Wi-Fi Enable 89



Download 300.8 Kb.
Page1/6
Date20.06.2017
Size300.8 Kb.
#21229
  1   2   3   4   5   6
Logs

Contents


Boot-up 1

Serial 1


ADB 18

Wi-Fi Enable 89

Serial 89

ADB 92


Bluetooth Enable 93

ADB 93



Boot-up

Serial


CCCCCCCC

U-Boot SPL 2013.01.01-00129-g6d40c2a (Sep 20 2013 - 13:51:04)

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Peripheral mode controller at 47401000 using PIO, IRQ 0

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Host mode controller at 47401800 using PIO, IRQ 0

OMAP SD/MMC: 0

reading u-boot.img

reading u-boot.img

U-Boot 2013.01.01-00129-g6d40c2a (Sep 20 2013 - 13:51:04)

I2C: ready

DRAM: 512 MiB

WARNING: Caches not enabled

NAND: 256 MiB

MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1

*** Warning - bad CRC, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Peripheral mode controller at 47401000 using PIO, IRQ 0

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Host mode controller at 47401800 using PIO, IRQ 0

Net: not set. Validating first E-fuse MAC

cpsw


Hit any key to stop autoboot: 0

mmc0 is current device

SD/MMC found on device 0

reading uEnv.txt

214 bytes read in 4 ms (51.8 KiB/s)

Loaded environment from uEnv.txt

Importing environment from mmc ...

Running uenvcmd ...

reading uImage

4087336 bytes read in 456 ms (8.5 MiB/s)

## Booting kernel from Legacy Image at 81000000 ...

Image Name: Linux-3.2.0-00244-gcf99001-dirty

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 4087272 Bytes = 3.9 MiB

Load Address: 80008000

Entry Point: 80008000

Verifying Checksum ... OK

Loading Kernel Image ... OK

OK

Starting kernel ...



Uncompressing Linux... done, booting the kernel.

[ 0.000000] Linux version 3.2.0-00244-gcf99001-dirty (android@ccrxpb-eng00) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #2 Tue Sep 24 13:54:58 MDT 2013

[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine: am335xevm

[ 0.000000] Memory policy: ECC disabled, Data cache writeback

[ 0.000000] AM335X ES1.0 (sgx neon )

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024

[ 0.000000] Kernel command line: console=ttyO0,115200n8 androidboot.console=ttyO0 mem=256M root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait init=/init ip=off

[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

[ 0.000000] Memory: 256MB = 256MB total

[ 0.000000] Memory: 250172k/250172k available, 11972k reserved, 0K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)

[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)

[ 0.000000] .text : 0xc0008000 - 0xc075e000 (7512 kB)

[ 0.000000] .init : 0xc075e000 - 0xc07b2000 ( 336 kB)

[ 0.000000] .data : 0xc07b2000 - 0xc081d1b0 ( 429 kB)

[ 0.000000] .bss : 0xc081d1d4 - 0xc0974ec0 (1376 kB)

[ 0.000000] NR_IRQS:396

[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts

[ 0.000000] Total of 128 interrupts on 1 active controller

[ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz

[ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz

[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms

[ 0.000000] Console: colour dummy device 80x30

[ 0.000152] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144)

[ 0.118988] pid_max: default: 32768 minimum: 301

[ 0.119110] Security Framework initialized

[ 0.119201] Mount-cache hash table entries: 512

[ 0.119628] CPU: Testing write buffer coherency: ok

[ 0.119689] ftrace: allocating 21566 entries in 64 pages

[ 0.187438] omap_hwmod: pruss: failed to hardreset

[ 0.188293] print_constraints: dummy:

