Quick Installation Manual Enterprise High Gain Wireless Router

Thank you for purchasing Enterprise High Gain wireless Router. This manual will instruct you how to configure router, and enable you to use it in a perfect status. After you have installed the router, you will be able to enjoy the surfing feely.

 

1.1. Wireless Router Connection

Below diagram is the connection instruction

Reset: Press it for 5-10 seconds, then, the router return to its default configuration.

Wan: Wan connectin

LAN1-LAN4: LAN Connection to connect PC by cable.

Power: for Power supply

If use router by cable, the correct connecting way is as below:

1. Connect PC to one of the lan ports

2. Connect router’s Wan Port to ADSL Modem. Please do this only after you have finished the router configuration, to avoid any installation issues. This is very important. Please do it accordingly

3. If you already connect router to ADSL Modem, then, please firstly disconnected it, then, reset wireless router.

1. 
   Switch on PC, click on right ‘My Network Place’, then click on right the “local area connection”->“properties”-> “Internet protocol（TCP/IP）” and “Properties”.
   

B, Click “General ” ,Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click OK.

B. Start PC’s Internet Explorer, and enter http：//192.168.0.1, press enter.

C. Users will see the following login page, Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.

D. Then, enter the configuration page of the router as below:

『Remark』Set up the router is necessary by wired or wireless network type. Please note the router setup page is not for internet.

Click and enter into“setting wizard” for below 3 steps.

Please choose any one broadband setting method of below 3

User Name:gzDSL38912111@163.gd

Password××××××××

Please fill in user name and password provided by telecom operator as picture.

lease keep default settings and click “next” if no any special setting request

As example of a telecom operator fixed IP address with below related details.

Subnet mask：255.255.255.0

Gateway：212.197.17.254

Main domain name server：202.96.128.68

Sub domain name server：202.96.134.133

A. Static IP user should fill in the blank column upon IP address provided by telecom operator,as below picture.

B. Click “Next” for next settings after finish.

No need make settings for dynamic IP user and click “nexts”

Here you can set up LAN IP and DHCP address upon your needs.Or click “next” for wireless settings.

Pls write down the right SSID and security method in above picture( It is better to choose WPAPSK with secutiry), click finish to share the network.

Remarks: if you computer with build in 802.11b/g/n wireless USB adapter, and can’t search the available network, pls contact with after-sale department of your computer seller.

List of Accessory:

1, Wireless broadband router;

2, power adapter;

3, quick installation guide;

4, 1Meter LAN Cable;

5, warranty card.

FAQ:

1、It can not enter router setting interface after typing router IP in browser..

Please check if the router is working normally. The SYS will flashing after few seconds while energized. Otherwise it has internal fault, please send us to handle.

Please check whether the networking cable connects router well,also its corresponding cable interface light is light? If only sometimes lighting doesn’t mean the networking cable is connected..

Please run the ping in the command prompt to verify the network connection between your PC(s) and the router. LAN Interface with IP address 192.168.2.1

If yes, then check your browser, whether it sets up surfing via a proxy server, if without, please don't do that.

If no, you can hold “RESET” with 7 seconds to restore factory settings and try to ping 192.168.2.1 to see if it can be verified

If failed again, please call our technical support hot line.

Please restore factory settings. The way is to hold” RESET” button with 15 seconds.

Pls check is there any other DHCP server in LAN, if yes, pls close it.

The router’s original IP address is 192.168.1.1, pls make sure this IP address is different from other local networking. If same, pls change one. If the IP address is same in two different computers , pls change one to make them different.
How to access the internet for the dynamic IP users?

Enter into the router’s management interface, and set it as Dynamic IP in internet settings, then save.

Some ISPs binding the MAC address to computer’s LAN Card, you should copy the router’s MAC address on this condition.

The way of copy MAC address is as below: