open terminal stations

BS 7357 7.5 litre WC flushing cistern

BS 7361-1 Cathodic Protection

BS 7364 Specification for Galvanised Steel Studs and Channels for Stud and Sheet Partitions using Screw Fixed Gypsum Wallboard

BS 7953 Entrance Flooring Systems, Selection, Installation and Maintenance

BS 8004 Code of practise for Foundations

BS 8007 Code of practice for design of concrete structures for retaining aqueous liquids

BS 8102 Code of Practice for the Protection of Structures Against Water from the Ground

BS 8110 Structural use of concrete

BS 8203 Code of Practice for Installation of Resilient Floor Coverings

BS 8204 Screeds, Bases and In-situ Flooring, Concrete Bases and Cement Sand, Screed to Receive Flooring

BS 8207 Code of Practice for Energy Efficiency in Buildings

BS 8212 Code of Practice for Dry Lining and Partitions using Gypsum Plasterboard

BS 8214 Fire Door assemblies with non-metallic leaves

BS 8215 Code of Practice for Design and Installation of Damp-proof Courses in Masonry Construction

BS 8217 Code of Practice for Built-up Felt Roofing

BS 8218 Code of Practice for Mastic Asphalt Roofing

BS 8290 Code of Practice for Suspended Ceilings

BS 8300 Design of Buildings and their approaches to meet the needs of Disabled People

BS 8500-1 Concrete - Complimentary British Standard to BS EN 206-1 - Method of specifying and guidance for the specification'

BS 8500-2 Concrete - Complimentary British Standard to BS EN 206-1 - Specification for constituent materials and concrete

BS DD IEC TS 60695 Fire Hazard Testing – Part 7-3: Toxicity of Fire Effluent – Use and Interpretation of Test Results

BS EN 179 Building Hardware – Emergency Exit Device Operated by a Lever or Push Pad

BS EN 196 Method for testing concrete

BS EN 197-1 Cement, specification and conformity for common cements

BS EN 206 Concrete, specification, performance, production and compliance and conformity

BS EN 274 Waste Fitting for Sanitary Appliances

BS EN 295 Vitrified Clay Pipes and Fittings

BS EN 329 Sanitary Tapware Waste Fittings for Showers

BS EN 403 Respiratory protective devices for self-rescue – Filtering devices with hood for escape from fire – requirements, testing, marking

BS EN 411 Sanitary Tapware Waste Fittings for Sinks

BS EN 508 Roofing Products for Metal Sheet – Specification for Self Supporting Products of Steel, Aluminium or Stainless Steel Sheet

BS EN 593 Specification for butterfly valves

BS EN 607 Eaves gutters and fittings made from PVC-U

BS EN 612 Eaves gutters and rainwater down pipes of metal sheet

BS EN 649 Resilient Floor Coverings – Homogeneous & Heterogeneous Polyvinyl Chloride Floor Coverings

BS EN 654 Resilient Floor Coverings – Semi-flexible Polyvinyl Chloride Tiles

BS EN 764-1 Pressure Equipment Part 1: Terminology – pressure, temperature, volume, nominal size

BS EN 806 Specification for Installation inside buildings conveying water for human consumption

BS EN 837-1 Specification for bourdon tube pressure and vacuum gauges

BS EN 877 Cast Iron Pipes and Fittings, their joints and accessories for the Evacuation of Water from Buildings

BS EN 934 Admixtures for concrete

BS EN 997 WC Pans and WC Suites with Integral Traps

BS EN 998 Specification for Mortar for Masonry

BS EN 1008 Mixing water for concrete

BS EN 1011 Parts 1 & 2 Welding. Recommendations for welding of metallic materials.

Part 1 General welding for arc welding

Part 2 Arc welding of ferritic steels

BS EN 1057 Copper and Copper Alloys – Seamless Round for Water and Gas in Sanitary and Heating Applications

BS EN 1063 Glass in Buildings – Security Glazing – Testing and Classification of Resistance against Bullet Attack

BS EN 1125 Building Hardware – Panic Exit Devices Operated by a Horizontal Bar

BS EN 1154 Controlled Door Closing Devices

BS EN 1158 Building Hardware – Door Co-ordinator Devices

BS EN 1254 Copper and Copper Alloys – Plumbing Fittings or Capillary Brazing to Copper Tubes, Manufacturers Association

BS EN 1303 Building Hardware – Cylinders for Locks

BS EN 1329 Plastic Piping Systems for Soil and Waste Discharge

BS EN 1451 Plastic Piping Systems for Soil and Waste Discharge within Buildings

BS EN 1452 Plastic Piping Systems for Water Supply

BS EN 1455 Plastic Pipe Systems for Soil and Waste (Low and High Temperature) Within the Building – Acrylonitride Butadiene-Styrene

(APS) Specification for Pipes, Fittings and the System

BS EN 1492-4 Textiles Slings – Safety Part 4: Lifting Slings for general service made from natural and man made fibre ropes

BS EN 1514-7 Flanges and their joints – Gaskets for PN-designated flanges Part 7: covered metal jacketed gaskets for use with steel flanges

BS EN 1519 Plastic Piping Systems for Soil and Waste Discharge (Low and High Temperature) Within the Building Structure –

Polyethlene (PE) Specification for Pipes, Fittings and the System

BS EN 1527 Building Hardware – Hardware for Sliding and Folding Doors

BS EN 1565 Plastic Piping System for Soil and Waste Discharge (Low and High Temperature) Within the Building. Styrene Copolymer

Blends (SAN + PVC) Specification for Pipes Fittings and the System

BS EN 1566 Plastic Piping Systems for Soil and Waste (Low and High Temperature) within the Building Structure – Chlorinated Poly

(Vinyl Chloride) (PVC-c) Specification for Pipes, Fittings and the System

BS EN 1670 Building Hardware – Corrosion Resistance

BS EN 1634 Fire Resistance Tests for Door and Shutter Assemblies, Fire Doors and Shutters

BS EN 1906 Building Hardware – Lever Handles and Knob Furniture

BS EN 1935 Building Hardware – Single Axis Hinges

BS EN 1982 Specification for copper alloy ingots and copper alloy and high conductivity copper castings

BS EN 10160 Ultrasonic testing of steel flat product of thickness equal to or greater than 6mm(reflection method)

BS EN 10223 Specification for zinc-coated hexagonal steel wire netting

BS EN 12051 Building Hardware – Door and Window Bolts

BS EN 12056 Gravity Drainage Systems Inside Buildings BS1184 Specification for Copper and Copper Alloy Traps