[ 0.188537] NET: Registered protocol family 16

[ 0.189758] OMAP GPIO hardware version 0.1

[ 0.190856] omap_mux_init: Add partition: #1: core, flags: 0

[ 0.191955] omap_i2c.1: alias fck already exists

[ 0.192504] omap2_mcspi.1: alias fck already exists

[ 0.192626] omap2_mcspi.2: alias fck already exists

[ 0.192779] edma.0: alias fck already exists

[ 0.192779] edma.0: alias fck already exists

[ 0.192810] edma.0: alias fck already exists

[ 0.202636] bio: create slab at 0

[ 0.203643] SCSI subsystem initialized

[ 0.204498] usbcore: registered new interface driver usbfs

[ 0.204620] usbcore: registered new interface driver hub

[ 0.204772] usbcore: registered new device driver usb

[ 0.205078] registerd cppi-dma Intr @ IRQ 17

[ 0.205078] Cppi41 Init Done Qmgr-base(d087a000) dma-base(d0878000)

[ 0.205108] Cppi41 Init Done

[ 0.205108] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3

[ 0.205291] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1

[ 0.218994] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz

[ 0.220306] tps65910 1-002d: JTAGREVNUM 0x0

[ 0.222503] print_constraints: VRTC:

[ 0.223846] print_constraints: VIO: at 1800 mV

[ 0.226074] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal

[ 0.228271] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal

[ 0.229187] print_constraints: VDD3: 5000 mV

[ 0.230499] print_constraints: VDIG1: at 1800 mV

[ 0.231842] print_constraints: VDIG2: at 1800 mV

[ 0.233154] print_constraints: VPLL: at 1800 mV

[ 0.234497] print_constraints: VDAC: at 1800 mV

[ 0.235839] print_constraints: VAUX1: at 1800 mV

[ 0.237182] print_constraints: VAUX2: at 3300 mV

[ 0.238494] print_constraints: VAUX33: at 3300 mV

[ 0.239837] print_constraints: VMMC: at 3300 mV

[ 0.240142] tps65910 1-002d: No interrupt support, no core IRQ

[ 0.240722] Advanced Linux Sound Architecture Driver Version 1.0.24.

[ 0.241516] Switching to clocksource gp timer

[ 0.260314] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)

[ 0.260559] musb-hdrc musb-hdrc.0: dma type: dma-cppi41

[ 0.260742] MUSB0 controller's USBSS revision = 4ea20800

[ 0.261718] musb-hdrc musb-hdrc.0: USB OTG mode controller at d083c000 using DMA, IRQ 18

[ 0.261962] musb-hdrc musb-hdrc.1: dma type: dma-cppi41

[ 0.262145] MUSB1 controller's USBSS revision = 4ea20800

[ 0.262634] musb-hdrc musb-hdrc.1: MUSB HDRC host driver

[ 0.262725] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1

[ 0.262847] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[ 0.262878] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 0.262878] usb usb1: Product: MUSB HDRC host driver

[ 0.262908] usb usb1: Manufacturer: Linux 3.2.0-00244-gcf99001-dirty musb-hcd

[ 0.262908] usb usb1: SerialNumber: musb-hdrc.1

[ 0.263427] hub 1-0:1.0: USB hub found

[ 0.263458] hub 1-0:1.0: 1 port detected

[ 0.263885] musb-hdrc musb-hdrc.1: USB Host mode controller at d083e800 using DMA, IRQ 19

[ 0.264282] NET: Registered protocol family 2

[ 0.264495] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.264862] TCP established hash table entries: 8192 (order: 4, 65536 bytes)

[ 0.265014] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.265136] TCP: Hash tables configured (established 8192 bind 8192)

[ 0.265136] TCP reno registered

[ 0.265136] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.265167] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.265380] NET: Registered protocol family 1

[ 0.265686] RPC: Registered named UNIX socket transport module.

[ 0.265686] RPC: Registered udp transport module.

[ 0.265686] RPC: Registered tcp transport module.

