Providing Preconstructional Anti- termite treatment by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate of one percent concentration of CHLORPYRIFOC 20% EC ISI approved conforming (I.S.8944) to per square metre of surface area by high volume sprayer with ten years guarantee bond as per I.S.- 6313 (Part III) of 1971.
Spec.No.: As directed by Engineer- in-charge.
23
Providing PostconstructionalAnti- termite treatment to the soil along the external wall by punching holes of 1.2 to 1.5 cm diametre about 30 to 60 cm deep at 15 cm centre to centre as close to the wall as possible and inject one percent concentration of CHLORPYRIFOC 20% EC ISI approved conforming (I.S.8944)at the rate of 7.5 litre emulsion concrete per square metre and sealing the same with proper filling with two years guarantee bonds as per I.S.6313 (Part III) of 1971.
Spec.No.: As directed by Engineer- in-charge.
24
Providing and fixing a set of 5 fire buckets of special quality 0.3 m. diameter including painting, lettering and providing M.S.angle iron stand, iron hooks and locking arrangements and three coats of white enamel paint for stand etc. complete as per drawing.
Spec.No.: As directed by Engineer- in-charge.
25
Providing water proofing treatment of Old Terraces by removing existing treatment. Sealing of cracks by non shrink cracks fill compound by applying first coat of polymer modified semi-viscous paste prepared by mixing polymer of approved make (such as Master Seal 550/ brush bond / RoffSupercrete/ Webercrete/ Monobond / Perma shield / Hypercrate / Master Crete M 81) and Cement in 1:2 proportion ( 1 litre polymer : 2 Kg Cement)or Rohnex water proofing system in two coats(1kg powder,700 ml water and polymer jelly for first coat & 1 kg powder,500 ml water & polymer jelly for second coat) to a neatly cleaned and dust free concrete surface and upto 300 mm over parapet wall prepared by removing loose and deposited material with brush and water,laying glass fibre mesh of 10 x 10 specification of approved make over tacky surface of first coat of polymer followed by second coat in transverse direction,
Spec. No. As directed by Engineer-incharge and as per manufacturers specifications.
Sr. No.
Item of work
Sd.Sp.No. / Page No.
Additional Specification.
1
2
3
4
laying mechanical protective cover to polymer coating treatment with brick bat coba with burnt broken brick bats laid in C.M. 1:5 admixed with approved water proofingcompound, filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M. 1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm thick layers of same mortar added with polypropylene fibres at 125 gm per bag of cement including finishing the surface smooth with cement slurry admixed with approved water proofing compound, Marking finished surface by flase squares of 300 mm x 300 mm making thejunctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on court fee stamp paper of Rs. 100/- including ponding test etc. complete
26
Providing and fixing 60mm thick factory made Hydraulically pressed Mechanically vibrated and compacted precast inter locking cement concrete paving blocks in M-40 grade of approved size and shape as specified 50 mm in gray cement and top surface 10 mm in white cement with coloured pigment including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying paving blocks in position over prepared bed of sand of 50 mm thickness including necessary excavation in all stratas, spreading blindge of fine sand over the prepared bed, compacting blocks by plate vibrator etc. complete.
Spec.No.: As directed by Engineer- in-charge.
27
Providing and laying hand cutpolished kota stone Flooring 20 mm to 25 mm thick diamond pattern on a bed of C.M. 1:6 including cement float, filling joints with neat cement slurry, curing rubbing, polishing and cleaning complete
Spec.No.: Bd.M.3/Page No.380
28
Providing and fixing in required position skirting or dado of polished Kota stone slabs 20 mm to 25 mm thick and required width after making the wall portion to required level with C.M.1:4 and fixing tiles with ready made adhesive including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete.
Spec.No.: Bd.M.5/Page No.381
Sr. No.
Item of work
Sd.Sp.No. / Page No.
Additional Specification.
1
2
3
4
29
Providing and Laying vetrified tiles of approved make and quality of required size and thickness for flooring in required position laid on bed of C.M.1:4 including cement float, filling joint with white / colour cement slurry, cleaning, curing, complete. a) 600 mm x 600 mm. Size RAK make or eqivalent.
Samples to be got approved from Executive Engineer.