BS EN 12056 Part 3 Gravity drainage systems inside buildings – roof drainage layout and calculation

BS EN 12350 Testing fresh concrete

BS EN 12350-2 Testing fresh concrete – slump test

BS EN 12390 Testing Hardened Concrete

BS EN 12390-3 Testing hardened concrete – strength of test specimens

BS EN 12445 Industrial, Commercial & Garage – Doors and Gates

BS EN 12620 Aggregates for concrete

BS EN 12635 Industrial, Commercial and Garage Doors and Gates – Installation and Use

BS EN 12639 Liquid Pumps and Pump Units – Noise Test Code/Grade 2 and grade 3 of Accuracy

BS EN 12680-2 Founding. Ultrasonic examination of Steel castings for highly stressed components

BS EN 12810-1 Façade Scaffolds made of Prefabricated Components – Part 1: Products Specifications

BS EN 12810-2 Façade Scaffolds made of Prefabricated Components – Part 2: Particular Methods of Structural Design

BS EN 12811-1 Temporary Works Equipment – Part 1: Scaffolds – Performance Requirements and General Design

BS EN 12825 Raised Access Floors

BS EN 12952 Water-tube boilers

BS EN 13024 Glass in Building – Thermally Toughened Borosilicate Safety Glass

BS EN 13124 Windows, Doors and Shutters Explosion Resistant

BS EN 13139 Aggregate for Mortar

BS EN 13162 Thermal Insulation products for buildings – Factory made mineral wool

BS EN 13163 Thermal Insulation products for buildings – Factory made products of expanded polystryrene

BS EN 13164 Thermal Insulation products for buildings – Factory made products of extruded polystyrene

BS EN 13310 Kitchen Sinks

BS EN 13553 Resilient Floor Coverings – Polyvinyl Chloride Floor Covering for use in special wet areas

BS EN 13586 Cranes - Access

BS EN 13813 Screed Material and Floor Screeds

BS EN 13892-3 Methods of Test for Screed Materials Part 3: Determination of Wear Resistance

BS EN 14329 Inland Navigation Vessels – Installation of Berths and Loading Areas

BS EN 50054 Electrical apparatus for the detection of combustible gases, general required test methods

BS EN 50055 Electrical apparatus for the detection of combustible gases, performance requirements for group I apparatus indicating up to 5% (V/V) methane in air.

BS EN 50056 Electrical apparatus for the detection of combustible gases, performance requirements for group I apparatus indicating up to 100% (V/V) methane in air.

BS EN 50174 Part 2 Information Technology – Cable Installation – Installation Planning and Practices inside Buildings

BS EN 55022 Radio disturbance characteristics information technology equipment

BS EN 60076-10 Determination of transformer and reactor sound levels

BS EN 60534-8 Industrial - process control valves Part 8: Noise considerations

BS EN 60651 Specification for Sound Level Meters

BS EN 60849 Sound systems for emergency purposes

BS EN 60947 Specification for degrees of protection of enclosures of switchgear and control-gear for voltages up to 1000V AC and 1200V DC

BS EN 61000 Electromagnetic compatibility (EMC)

BS EN 61496-1 Safety of Machinery – Electro-Sensitive Protective Equipment – Part 1: General Requirements and Tests

BS EN ISO 1461 Hot dip galvanised coatings on fabricated iron and steel articles – Specifications and test methods

BS EN ISO 4126-1 Safety devices for protection against excessive pressure – Part 1: Safety valves

BS EN ISO 5667-19 Water Quality – Sampling – Part 19: Guidance on sampling in marine sediments

BS EN ISO 9000 Quality management systems – Fundamentals and vocabulary

BS EN ISO 9001 Quality management systems - Requirements

BS EN ISO 9002 Quality assurance

BS EN ISO 10204 Metallic Products – Types of Inspection Documents

BS EN ISO 14692 Parts 1-4 Petroleum and Natural Gas Industries – Glass Reinforced Plastics (GRP) Piping

BS EN ISO 15465 Pipework – Strip Wound Metal Hoses and Hose Assemblies

BS EN ISO 15614-1 Specification and Qualification of Welding Procedures for Metallic Materials – Welding procedure test Part 1: Arc and Gas

Welding of Steels and Arc Welding of Nickel and Nickel Alloys

BS ISO 4308 Cranes and lifting appliances-Selection of wire ropes

BS ISO 15175 Soil Quality – Characterization of Soil Related to Ground Water Protection

BS PD 5304 Safe use of machinery

CEB-FIP Model code for concrete structures

CEMA 300 Screw conveyor dimensional standards

CEMA 350 Screw conveyors

CEN EN 1822-1 High Efficiency Air Filters (HEPA & ULPA)

CGA/GAS 02-DIR Directory of cleaning agents for oxygen service

CICIND Manual for inspection and maintenance of brickwork and concrete chimneys

CICIND Model code for steel chimneys

CINI Handbook for insulation - Issued by: Commission of the Dutch insulation industrie, Ceintuurbaan 182, 1403 AK, Bussum, The Netherlands

CONCAWE No. 2/79 Method for Determining the Sound Power Levels of Flares Used in Refineries, Chemical Plants and Oilfields

CONCAWE No. 3/77 Test Method for the measurement of noise emitted by furnaces for use in the petroleum and petrochemical industry

CONCAWE Report 87/59 The predictions of noise radiated from pipe systems, an engineering procedure for plant design.

CSA 22.2 – 157 Intrinsincally safe and non-incendive equipment for use in hazardous locations

CSA 22.2 – 30 Explosion-proof enclosures for use in Class 1 hazardous locations general instruction No 1-2R

DIN 0875 Radio interference suppression of electrical appliances and systems

DIN 3852 Part 2 Stud-ends and tapped holes with pipe thread for use with compression couplings

DIN 4030 Evaluation of liquids, soils and gases aggressive to concrete

DIN 19234 Measurement and control; electrical distance sensors; DC interface for distance sensor and signal converter

DIN 45635-22 Measurement of Airborne Noise Emitted by Machines; Enveloping Surface Method, Flares

DIN 45635-47 Measurement of noise emitted by machines: Airborne noise emission Enveloping surface method Chimneys

DIN 45681 Detection of tonal components of noise and determination of a tone adjustment for the assessment of noise emissions

DIN 50129 Testing of metallic materials, testing of welding filler materials for liability to cracking

DIN EN 1870-12 Safety of Woodworking Machines – Circular Sawing Machines – Part 12. Pendulum Cross-cut Sawing Machines EURO 123.30