[ 0.265716] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.265960] NetWinder Floating Point Emulator V0.97 (double precision)

[ 0.381866] ashmem: initialized

[ 0.382141] VFS: Disk quotas dquot_6.5.2

[ 0.382202] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[ 0.383087] fuse init (API version 7.17)

[ 0.383331] msgmni has been set to 488

[ 0.384399] io scheduler noop registered

[ 0.384429] io scheduler deadline registered

[ 0.384490] io scheduler cfq registered (default)

[ 0.387176] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0

[ 1.035125] console [ttyO0] enabled

[ 1.039215] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1

[ 1.046905] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2

[ 1.054595] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3

[ 1.062255] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4

[ 1.069915] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5

[ 1.077728] [drm] Initialized drm 1.1.0 20060810

[ 1.088623] brd: module loaded

[ 1.095001] loop: module loaded

[ 1.098480] i2c-core: driver [tsl2550] using legacy suspend method

[ 1.104980] i2c-core: driver [tsl2550] using legacy resume method

[ 1.111389] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write

[ 1.125305] Detected a daughter card on AM335x EVM..

[ 1.130310] CPLD version: CPLD1.0F

[ 1.134185] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write

[ 1.149353] Board name: A33515BB

[ 1.152740] Board version: 1.4A

[ 1.156005] SKU: SKU#01

[ 1.159088] The board is general purpose EVM in profile 0

[ 1.165557] da8xx_lcdc.0: alias fck already exists

[ 1.170867] da8xx_lcdc da8xx_lcdc.0: GLCD: Found TFC_S9700RTWV35TR_01B panel

[ 1.190979] omap-gpmc omap-gpmc: GPMC revision 6.0

[ 1.196044] Registering NAND on CS0

[ 1.200103] omap_i2c.2: alias fck already exists

[ 1.222167] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz

[ 1.228302] tsl2550 2-0039: standard operating mode

[ 1.234283] tsl2550 2-0039: registering lightsensor-level input device

[ 1.241333] input: lightsensor-level as /devices/virtual/input/input0

[ 1.248107] tsl2550 2-0039: support ver. 1.2 enabled

[ 1.253723] davinci-mcasp.1: alias fck already exists

[ 1.259338] davinci-mcasp.0: alias fck already exists

[ 1.265045] omap_hsmmc.0: alias fck already exists

[ 1.270294] omap_hsmmc.2: alias fck already exists

[ 1.275573] am335xevm: bt init

[ 1.281951] (stk) :sysfs entries created

[ 1.286163] (stk) : debugfs entries created

[ 1.290496] (hci_tty): inside hci_tty_init

[ 1.295135] (hci_tty): allocated 251, 0

[ 1.299194] _regulator_get: 2-0018 supply Vdd not found, using dummy regulator

[ 1.306793] _regulator_get: 2-0018 supply Vdd_IO not found, using dummy regulator

[ 1.335388] lis3lv02d: 8 bits 3DLH sensor found

[ 1.432373] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input1

[ 1.442291] NFC Driver for TI WiLink

[ 1.446044] (nfcdrv) nfc_drv_probe: allocated major 250, minor 0

[ 1.453216] mtdoops: mtd device (mtddev=name/number) must be supplied

[ 1.460388] omap2-nand driver initializing

[ 1.465026] ONFI flash detected

[ 1.468444] ONFI param page 0 valid

[ 1.472076] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)

[ 1.480926] Creating 8 MTD partitions on "omap2-nand.0":

[ 1.486511] 0x000000000000-0x000000020000 : "SPL"

[ 1.492462] 0x000000020000-0x000000040000 : "SPL.backup1"

[ 1.498992] 0x000000040000-0x000000060000 : "SPL.backup2"

[ 1.505523] 0x000000060000-0x000000080000 : "SPL.backup3"

[ 1.512023] 0x000000080000-0x000000260000 : "U-Boot"

[ 1.518890] 0x000000260000-0x000000280000 : "U-Boot Env"

[ 1.525390] 0x000000280000-0x000000780000 : "Kernel"

[ 1.533508] 0x000000780000-0x000010000000 : "File System"