30
Providing and fixing vetrified tiles of approved make and quality of required size for dado and skirting in required position with ready made adhesive mortar of approved quality in required position after making the wall portion in level in plaster of C.M. 1:4 including joint filling with white/colour cement slurry cleaning curing complete. a) 600 mm x 600 mm. sizeSize RAK make or eqivalent.
Samples to be got approved from Executive Engineer..
31
Providing and Laying ceramic tiles of approved quality , required size and 5.5.mm thickness for flooring in required position laid on bed of C.M.1:4 including cement float, filling joint with white / colour cement slurry, cleaning, curing, complete.
Samples to be got approved from Executive Engineer.
32
Providing and fixing ceramic tiles of approved quality , required size and 5.5.mm thickness for dado and skirting in required position with ready made adhesive mortar of approved quality in required position after making the wall portion in level in plaster of C.M. 1:4 including joint filling with white/colour cement slurry cleaning curing complete.
Providing and applying Luster finish proof paint of approved colour and shade to existing surface in two coats including scaffolding, preparing the surface to receive paint and applying putty etc. complete.
Samples to be got approved from Executive Engineer.
34
Providing and fixing cold rolled steel frame for door 100 mm x 60 mm of 16 guage as per drawing with/without ventilator including holdfasts, hinges welded to the frame, including filling cement mortar 1:6 in hollow core and finishing with oil painting etc. complete.
Samples to be got approved from Executive Engineer.
35
Providing and fixing double leaf door,with country teak wood shutter and panels as per detailed drawing including iron oxidised fixtures and fastening stoppers and finishing with one coat of primer complete. (Excluding door frame) Panels of 12 mm thick, exterior grade prelaminated particle board laminated on both side.
Samples to be got approved from Executive Engineer.
Sr. No.
Item of work
Sd.Sp.No. / Page No.
Additional Specification.
1
2
3
4
36
Providing and fixing single leaf door,with country teak wood shutter and panels as per detailed drawing including iron oxidised fixtures and fastening stoppers and finishing with one coat of primer complete. (Excluding door frame) Panels of 12 mm thick, exterior grade prelaminated particle board laminated on both side.
Spec.No.: Bd.T.30/Page No.496
37
Providing & fixing of approved make PVC door frames made out of rigid PVC hollow section of size 60mm x 50mm Machine cut with solid polymetric reinforcement for holding hinges and tie rod at bottom including fixing 100mm long full threaded metal screw in PVC roll plugs inserted in wall as hold fast and remaking damaged surface etc. complete.
Spec.No.: As directed by Engineer- in-charge.
38
Providing and fixing single leaf door shutterof approved make and colour made out of extruded rigid PVC hollow section DWUF-306 shutter frame of size 33 mm x 47 mm having double wall construction as vertical styles, top and bottom rails and middle locks rail of size 33 mm x 94 mm and the panel in fill SPUF-101 multichamber hollow plastic section of size 20 mm x 200 mm joined each other by tongue and groove interlocking system duly inserted in shutter frame and all shutter frames, lock rails, styles reinforced by seasoned wood inserted inside for fixing of hinges, aldrops, tower bolts and door stoppers etc. all corners should be Machine cut, joined each other by metal screw after inserting rigid "L" bracket PVC reinforcement of size 125 mm x 200 mm. Including synthetic metal fixtures and fastenings, remaking damaged surface etc. complete.
Spec.No.: As directed by Engineer- in-charge.
39
a) Providing and fixing in position alluminium louvered windows/ ventilators of various sizes with powder coating as per detailed drawings and specifications including aluminium frames 80 x 38 mm box type 5 mm thick sheet glass louveres, clips / rubber plain P.V.C. gaskets of approved quality etc.complete. b) For powder coated aluminium window / ventilator (Sample to be got approved from Ex. Engineer before use) ( Jindal Make or equivalent )
Spec.No.: As directed by Engineer- in-charge. Samples to be got approved from Executive Engineer
Sr. No.
Item of work
Sd.Sp.No. / Page No.
Additional Specification.