DIN EN 10204 Inspection documents for the delivery of metallic products

DIN EN 50277 Measurement and control, electrical distance sensors, DC interface for distance sensor and signal converter

DIN EN ISO 15607 Specification and Qualification of Welding Procedures for Metallic Materials – General Rules supercedes DIN EN 288-1 Edn. EURO 94.70

DIN RP-B401 Cathodic Protection Design

DIN V 19250 Control technology; Fundamental safety aspects to be considered for measurement and control equipment

DIN VDE 0801 Principle for computers in safety related systems

DIN VDE 0101 Erection of power installations with rated voltages exceeding 1 kV

EEMUA Pub. 106 General specification for silencers and acoustic enclosures

(Formerly OCMA NWG-4, 1979), replaced by EEMUA Pub. 161

EEMUA Pub. 132 Specification of 3 phase cage induction motors

EEMUA Pub. 140 Noise procedure specification (Formerly OCMA NWG-1, Rev. 2, 1980)

EEMUA Pub. 142 Acoustic insulation of pipes, valves and flanges (formerly OCMA NWG-5, 1982)

EEMUA Pub. 143 Recommendations for tube-end welding, tubular heat transfer equipment. (Formerly OCMA specification No. TEW 1)

EEMUA Pub. 161 Guide to selection and assessment of silencers and acoustic enclosures

EEMUA Pub. 201 Process plant control desks utilising human-computer interfaces – A guide to design, operational and human interface issues.

EIA RS 232,422 & 485 Interface between data terminal equipment and data communication equipment employing serial binary data

EIA/TIA 222 Structural standards for steel antenna towers and antenna supporting structures

EIA/TIA 232 Interface between data terminal equipment and data communication equipment

EIA/TIA 422 Electrical characteristics of balanced voltage digital interface circuits

EIA/TIA 423 Electrical characteristics of unbalanced voltage digital interface circuits

EIA/TIA 455 Standard Test procedures for fibre optic fibres, cables, transducers, connecting and terminating devices

EIA/TIA 568 Commercial building telecommunications cabling standard

EIA/TIA 569 Commercial building standard for telecommunications pathways and spaces

EIA/TIA 606 Administration standard for the telecommunications infrastructure of commercial buildings

EJMA Standards of the Expansion Joint Manufacturers Association

EN 54 Fire protection and fire alarm system

EN 81 Safety rules for the construction and installation of lifts and service lifts

EN 287 Approval testing of welders for fusion welding

EN 288 Approval of welding procedures for metallic materials

EN 292 Safety of machinery - Basic concepts, general principles for design

EN 294 Safety of machinery - Safety distances to prevent danger zones to be reached by upper limbs

EN 349 Safety of machinery - Minimum gaps to avoid crushing parts of the human body

EN 563 Safety of machinery - Temperature of touchable surfaces - Ergonomics data to establish temperature limit values for hot surfaces

EN 571 Part 1 Non destructive testing – penetrant testing Part 1: General principles

EN 614 Safety of machinery - Ergonomic design principles

EN 837 -1 Pressure Gauges, Part 1: Bourdon tube pressure gauges. Dimensions, metrology, requirements and testing

EN 1043-1 Destructive tests on welds in metallic materials. Hardness testing. Hardness test on arc welded joints

EN 1418 Welding personnel. Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials

EN 1964 Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and including 150 litres

EN 10028 Flat products made of steel for pressure purposes

EN 10164 Steel products with improved deformation properties perpendicular to the surface of the product; technical delivery conditions

EN 10204 Metallic products - Type of inspection documents

EN 41003 Particular safety requirements for equipment to be connected to telecommunications networks

EN 50014 Electrical apparatus for potentially explosive atmospheres - General requirements

EN 50015 Electrical apparatus for potentially explosive atmospheres - Oil immersion

EN 50016 Electrical apparatus for potentially explosive atmospheres - Pressurized apparatus

EN 50017 Electrical apparatus for potentially explosive atmospheres - Powder filling

EN 50018 Electrical apparatus for potentially explosive atmospheres - Flameproof enclosure

EN 50019 Electrical apparatus for potentially explosive atmospheres - Increased safety

EN 50020 Electrical apparatus for potentially explosive atmospheres - Intrinsic safety

EN 50021 Type of Protection ‘n’

EN 50028 Electrical apparatus for potentially explosive atmospheres - Encapsulation 'm'

EN 50039 Electrical apparatus for potentially explosive atmospheres – intrinsically safe electrical systems ‘I’

EN 50057 Electrical apparatus for the detection and measurement of combustible gases; performance requirements for group II apparatus indicating up to 100% lower explosive limit

EN 50058 Electrical apparatus for the detection and measurement of combustible gases; performance requirements for group II apparatus indicating up to 100% (v/v) gas

EN 50081 Electromagnetic compatibility - Generic emission standard

EN 50082 Electromagnetic compatibility - Generic immunity standard

EN 50091-2 Uninterruptible Power Systems (UPS)

EN 50160 Voltage characteristics of electricity supplied by public distribution systems

EN 50174 Information technology cable installation

EN 50209 1999 Test of Insulation of Bars and Coils of High-Voltage Machines Supersedes BS 4999-144; 1987 (F)

EN 55011 Limits and methods of measurement of radio interference characteristics of industrial, scientific and medical (ISM) radiofrequency equipment

EN 55011M Limits and methods of measurement of radio disturbance characteristics of industrial, scientific and medical radio frequency equipment

EN 55022 Limits and methods of measurement of radio interference characteristics of information technology (ITE) equipment

EN 61000-4-5 Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques – Section 5: Surge Immunity Test

EN 61779 Parts 1 to 5 Electrical apparatus for the detection and measurement of flammable gases. Part 1: General requirements and test methods

Part 2: Performance requirements for group I apparatus indicating a volume fraction up to 5 % methane in air

Part 3: Performance requirements for group I apparatus indicating a volume fraction up to 100 % methane in air

Part 4: Performance requirements for group II apparatus indicating a volume fraction up to 100 % lower explosive limit

Part 5: Performance requirements for group II apparatus indicating a volume fraction up to 100 % gas

EN 187101 Optical telecommunications cables to be used in ducts or direct buried application

ERA 69-30 Current rating standards for distribution cables

FM 3610 Intrinsically safe apparatus and associated apparatus for us n Class 1, 11 & 111, Division 1, and Class 1, Zone 0 & 1