[ 1.643188] OneNAND driver initializing

[ 1.647827] CAN device driver interface

[ 1.651855] CAN bus driver for Bosch D_CAN controller 1.0

[ 1.702178] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6

[ 1.708618] davinci_mdio davinci_mdio.0: detected phy mask fffffffe

[ 1.716186] davinci_mdio.0: probed

[ 1.719726] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown

[ 1.727172] PPP generic driver version 2.4.2

[ 1.731781] PPP BSD Compression module registered

[ 1.736724] PPP Deflate Compression module registered

[ 1.742156] usbcore: registered new interface driver cdc_ether

[ 1.748291] usbcore: registered new interface driver cdc_eem

[ 1.754241] usbcore: registered new interface driver dm9601

[ 1.760131] usbcore: registered new interface driver cdc_subset

[ 1.766357] cdc_ncm: 04-Aug-2011

[ 1.769775] usbcore: registered new interface driver cdc_ncm

[ 1.775787] usbcore: registered new interface driver cdc_acm

[ 1.781677] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters

[ 1.790039] Initializing USB Mass Storage driver...

[ 1.795257] usbcore: registered new interface driver usb-storage

[ 1.801513] USB Mass Storage support registered.

[ 1.806518] usbcore: registered new interface driver usbserial

[ 1.812683] USB Serial support registered for generic

[ 1.817993] usbcore: registered new interface driver usbserial_generic

[ 1.824829] usbserial: USB Serial Driver core

[ 1.829406] USB Serial support registered for GSM modem (1-port)

[ 1.835845] usbcore: registered new interface driver option

[ 1.841674] option: v0.7.2:USB Driver for GSM modems

[ 1.848602] gadget: Mass Storage Function, version: 2009/09/11

[ 1.854827] gadget: Number of LUNs=1

[ 1.858642] lun0: LUN: removable file: (no medium)

[ 1.864013] gadget: android_usb ready

[ 1.867950] musb-hdrc musb-hdrc.0: MUSB HDRC host driver

[ 1.873565] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2

[ 1.881408] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002

[ 1.888519] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 1.896057] usb usb2: Product: MUSB HDRC host driver

[ 1.901245] usb usb2: Manufacturer: Linux 3.2.0-00244-gcf99001-dirty musb-hcd

[ 1.908691] usb usb2: SerialNumber: musb-hdrc.0

[ 1.913970] hub 2-0:1.0: USB hub found

[ 1.917907] hub 2-0:1.0: 1 port detected

[ 1.922729] mousedev: PS/2 mouse device common for all mice

[ 1.929412] input: matrix-keypad as /devices/platform/matrix-keypad/input/input2

[ 1.938140] input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input3

[ 1.946777] using rtc device, am33xx-rtc, for alarms

[ 1.951812] omap_rtc am33xx-rtc: rtc core: registered am33xx-rtc as rtc0

[ 1.959106] i2c /dev entries driver

[ 1.963104] Linux video capture interface: v2.00

[ 1.968231] usbcore: registered new interface driver uvcvideo

[ 1.974243] USB Video Class driver (1.1.1)

[ 1.979431] input: lm75-temp as /devices/virtual/input/input4

[ 1.985839] lm75 2-0048: hwmon0: sensor 'tmp275'

[ 1.993347] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec

[ 1.999877] device-mapper: uevent: version 1.0.3

[ 2.004943] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com

[ 2.015563] cpuidle: using governor ladder

[ 2.019989] cpuidle: using governor menu

[ 2.027862] usbcore: registered new interface driver usbhid

[ 2.033752] usbhid: USB HID core driver

[ 2.038208] logger: created 256K log 'log_main'

[ 2.043060] logger: created 256K log 'log_events'

[ 2.048065] logger: created 256K log 'log_radio'

[ 2.053009] logger: created 256K log 'log_system'