1
2
3
4
40
Supplying and fixing in position aluminium extruded section Three track sliding windows upto 1.2 metre height, outer frame made from section of over all size 80 mm x 45 mm, bottom section with or without drain section track weighing 0.90 kg per metre and top and side section weighing 0.838 kg per running metre with shutter or sections made of 19 mm x 40 mm size having average weight of 0.6 kg per running metre(or as required size) with change in proportionate weight,with 5.5. mm selected quality plain sheet glass fixed with new neoprene gasket shutters to be provided with nylon encased stainless rollers, necessary locks and handles complete. (As per Architect's drawing no.Job No. T- MISC/5000 Drg.No.22 dated 3.2.1992) ( Jindal Make or equivalent )
Spec.No.: As directed by Engineer- in-charge. Samples to be got approved from Executive Engineer
41
Providing and fixing mild steel grill work for windows, ventilators, etc. 20 kg/sqm as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.
Spec.No.: Bd.U.1/Page No.537
42
Providing and fixing suspended ceiling system consisting of fine fissured RH-90 ( Arm Strong ) tiles with Tagular tile edges in sizes 600 x 600 x 16 mm for grids ofnormal size laid on silhouette 15 XL hot dipped galvanized grid system with 15 mm wide T - section flages, 1200 mm long to be interlocked between main runner at 600 mm centers to from 1200 x 600 mm main runners of size 15 x 44 x 8 mm 3600 mm long and T-section with double stitching cross runners 15x44x8 mm Molders, cut cross tee longer than 600 mm to be supported independently 600 x 600 Modules to be framed by filling cross centrally between the 1200 mm cross tee and perimeter wall angle 19x22x3000 mm long & to hold the grid sufficient Nos of suspenders to be fixed etc. complete. Including of G.I. section for the gypsum false ceiling of 12.50 mm thickness.
Spec.No.: As directed by Engineer- in-charge. Samples to be got approved from Executive Engineer Only approved materials & samples shall be used.
Sr. No.
Item of work
Sd.Sp.No. / Page No.
Additional Specification.
1
2
3
4
43
43
Providing, supplying and fixing in position anodised extruded aluminium partitions, partly glazed and partly laminated having frame made out of extruded tubular section of size 40mm x 65 mm with 12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to I.S.12823-1990, laminated on both sides, Novateak or equivalent and 5 mm thick selected quality float glass pannels fixed with aluminium glass clips 12 mm x 12 mm and rubber cushioning beading to glass partition as per approved drawing etc. complete. b) For powder coating extruded aluminium partitions (Sample to be got approved from Ex. Engineer before use) Jindal Make or equivalent . Providing, supplying and fixing in position anodised extruded alluminium partitions, with both sides laminated paneles having frame made out of alluminium extruded tubular section of size 40mm x 65 mm with 12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to I.S.12823-1990, laminated on both sides, Novateak or equivalent fixed with aluminium glazing clips 12 mm x 12 mm as per approved drawing etc. complete. (Sample to be got approved from Ex. Engineer before use) Jindal Make or equivalent
Spec.No.: As directed by Engineer- in-charge.
Spec.No.: As directed by Engineer- in-charge
44
Providing and fixing anodised aluminium fully glazed doors including door frame with powder coating 5 mm thick sheet glass necessary fixtures and fastenings, neoprene type rubber plain gaskets as per detailed drawing and specifications etc. complete. Jindal Make or equivalent Sample to be got approved from Ex. Engineer before use)
Spec.No.: As directed by Engineer- in-charge.
45
Providing and fixing alluminium grill decorative of various sizes as per detail drawing and specification etc. complete
Spec.No.: As directed by Engineer- in-charge.
46
Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted / welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete.
Spec. No. : Bd.C. 2/Page No. 275
47
Providing and fixing 1st class white glazed earthenware "Orissa type" W.C.Pan 600 x 400 mm size including 'P'or 'S'trap UPVC soil and vent pipe upto the outside face of the wall, 1:5:10 cement concrete bedding, 10 litre fibre high level flushing cistern with fittings, inlet pipe with stop tap, bracket for fixing the cistern, 32 mm dia. UPVC flush pipe with fitting and clamps, 20 mm dia. UPVC over flow pipe with mosquito proof coupling, chain and pulley, painting of the exposed pipe and cutting and making good walls and floor, testing etc. complete.(Prior approval of sample and brand by Ex.Engineer is necessary before use.)