Hazardous (classified) locations

FM 3615 Explosion-proof electrical equipment – general requirements

FIP Guide to good practice grouting of tendons in pre stressed concrete

FIP Recommendations for the acceptance of post-tensioning systems

HEI Steam surface condensers and addendum 1 Steam Jet Vacuum Systems

HTFS Handbook sheet JMI Allowing for fouling in heat exchanger design

ICAO Annex 14 Regulations

ICAO July 1990 Annex 14 to the Convention on International Civil Aviation Aerodromes

IEC 34-9 Rotating Electrical Machines – Part 9: Noise Limits

IEC 225 Specification for Octave-Band and Fractional-Octave-Band-Analogue and Digital Filters

IEC 651 Recommendations for Sound Level Meters

IEC 60034 Rotating electrical machines

IEC 60038 IEC standard voltages

IEC 60044 Current Transformers

IEC 60044-1 Current Transformers

IEC 60044-2 Voltage Transformers

IEC 60050 International electrotechnical vocabulary - Electrical installations of buildings

IEC 60051 Direct acting indicating analogue electrical measuring instruments and their accessories

IEC 60056 High voltage alternating-current circuit-breakers

IEC 60060 High voltage test techniques

IEC 60068 Environmental testing

IEC 60071 Insulation coordination

IEC 60072 Dimensions and output ratings for rotating electrical machines

IEC 60073 Basic and safety principles for man-machine interface, marking and identification, indicating devices and actuators

IEC 60076 Power transformers

IEC 60079 Electrical apparatus for explosive gas atmospheres

IEC 60085 Method for Determining the Thermal Classification of Electrical Insulation

IEC 60096 Radio Frequency Cables

IEC 60099-1 Lightning arresters Part 1 – Non linear resistor type arrestor for a.c systems

IEC 60112 Method for determining the comparative and the proof-tracking indices of solid insulating material under moist conditions

IEC 60113 Diagrams, charts, tables

IEC 60120 Dimensions of ball and socket couplings of string insulator units

IEC 60137 Bushing for alternating voltages above 1000V

IEC 60146 Semiconductor converters

IEC 60156 Method for the determination of the electric strength of insulating oils

IEC 60157 Low Voltage Switchgear and Control Gear

IEC 60158 Specification for Control Gear for Voltages up to and including 1000VAC &1200VDC

IEC 60168 Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater that 1000V

IEC 60204 Electrical equipment of industrial machines

IEC 60214 On-load tap-changers

IEC 60225 Octave, half-octave and third-octave band filters intended for the analysis of sound and vibrations, replaced by IEC 61265

IEC 60227 Polyvinyl chloride insulated cables of rate voltages up to including 450/750 V

IEC 60255 Electrical relays

IEC 60265 High-voltage switches

IEC 60269 Low voltage fuses

IEC 60282 High voltage fuses

IEC 60289 Reactors

IEC 60296 Specification for unused Mineral Oils for Transformers and Switchgear

IEC 60292 Low Voltage Motor Starters

IEC 60298 AC metal-enclosed switchgear and control-gear for rated voltages above 1kV and up to and including 52kV

IEC 60300 Reliability and maintainability management

IEC 60304 Standard colours for insulation for low-frequency cables and wires

IEC 60309 Plugs, socket-outlets and couplers for industrial purposes

IEC 60317 Specifications for particular types of winding wires;

IEC 60331 Fire resisting characteristics of electric cable

IEC 60332 Tests on electric cables under fire conditions

IEC 60364 Electrical installation of buildings

IEC 60383 Tests on insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1000 V

IEC 60398 General test conditions for industrial electroheating equipment

IEC 60408 Low Voltage Air-Break Switches, Air-Break De-connectors, Air-Break Switches, De-connectors and Fuse-Combination Units

IEC 60422 Maintenance and supervision guide for insulating oils in service

IEC 60433 Characteristics of string insulator units of the long rod type

IEC 60439 Low voltage switchgear and control gear assemblies

IEC 60445 Identification of apparatus terminals and general rules for a uniform system of terminal marking, using an alpha-numeric notation

IEC 60470 High voltage a.c contactors

IEC 60473 Dimensions for panel mounted indicating and recording electrical measuring instruments

IEC 60478 Stabilized power supplies, DC output

IEC 60493-1-1992 Low voltage switchgear and control gear assemblies, Part 1: Type tested and partially type tested assemblies

IEC 60521 Class 0.5, 1 & 2 alternating current watt hour meters

IEC 60529 Electrical apparatus ingress protection

IEC 60534 Industrial process control valves – Part 8 noise considerations

IEC 60542 Application guide for on load tap changers

IEC 60549 High voltage fuses for the external protection of shunt power capacitors

IEC 60551 Determination of transformer and reactor sound levels

IEC 60584 Thermocouples

IEC 60593 Internal fuses and internal overpressure disconnectors for shunt capacitors

IEC 60605 Equipment reliability testing

IEC 60617 Graphical symbols for diagrams

IEC 60623 Vented nickel-cadmium prismatic rechargeable single cells

IEC 60654 Operating conditions for industrial-process measurement and control equipment

IEC 60688 Electrical measuring transducers for converting a.c electrical quantities to analogue or digital signals

IEC 60694 Common specifications for high voltage switchgear and control gear standards

IEC 60695 Fire Hazard Testing –Part 7-1: Toxicity of Fire Effluent – General Guidance

IEC 60721-2-1 Classification of Environmental Conditions

IEC 60726 Dry-type power transformers

IEC 60742 Isolating transformers and safety isolating transformers

IEC 60751 Industrial platinum resistance thermometer sensors

IEC 60794 Optical fibre cables

IEC 60801 Electromagnetic compatibility for industrial process measurement and control equipment

IEC 60815 Guide for the selection of insulators in respect of polluted conditions

IEC 60831 Shunt power capacitors of the self-heating type for a.c systems having a rated voltage up to and including 1kV

IEC 60849 Sound Systems for Emergency Purposes

IEC 60851 Winding wires – test methods

IEC 60871 Shunt capacitors for a.c power systems having a rated voltage above 1kV

IEC 60894 Guide for test procedure for the measurement of loss tangent on coils and bars for machine windings

IEC 60896 Stationary lead-acid batteries, general requirements and methods of test

IEC 60898 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations

IEC 60902 Industrial process measurement and control terms and definitions

IEC 60905 Loading guide for dry-type power transformers

IEC 60909 Short-circuit calculation in three-phase AC systems

IEC 60947 Low voltage switchgear and control gear

IEC 61000 Electromagnetic compatibility (EMC)