[ 2.058471] tiadc tiadc: attached adc driver

[ 2.063385] usbcore: registered new interface driver snd-usb-audio

[ 2.071197] _regulator_get: 2-001b supply IOVDD not found, using dummy regulator

[ 2.079040] _regulator_get: 2-001b supply DVDD not found, using dummy regulator

[ 2.086730] _regulator_get: 2-001b supply AVDD not found, using dummy regulator

[ 2.094421] _regulator_get: 2-001b supply DRVDD not found, using dummy regulator

[ 2.105682] asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok

[ 2.112976] asoc: wl1271bt <-> davinci-mcasp.0 mapping ok

[ 2.119628] ALSA device list:

[ 2.122772] #0: AM335X EVM

[ 2.125762] oprofile: hardware counters not available

[ 2.131042] oprofile: using timer interrupt.

[ 2.135681] Netfilter messages via NETLINK v0.30.

[ 2.140716] nf_conntrack version 0.5.0 (3908 buckets, 15632 max)

[ 2.147338] ctnetlink v0.93: registering with nfnetlink.

[ 2.152984] NF_TPROXY: Transparent proxy support initialized, version 4.1.0

[ 2.160247] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.

[ 2.166687] xt_time: kernel timezone is -0000

[ 2.171478] ip_tables: (C) 2000-2006 Netfilter Core Team

[ 2.177276] arp_tables: (C) 2002 David S. Miller

[ 2.182189] TCP cubic registered

[ 2.185729] NET: Registered protocol family 10

[ 2.191192] Mobile IPv6

[ 2.193847] ip6_tables: (C) 2000-2006 Netfilter Core Team

[ 2.199676] IPv6 over IPv4 tunneling driver

[ 2.204742] NET: Registered protocol family 17

[ 2.209411] NET: Registered protocol family 15

[ 2.214080] can: controller area network core (rev 20090105 abi 8)

[ 2.220642] NET: Registered protocol family 29

[ 2.225311] can: raw protocol (rev 20090105)

[ 2.229766] can: broadcast manager protocol (rev 20090105 t)

[ 2.235717] Registering the dns_resolver key type

[ 2.240692] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3

[ 2.248718] ThumbEE CPU extension supported.

[ 2.253265] mux: Failed to setup hwmod io irq -22

[ 2.258941] Power Management for AM33XX family

[ 2.263854] Trying to load am335x-pm-firmware.bin (60 secs timeout)

[ 2.270507] Copied the M3 firmware to UMEM

[ 2.274902] Cortex M3 Firmware Version = 0x181

[ 2.284454] clock: disabling unused clocks to save power

[ 2.291625] Detected MACID=0:18:31:8f:2e:ac

[ 2.298278] input: gpio-keys as /devices/platform/gpio-keys/input/input5

[ 2.305694] omap_rtc am33xx-rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801)

[ 2.315216] Waiting for root device /dev/mmcblk0p2...

[ 2.355102] mmc0: new high speed SDHC card at address 1234

[ 2.361328] mmcblk0: mmc0:1234 SA08G 7.28 GiB

[ 2.368133] mmcblk0: p1 p2 p3 p4

[ 2.486816] mmc1: card claims to support voltages below the defined range. These will be ignored.

[ 2.506988] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)

[ 2.513702] mmc1: new high speed SDIO card at address 0001

[ 5.087921] EXT4-fs (mmcblk0p2): recovery complete

[ 5.096343] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)

[ 5.104858] VFS: Mounted root (ext4 filesystem) on device 179:2.

[ 5.111663] Freeing init memory: 336K

[ 5.147033] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.

