The Front LEDs
       
Power
|
USB
|
LAN
|
ADSL
|
When flashing, it indicates that the device is turned on and working properly.
|
When this LED is lit, it indicates that the USB port is connected to the PC and working properly. When flashing data is received/send
|
When lit, it indicates that the LAN port is connected to the PC and working properly. When flashing data is received/send
|
When lit, it indicates the ADSL port is connected with the DSLAM and working properly. When flashing data is received/send.
|
      
LINE
(RJ-11 connector)
|
USB
(USB connector)
|
Reset
|
Ethernet Port
(RJ-45 connector)
|
Power
(jack)
|
On/Off
|
Connect the supplied RJ-11 cable to this port and the ADSL wallplug
|
Connect the supplied USB cable to this port when connecting to the PC.
|
Press to restore to the factory default settings.
|
Connect the supplied crossover cable to this port when connecting to a NIC (Network Interface card) in a PC.
Connect an UTP Ethernet cable to this port when connecting to a LAN such as an office or home network.
|
Connect the supplied power adapter to this jack.
|
Turn the modem/router on or off
| 1.5 Cabling
Through Ethernet Port
Connect the LAN cables: Use standard LAN cables to connect the PCs to the LAN ports (switch) on the homestation.
Make sure that all connected devices are turned on. Please, check that the PWR, LAN LNK and ADSL SYN LEDs are lit. If they are not, verify that you are using the proper cables.
If the cables are connected and the LEDs are lit normally, please go to section “3. Configuring the Network Properties” to modify the network settings.
Through USB Port
The product can be used as a Network Adapter on your PC. That means you do not have to install a network adapter first on your PC before connecting the DC-214/216 ADSL Homestation. Just connect the supplied USB cable to the USB port of the ADSL Homestation and connect the other end to the PC.
Make sure that all connected devices are turned on. Please, check that the PWR, and ADSL SYN LEDs are lit. If they are not, verify that you are using the proper cables.
If the cables are connected and the LEDs are lit normally, please go to section “2. Installing the USB Driver” below to setup this device.
Connect ADSL/power
Connect your ADSL cable to the LINE port on the homestation.
Connect the power adapter to the homestation. Only use the adapter that is delivered with your homestation. Connect the power cord to power inlet and turn the power switch on.
2. Installation 2.1 Installing the USB Driver
If you connect the ADSL Homestation to the USB port, for the first time the USB cable is connected to the PC, Windows will automatically detect the device. Follow the steps to install the USB driver.
Windows XP -
Select “Install from a list or specific location” and click “Next >”.
-
Insert the installation CD into the CD-ROM drive. Check “Include this location in the search” and click “browse”. Browse to the ‘driver’ folder on the CD-Rom. Click “Next >”.
-
Click “Continue Anyway” to pass the windows logo test.
-
Click “Continue Anyway” to pass the windows logo test.
-
Click “Finish”.
-
After a few moments, Windows will detect a new device, USB ADSL Adapter. Select “Install from a list or specific location”. Click “Next >”.
-
Check “Include this location in the search” and click “browse”. Browse to the ‘driver’ folder on the CD-Rom. Click “Next >”.
-
Click “Continue Anyway” to pass the windows logo test.
-
Click “Finish” to end installation.
-
After installing the driver, follow the section “3. Configuring the Network Properties” below to modify the network settings on your PC.
Windows 2000 -
Click “Next >”.
-
Insert the installation CD into the CD-ROM drive. Select “Search for a suitable driver for my device”. Click “Next>”.
-
Check “Specify a location”. Click “Next >”.
-
Click “browse”. Browse to the ‘driver’ folder on the CD-Rom. Click “Next >”.
-
Click “Next >” .
-
Click “Yes” to pass the digital signature.
-
Press “Finish”.
-
Click “Yes” to pass the digital signature.
-
After installing the driver, follow the section “3. Configuring the Network Properties” below to modify the network settings on your PC.
Windows Me -
Select “Specify the location of the driver”. Click “Next >”.
-
Insert the installation CD into the CD-ROM drive. Select “Specify a location”. and click “browse”. Browse to the ‘driver’ folder on the CD-Rom. Click “Next >”.
-
Click “Next >“.
-
Windows will start copying files to your system. Click “Finish”.
-
Select “Specify the location of the driver”. Click “Next >”.
-
Insert the installation CD into the CD-ROM drive. Select “Specify a location”. and click “browse”. Browse to the ‘driver’ folder on the CD-Rom. Click “Next >”.
-
Click “Next >“.
-
Windows will start copying files to your system. Click “Finish”.
-
Click “Yes” to restart your PC.
-
After installing the driver, follow the section “3. Configuring the Network Properties” below to modify the network settings on your PC.
Windows 98 -
Click “Next >”.
-
Select “Search for the best driver for your device [Recommended]”. Click “Next >”.
-
Insert the installation CD into the CD-ROM drive. Select “Specify a location”. and click “browse”. Browse to the ‘driver’ folder on the CD-Rom. Click “Next >”.
-
Click “Next >“.
-
Windows will start copying files to your system. Then, click “Finish”.
-
Click “Next >“.
-
Select “Search for the best driver for your device [Recommended]”. Click “Next >”.
-
Insert the installation CD into the CD-ROM drive. Select “Specify a location”. and click “browse”. Browse to the ‘driver’ folder on the CD-Rom. Click “Next >”.
-
Click “Next >“.
-
You will see the following screen prompting for the path of the Windows source files. Please specify a location of the original windows CD-Rom. Click “OK”.
-
Windows will start copying files to your system. Then, click “Finish”.
-
Click “Yes” to restart your PC.
-
After installing the driver, follow the section “3. Configuring the Network Properties” below to modify the network settings on your PC.
Share with your friends: |