IEC 61024 Protection of structures against lightning

IEC 61078 Analysis techniques for dependability – Reliability block diagram method

IEC 61089 Round wire concentric lay overhead electrical stranded conductors

IEC 61099 Specification for unused synthetic organic esters for electrical purposes

IEC 61131 Programmable controllers

IEC 61241 Electrical apparatus for use in the presence of combustible dust

IEC 61285 Industrial-process control - safety of analyser houses

IEC 61293 Marking of electrical equipment with ratings related to electrical supply - Safety requirements

IEC 61481 Live Working – Portable Phase Comparators for Use on Voltages from 1kV to 36 kV a.c

IEC 61508 Functional safety of electrical/electronic/programmable electronic safety related systems

IEC 61511 Functional safety: safety instrumented systems for the process industry sector

IEC 61518 Mating dimensions between differential pressure (type) measuring instruments and flanged-on shut-off devices up to 413 bar

IEC 61634 High voltage switchgear and control gear - Use and handling of sulphur hexafluoride (SF6) in high voltage and control gear

IEC 61641 Guide for testing under conditions of arcing due to internal fault

IEC 61850 Communications networks and systems in substations

IEC 62086-1IEC 62086-1 Electrical apparatus for explosive gas atmospheres

IEC/CISPR 11 Limits and methods of measurement of radio disturbance characteristics of industrial, scientific and medical (ISM) radiofrequency equipment

IEC/CISPR 14 Limits and methods of measurement of radio disturbance characteristics of electric motor-operated and thermal appliances

for household and similar purposes, electric tools and similar electric apparatus

IEC/CISPR 22 Limits and methods of measurement of radio interference characteristics of information technology (ITE) equipment

IEEE 80 Guide for Safety in AC Substation Grounding

IEEE 115 Guide: Test procedures for synchronous machines

IEEE 421.2 Guide for identification, testing, and evaluation of the dynamic performance of excitation control systems

IEEE 421.5 Recommended practice for excitation system models for power system stability studies

IEEE 519 Recommended practices and requirements for harmonic control in electrical power systems

IEEE 802 Standards for local and metropolitan area networks

IGC 33/97/E Cleaning of equipment for oxygen service (EIGA – European Industrial Gases Association)

IP Code Part 2 Design, Construction and Operation of Distribution Installations

IP Code Part 7 Petroleum Measurement Manual - Density, continuous density measurement

IP Code Part 9 Liquefied petroleum gas, Vol I large bulk pressure storage and refrigerated LPG

IP Code Part 13 Petroleum Measurement Manual - Fidelity and security of measurement data transmission systems, electric and/or

electronic pulsed data cabled transmission for fluid metering systems

IP Code Part 15 Area classification code for installations, handling flammable fluids

ISA 5.1 Instrument symbols and identification

ISA 5.2 Binary logic diagrams for process operation

ISA 5.3 Graphic symbols for distributed control shared display instrumentation, logic and computer systems

ISA 18.1 Annunciator sequences and specifications

ISA 55.1 Hardware testing of digital process computers (codes of BS-588 practice for testing computer based systems)

ISBN 92-67-10188-9 ISO guide to the expression of uncertainty in measurement 1995

ISGOTT International safety guide for oil tankers and terminals

ISO 15 Rolling bearings – radial bearings – boundary dimensions

ISO 31 Quantities and units

ISO 281 Rolling bearings – dynamic load ratings and rating life

ISO 636 Welding Consumables – Rods, Wires and Deposits for Tungsten Inert Gas Welding of Non-alloy and Fine-grain Steels – Classification

ISO 888 Bolts, screws and studs: nominal lengths and thread length for general bolts

ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts, screws and studs

ISO 1000 SI units and recommendations for the use of their multiples and of certain other units

ISO 1101 Technical drawings; Geometric tolerancing, tolerancing form, orientation, location and run out; Generalities, definitions, symbols, indications on drawings

ISO 1109 Refractory products -- Classification of dense shaped refractory products

ISO 1132 Rolling bearings – tolerances - definitions

ISO 1461 Metallic coatings: hot-dip galvanised coatings on fabricated ferrous products: requirements.

ISO 1461 Galvanised coatings on fabricated iron and steel articles

ISO 1680-Parts 1 & 2 Acoustics – Test code for the measurement of airborne noise emitted by rotating electrical machinery

ISO 1813 Belt-drives – V–ribbed belts, joined v-belts including wide section belts and hexagonal belts – Eletrica conductivity of antistatic endless V-belts – electrical conductivity – characteristics and methods of test

ISO 1927 Prepared unshaped refractory materials (dense and insulating) -- Classification

ISO 1940 Mechanical balancing of rotating bodies

Part 1 - Mechanical vibration – balance quality requirements of rigid rotors

ISO 1996 Part 1 Acoustics – Description, assessment and measurement of environmental noise

ISO 2063 Metallic and other coatings thermal spraying zinc aluminium and their alloys

ISO 2186 Fluid flow in closed conduits – Connections for pressure signal transmissions between primary and secondary elements.

ISO 2204 Acoustics – Guide to International standards on the measurement of air-borne acoustical noise and evaluating its effects on human beings

ISO 2245 Shaped insulating refractory products -- Classification

ISO 2314 Gas turbines - Acceptance tests

ISO 2372 Mechanical vibration of machines with operating speeds from 0-200 r/s – Basis for specifying evaluation standards

ISO 2409 Paints and varnishes - Cross cut test for adhesion

ISO 2548 Acceptance tests for centrifugal, mixed flow and axial pumps

ISO 2715 Liquid hydrocarbons; Volumetric measurements by turbine meter systems

ISO 2808 Paints and varnishes - Determination of film thickness

ISO 2954 Mechanical vibration of rotating and reciprocating machinery

ISO 3046 parts I to VI Reciprocating, internal combustion engines

ISO 3170 Petroleum liquids – Manual sampling

ISO 3171 Petroleum liquids – Automatic pipeline sampling

ISO 3183 Petroleum and natural gas industries -- Steel pipe for pipelines -- Technical delivery conditions

Part 1: Pipes of requirement class A

Part 3: Pipes of requirement class C

ISO 3511 Process measurement control functions and instrumentation - symbolic representation

ISO 3549 Zinc dust pigments for paint – Specifications and test methods

ISO 3582 Cellular plastics and cellular rubber, laboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame

ISO 3601 Part 1 Fluid systems Sealing devices – O rings

Part 1: Inside diameters, tolerances and size identification code

ISO 3690 Welding and allied processes – Determination of hydrogen content in ferritic steel arc weld metal