[ 5.261230] init: cannot open '/initlogo.rle'

[ 7.041381] EXT4-fs (mmcblk0p3): recovery complete

[ 7.050018] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic

[ 7.098205] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'

[ 7.216796] Disabling lock debugging due to kernel taint

[ 7.223144] Compat-wireless backport release: ol_r8.a5.01

[ 7.228820] Backport based on wl18xx.git ol_r8.a4.05

[ 7.234008] compat.git: wl18xx.git

[ 7.284484] cfg80211: Calling CRDA to update world regulatory domain

[ 7.547760] wlcore: wl12xx driver version: rowboat-jb-am335x-4.1.2-244-gcf99001-dirty

[ 8.526062] wlcore: wl18xx driver version: rowboat-jb-am335x-4.1.2-244-gcf99001-dirty

[ 8.537353] android_usb: already disabled

[ 8.541778] android_usb: already disabled

[ 8.554901] android_usb: already disabled

[ 8.559906] mtp_bind_config

[ 8.562896] adb_bind_config

root@android:/ # [ 8.640686] adb_open

[ 8.848999] android_work: sent uevent USB_STATE=CONNECTED

[ 8.854766] android_work: sent uevent USB_STATE=DISCONNECTED

[ 8.881042] warning: `rild' uses 32-bit capabilities (legacy support in use)

[ 8.957000] android_work: sent uevent USB_STATE=CONNECTED

[ 8.971923] gadget: high-speed config #1: android

[ 8.977233] android_work: sent uevent USB_STATE=CONFIGURED

[ 52.640899] request_suspend_state: wakeup (3->0) at 52607524981 (2000-01-01 00:00:51.826201713 UTC)

[ 53.312683] net eth0: CPSW phy found : id is : 0x4dd074

[ 53.318969] PHY 0:01 not found

[ 53.343719] ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 53.990478] acc_open

[ 53.992797] acc_release

[ 85.539428] mtp_bind_config

[ 85.542419] adb_bind_config

[ 85.546264] adb_release

[ 85.586669] init: untracked pid 91 exited

[ 85.651672] binder: release 411:592 transaction 5525 out, still active

[ 85.843505] android_work: sent uevent USB_STATE=DISCONECTED

[ 85.882171] android_work: sent uevent USB_STATE=CONNECTED

[ 85.887969] android_work: sent uevent USB_STATE=DISCONNECTED

[ 85.969421] android_work: sent uevent USB_STATE=CONNECTED

[ 85.983489] gadget: high-speed config #1: android

[ 85.988830] android_work: sent uevent USB_STATE=CONFIGURED

[ 86.143768] mtp_open

[ 86.800964] binder: 328:560 transaction failed 29189, size 1544-8

[ 86.807434] binder: send failed reply for transaction 5525, target dead

[ 87.258087] adb_open

[ 88.381072] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit



[ 114.286834] (hci_tty): inside hci_tty_open (ce010648, c3883440)

[ 115.403472] (stk) :line disc installation timed out

[ 117.523406] (stk) :line disc installation timed out

[ 119.643432] (stk) :line disc installation timed out

[ 121.763427] (stk) :line disc installation timed out

[ 123.883392] (stk) :line disc installation timed out

[ 126.003417] (stk) :line disc installation timed out

[ 127.003417] (hci_tty): st_register failed -22

Directory: cfs-file -> key -> telligent-evolution-components-attachments
telligent-evolution-components-attachments -> Unclassified
telligent-evolution-components-attachments -> Texas Instruments Inc x-loader 41. 0-g28b5a696 (Sep 16 2012 16: 24: 04) omap4460: 5 ghz capable som
telligent-evolution-components-attachments -> Texas Instruments Inc x-loader 41. 0-g28b5a696
telligent-evolution-components-attachments -> United States – nato information Sharing (unis) Technical Exchange Meeting (tem) 6 1-3 December 2009 Introduction Site
telligent-evolution-components-attachments -> Japan Earthquake and Tsunami Update Friday, March 18, 2011
telligent-evolution-components-attachments -> My Wilink 8 Part Serial Output on Boot-up
telligent-evolution-components-attachments -> The solid arrow represents Confederate troop movements
telligent-evolution-components-attachments -> Alarm Name Connection Type
telligent-evolution-components-attachments -> Multi-Batch

Download 300.8 Kb.

Share with your friends:
  1   2   3   4   5   6




The database is protected by copyright ©ininet.org 2024
send message

    Main page