ISO 3743 Acoustics - Determination of sound power levels of noise sources - Engineering methods for special reverberation test rooms

ISO 3744 Acoustics – Determination of sound power levels of noise sources using sound pressure – Engineering method in an essentially free field over a reflecting surface

ISO 3746 Acoustics – determination of sound power levels of noise sources using sound pressure. Survey method using an enveloping measurement surface of a reflecting plan

ISO 4021 Hydraulic fluid power - Particulate contamination analysis - Extraction of fluid samples from lines of an operating system

ISO 4032 Hexagon nuts style 1: products grade A & B

ISO 4200 Plain end steel tubes, welded and seamless - General tables of dimensions and masses per unit length

ISO 4406 Hydraulic fluid power - Fluids - Method for coding level of contamination by solid particles

ISO 4624 Paints and varnishes-pull off test for adhesion

ISO 4628 Paints and varnishes - Evaluation of degradation of paint coatings -designation of intensity, quantity and size of common types of defects

ISO 5024 Petroleum liquids and gases -Measurement - Standard reference conditions

ISO 5167 Measurement of fluid by means of orifice plates, nozzles and venturi tubes inserted in circular cross-section conduits running full

ISO 5199 Industrial pumps – Technical specification for centrifugal and rotary pumps

ISO 5211 Part-turn valve actuator attachment

ISO 5752 Metal valves for use in flanged pipe systems – Face-to-face and centre-to-face dimensions

ISO 6141 Gas analysis - Calibration gas mixtures - Certificate of mixture preparation.

ISO 6142 Gas analysis - Preparation of calibration gas mixtures - Weighing methods

ISO 6143 Gas analysis - Determination of composition of calibration gas mixtures – Comparison methods

ISO 6326 Part 1 Natural gas – Determination of sulphur compounds – Part 1: General introduction

ISO 6327 Gas analysis - Determination of the water dew point of natural gas - Cooled surface condensation hygrometers

ISO 6385 Ergonomic principles in the design of work systems

ISO 6570 Parts 1, 2 & 3 Natural gas – Determination of potential hydrocarbon-liquid content Part 1: Principles and general requirements

Part 2: Weighing method

Part 3: Volumetric method

ISO 6974 Natural gas – Determination of hydrogen inert gases and hydrocarbons up to C8 - Gas chromatographic method

ISO 6975 Natural gas – Extended analysis – Gas chromatographic method

ISO 6976 Natural gas – Calculation of calorific values, density, relative density and Wobbe index from composition

ISO 6978 Natural gas – Determination of mercury

ISO 7235 Acoustics – Measurement procedures for ducted silencers – Insertion loss, flow noise and total pressure loss

ISO 7411 Hexagon headed bolts – product grade A & B

ISO 7415 Plain washers for high strength structural bolting, hardened and tempered

ISO 7730 Determination of the PMV and PPD indices and specifications of conditions for thermal comfort

ISO 7731 Ergonomics – Danger signals for public and work areas – Auditory danger signals

ISO 8297 Acoustics - Determination of sound power levels of multisource industrial plants for the evaluation of sound pressure levels in the environment

ISO 8501 Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness

ISO 8502 Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness

ISO 8503 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast cleaned steel substrates

ISO 8504 Preparation of steel substrates before application of paints and related products - Surface preparation methods

ISO 8995 Principles of visual ergonomics – the lighting of indoor work systems

ISO 9002 Quality systems – Model for Quality Assurance in Production, Installation, and Servicing

ISO 9606 Approval testing of welders. Fusion Welding

ISO 9613 Part 1 Acoustics – Attenuation of Sound During Propagation Outdoors” – Part 1 Calculation of the Absorption of Sound by the Atmosphere

ISO 9613 Part 2 Acoustics – Attenuation of Sound During Propagation Outdoors” - Part 2 General Method of Calculation

ISO 9614 Part 1 Acoustics – Determination of sound power levels of noise sources using sound intensity. Part 1 – Measurement at discrete points

ISO 9614 Part 2 Acoustics – Determination of sound power levels of noise sources using sound intensity. Part 2 – Measurement by scanning

ISO 9951 Measurement of gas flow in closed conduits – Turbine meters

ISO 10012 Quality assurance requirements for measuring equipment

ISO 10081 Classification of dense shaped refractory products

ISO 10101 Parts 1, 2 & 3 Natural gas–Determination of water by the Karl Fischer method

Part 1: Introduction

Part 2: Titration procedure

Part 3: Coulometric procedure

ISO 10303 Standard for the exchange of Product Data (STEP)

ISO 10441 Petroleum and natural gas Industries – Flexible couplings for mechanical power transmission – Special purpose applications

ISO 10474 Steel and steel products - Inspection documents

ISO 10494 Gas Turbines and Gas Turbine sets – Measurement of emitted airborne noise – Engineering/survey method

ISO 10715 Natural gas–Sampling guidelines

ISO 10723 Natural gas–Performance evaluation for on-line analytical systems

ISO 10816 Mechanical vibration – Evaluation of machine vibration by measurements on non-rotating parts

ISO 11014 Safety data sheet for chemical products - Content and order of selection

ISO 11064 -2 Ergonomic design of control centres – Part 2: Principles for the arrangement of control suites

ISO 11124 Preparation of steel substrates before application of paints and related products. Specifications for metallic blast-cleaning abrasives

ISO 11126 Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blastcleaning abrasives

ISO 11127 Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blastcleaning abrasives

ISO 11546 Part 2 Sound Insulation Performance of Enclosures – Measurement In-Situ

ISO 11691 Acoustics – Measurement of insertion loss of ducted silencers without flow – Laboratory survey method

ISO 12213 Parts 2 & 3 Natural gas – Calculation of compression factor –

Part 2: Calculation using molar–composition analysis

Part 3: Calculation using physical properties

ISO 12944 Paints and varnishes. Corrosion protection of steel structures by protective paint systems.

ISO 13443 Natural gas–Standard reference conditions

ISO 13686 Natural gas–Quality designation

ISO 13691 Petroleum and natural gas Industries – High speed special purpose gear units

ISO 13704(API 530) Calculation of heater tube thicknesses in petroleum refineries

ISO 13705 Fired Heaters - general refinery service

ISO 13706 Air-cooled heat exchangers for general refinery services

ISO 13709 Centrifugal pumps for petroleum, petrochemical and natural gas Industries

ISO 14001 Environmental management systems - specification with guidance for use

ISO 14313 Petroleum and natural gas industries – pipeline transportation systems – pipeline valves

ISO 14691 Petroleum and natural gas Industries – Flexible couplings for mechanical power transmission – General purpose applications

ISO 15156 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production, petroleum and natural gas Industries Part 1: General Principles for Selection of Cracking-Resistant Materials - Part 2:

Cracking-Resistant Carbon and Low Alloy Steels, and the use of Cast Irons - Part 3: Cracking-Resistant CRAs (corrosionresistant alloys) and other alloys

ISO 15175 Soil Quality – Characterization of Soil related to Ground Water Protection

ISO 15607 Specification and qualification of welding procedures for metallic materials – General rules

ISO 15613 Specification and Qualification of Welding Procedures for Metallic Materials – Qualification based on pre-production welding test

ISO 15614-1 Specification and Qualification of Welding Procedures for Metallic Materials – Welding Procedure Test –

Part 1: Arc and Gas Welding of Steels and Arc Welding of Nickel and Nickel Alloys

ISO 17846 Welding and Allied Processes – Health & Safety – Wordless precautionary labels for equipment and consumables used in Arc welding and cutting

ISO 19011 Guidelines for quality and/or environmental management systems auditing

ISO/DIS 9241 Ergonomic requirement for office work with visual display terminals (VDT's)

ISO/DIS 9857 Petroleum and liquid petroleum products - Continuous density measurement

ISO/DIS 11429 Safety of machinery – system of auditory and visual danger and information signals

ISO/DIS 11064 Ergonomic design of control centres

ISO/DIS 14532 Natural gas – Terminology

ISO EN 10168 Steel Products – Inspection Documents – List of Information and Description

ISO/IEC 3352 Acoustics – assessment of noise with respect to the intelligibility of speech

ISO/IEC 11801 Generic cabling system for customer premises

ISO TR 5168 Measurement of fluid flow – Evaluation of uncertainties

ISO/TR 7849 Estimation of airborne noise emitted by machinery using vibration measurement

ISO/TR 10465 Parts 1-3 Underground installation of flexible glass-reinforced thermosetting resins (GRP) Pipes

ISO/TR 12765 Measurement of fluid flow in closed conduits - Methods using transit-time ultrasonic flow meters

ISO/TR 15608 Welding – Guidelines for a metallic material grouping system

ISO/TR 17671-5 Welding – Recommendations for Welding of Metallic Materials – Part 5: Welding of Clad Steels

ISO/TR 17671-7 Welding – Recommendations for Welding of Metallic Materials – Part 7: Electron Beam Welding

ISO/TR 18569 Safety of Machinery – Guidelines for the understanding and use of safety of machinery standards

ISSMFE Report of the sub-committee on standardisation of penetration testing in Europe

ITU-T G.175 Transmission planning for private/public network interconnection of voice traffic

ITU-T G.611 Characteristic of symmetric cable pairs for analogue transmission

ITU-T G.621 Characteristic of 0.7/2.9 mm coaxil pairs

ITU-T G.651 Characteristic of 50/125 micrometre multimode graded index optical fibre cable

ITU-T G.652 Characteristic of a single mode optical fibre cable

ITU-T K.8 Separation in the soil between telecommunications cables and earthing system of power facilities

ITU-T K.11 Principles of protection against over voltages and over currents

ITU-T K.12 Characteristics of gas discharge tubes for the protection of telecommunications installations

ITU-T K.19 Joint use of trenches and tunnels for telecommunication and power cables

ITU-T K.20 Resistibility of telecommunications switching equipment to over voltages and over currents

ITU-T K.21 Resistibility of subscriber’s terminal to over voltages and over currents

ITU-T K.25 Protection of optical fibre cables

ITU-T K.34 Classification of electromagnetic environmental conditions for telecommunication equipment: basic EMC requirements

ITU-T K.51 Safety criteria for telecommunication equipment

ITU-T L.3 Armouring of cables

ITU-T L.10 Optical fibre cables for duct, tunnel, aerial and buried application

ITU-T L.12 Optical fibre joints

ITU-T L.13 Sheath joints and organisers of optical fibre cable in outside plant

ITU-T L.14 Measurement method to determine the tensile performance of optical fibre cables under load

ITU-T L.36 Single mode optical fibre connectors

ITU-T P.54 Sound level meters

ITU-T T.6 Facsimile coding schemes and coding control functions for Group 4 facsimile apparatus

MIL-A-18001K Anodes, sacrificial zinc alloy

MIL-HDBK-217 U.S. Military Handbook: Reliability prediction of electronic equipment

MSS SP 44 Steel pipe line flanges

MSS SP 58 Pipe hangers and supports - Materials, design and manufacture

MSS SP 69 Pipe hangers and supports - Selection and application

MSS SP 75 Specification for High Test Wrought Butt welding Fittings

MSS SP 97 Integrally reinforced forged carbon steel - Branch o/let fitting

NACE MR 0103 Materials Resistant to Sulfide Stress Cracking in Corrosive Petroleum Refining Environments

NACE MR 0175 Replaced by ISO 15156

NACE RP 0177 Mitigation of alternating current and lightning effects on metallic structures and corrosion control sytems

NACE RP 0178 Fabrication details, surface finish requirements and proper design considerations for tanks and vessels to be lined for

immersion service

NACE RP0186 Application of cathodic protection for external surfaces of steel well casings

NACE RP 0188 Discontinuity (holiday) testing of protective coatings

NACE RP0193 External cathodic protection of on-grade carbon steel storage tank bottoms

NACE RP0196 Galvanic anode cathodic protection of internal submerged surfaces of steel water storage tanks.

NACE RP0285 Corrosion control of underground storage tank systems by cathodic protection.

NACE RP0290 Impressed current cathodic protection of reinforcing steel in atmospherically exposed concrete structures

NACE RP0387 Metallurgical and inspection requirements for cast galvanic anodes for offshore applications

NACE RP0388 Impressed current cathodic protection of internal submerged surfaces of carbon steel water storage tanks.

NACE RP0492 Metallurgical and inspection requirements for offshore pipeline bracelet anodes

NACE RP0572 Design, installation, operation and maintenance of impressed current deep groundbeds

NACE RP0575 Internal cathodic protection systems in oil-treating vessels

NACE TM 01-77 Laboratory testing of metals for resistance to sulphide stress cracking in H2S environment

NAMUR NE 43 Recommendation for signal levels to extract failure information from digital transmitters with analogue output.

NAS 1638 Cleanliness requirements of parts used in hydraulic systems

NEMA 250 Enclosures for electrical equipment (1000 volts maximum)

NEMA SM23 Steam Turbines for Mechanical Drive Service

NEN 547-2 Safety of machinery – human body dimensions, principles for determining the dimensions required for access openings

NEN 1005-3 Manual handling

NEN 3410 Safety requirements for high voltage and low voltage installations in potentially explosive gas atmospheres

NEN-EN 457 Safety of machinery – auditory danger signals, general design requirements, design and testing

NEMA MG 1 Motors and Generators

NFPA 10 Portable fire extinguishers

NFPA 11 Low expansion foam systems

NFPA 11A Medium and High expansion foam systems

NFPA 11C Mobile foam apparatus

NFPA 12 Carbon dioxide extinguishing systems

NFPA 15 Water spray fixed systems for fire protection

NFPA 20 Installation of stationary pumps for fire protection

NFPA 58 Standard for the storage and handling of liquefied petroleum gases

NFPA 70 National electrical code

NFPA 72 National fire alarm code

NFPA 90A Installation of air conditioning and ventilation systems

NFPA 496 Standard for purged and pressurised enclosures for electrical equipment in hazardous (classified) locations

NFPA 750 Water mist protection systems

NFPA 2001 Clean agent extinguishing systems

NPR 2760 Mutual influence of pipelines and high voltage circuits

OCIMF Design and construction specification for marine loading arms

OCIMF Recommendations for oil tanker manifolds and associated equipment

PrEN 1005 Safety of machinery - Human physical performance

PrEN 12437 Safety of machinery - Permanent means of access to machines and industrial plants

RAL Colours from Deutsches Institut fur Gutesicherung und Kennzeichnung e.V.

S.34 Engineering recommendation S.34 A guide for assessing the rise of earth potential at substation sites

SFA 3009 Special protection

SMACNA HVAC systems - Testing, adjusting and balancing

SMACNA HVAC systems - Duct design

SMACNA HVAC air duct leakage test manual

SMACNA HVAC systems - Applications

SSPC SP1 Surface preparation specification No 1 – Solvent cleaning

SSPC PA 2 Paint application specification No 2 – Measurement of dry paint thickness with magnetic gauges.

TEMA Standards of the Tubular Exchanger Manufacturers Association

TNO Green Book Method for determination of possible damage to people and objects resulting from releases of hazardous materials (CPR 16E – 1992)

UBC 1997 Volume 2 1997 Uniform Building Code: Volume 2; Structural Engineering design provisions

UL 698 Safety standard for electrical industrial control equipment for use in hazardous (classified) locations, Class I, Groups A,B,C and D and Class II, Groups E, F and G

UL 698UL 698 UL standard for safety industrial control equipment for use in hazardous (classified) locations.

UL 886 Outlet boxes and fittings for use in hazardous (classified) locations

UL 913 UL standard for intrinsically safe apparatus and associated apparatus for use in Class I, II and III, division I, hazardous (classified) locations

UL - 1709 Rapid rise fire test of protection materials for structural steel

USEPA 40 CFR Part 60 40 Code of federal regulations-Protection of the environment Part 60- Standards of performance for new stationary sources

VDE 0510 Specification for electrical storage batteries and battery plants

VDI 2055 Thermal insulation for heated and refrigerated industrial and domestic installations

VDI 3733 Noise in pipes

VDI/VDE 3845 Industrial process control valves; interfaces between valves, actuators and auxiliary equipment

VGB R-450-Le Guideline for Boiler Feedwater, Boiler Water and Steam of Steam Generators with a Permissible Operating Pressure of >68 bar

WRC 107 Local stresses in spherical and cylindrical shells due to external loadings

WRC 297 Supplement to WRC bulletin 107

www.geocities.com/drmala66/A-MethodStatementWaterReservoir.pdf
www.geocities.com/drmala66/A-FacilitiesPhotos.doc

Dear Reader,

Thanks indeed for taking interest in reading the above work intended to provide projects practical information exchange to those who aspire to develop their professional skills to a level making themselves more useful in the professional fields fitting conveniently within the industry environment. by getting a fast opportunity for learning the professional aspects to some extent. The purpose of the above work is to bring to the young engineers projections of necessary operations and activities conducted by various professionals on industrial projects. I am basically a civil engineer by formal education experienced on reinforced concrete buildings & similar heavy structures in general. It is a fact that during experience in the profession one does not confine to one’s discipline only as multidiscipline projects are involved in profession & by virtue of interface exposures, professional is forced to grasp some knowledge of the other disciplines otherwise the problem solving shall be near impossible. This envisages every practicing engineer to accept the criteria that hesitation to interact with the relative disciplines should be discarded by being ready to adapt that with full involvement. This kind of approach & conduct shall provide multi facet of coordinated know how through discussions, meetings, report preparations, statement preparations, exposure to data sheets, reading design basis, FEED documents, contract conditions etc.
It is also suggested that should any of you have any descriptive experience on any of the projects, must share that experience by documentation on web or otherwise for transferring the learning to juniors. The world has been changing & developing extremely fast in science and technology forcing us to accept the facts as well as update or face obsolete status. University knowledge helps confined to the understanding engineering & technology principles without exposing to the world of real applications. The students should not expect also that type of knowledge to be imparted by the professional teachers of engineering universities who in fact unfortunately, have never been exposed to virtuality of the profession. I have seen many managers on the projects who had no engineering formal degrees but occupied senior managers positions in particular from the western nations but having considerable exposure & grasp as well as capability of application in fields successfully.
I have done some other works on writing as follows
Civil Engineering Buildings Practice published in 1996 by CBS publishers 11 Darya Ganj, New Delhi 110002, India
This book contains various aspects of building engineering from site management viewpoint, contract administration viewpoint, design philosophy & general engineering in the field as well as in design office
RCCBDS 2003

Buildings design application software based on Kani’s rotation contribution method giving calculations on excel format. The super macro formats are available on web @ following URL

Also I conceived a township project schematically in nineties that could not take off due to lack of provision of financing by the promoter.

In addition to aforesaid, many other useful files are available on the web for practical purposes.
I have also personal interest in using date of birth numbers interpretations using spiritual movements within the body that work also is available on web though it is not relevant to engineering. Only educated persons can understand the philosophy of this subject.
By this note I conclude.

Regards & Thanks once again for your valuable time as well as interest shown. Hope the work has been useful to you. Please write suggestions.

Eng Suraj Singh

Professional Engineer PE 28

Institution of Engineers India