Request for Proposals ("erfp")


FRONT AND REAR SPLASH APRONS



Download 0.55 Mb.
Page8/16
Date16.08.2017
Size0.55 Mb.
#33450
TypeRequest
1   ...   4   5   6   7   8   9   10   11   ...   16

FRONT AND REAR SPLASH APRONS


Splash Aprons shall be installed behind the front tires to within 3” of the road surface. Rear splash aprons extend to within 3” of the road surface.

  1. BATTERY COMPARTMENT


A stainless steel battery compartment shall be provided in the roadside to accommodate the size and weight of the batteries. The battery tray shall be vented and will pull out easily.

  1. BUMPERS


Front and rear bumpers shall be reinforced, energy absorbing, type providing protection at speeds of up to 6.5 mph for front impact and 5 mph for rear impact. Bumper material shall be corrosion-resistant and shall withstand repeated impacts of the specified loads without sustaining damage.

  1. PAINT


The entire exterior body surface shall be completely sealed, cleaned, sanded and primed before final finish. The final finish surface shall be low V.O.C. urethane high solids paint meeting all State and Federal Health and Safety Regulations per customer's paint scheme. Complete exterior of the body shall be painted prior to the installation of any exterior access panels, doors, passenger windows and lighting.

  1. EXTERIOR LIGHTING


All exterior lighting shall conform to all State regulations and FMVSS 108.


  1. HEADLAMPS - Dual round sealed beams of counter-sunk automotive type, controlled by a day night run dash mounted switch. The dimmer shall be provided via a steering column mounted control.



  1. FRONT DIRECTIONAL LIGHTS - Front directional lights shall be 4” diameter mounted horizontally, one (1) on each side corner controlled by a steering column mounted level.




  1. STOP AND TAIL LIGHTS - Red lens vertically mounted, 4” diameter in size, one (1) per side.




  1. BACK-UP - White lens vertically mounted 4” diameter in size one (1) per side.




  1. REAR DIRECTIONAL LIGHTS - Amber rear directional lights shall be vertically mounted 4” diameter in size, one (1) per side.




  1. MARKER LIGHTS - Side marker and ICC marker lights shall be roof mounted, five (5) each amber front, and seven (7) each red rear.




  1. ENTRANCE AND EXIT LIGHTS - Entrance and exit lights shall be provided for ADA compliance when applicable.




  1. DOORWAY LIGHTS   Doorway lights shall be suitably mounted so that entire entrance and a portion of the ground area outside the bus shall be sufficiently illuminated. The doorway lights shall be extinguished when the front door is closed.



  1. EXTERIOR LED LIGHTS


LED exterior lights shall be provided at all exterior locations with the exception of the headlights.

  1. SIDE DIRECTIONAL LIGHTS


Side directional lights shall be 1.75" x 4" mounted horizontally on the side of the bus above the front and/or rear tires on each side.

  1. FLOOR MOUNTED DIRECTIONAL SIGNALS

  2. The directional signals shall be floor mounted, to the left of the steering column. This shall allow for hands-free directional signaling.




  1. INTERIOR BODY PANELS


The interior body panels shall be selected from various types of materials providing a light gray color coordinated interior.


  1. SIDE WALL PANELS - Reinforced 1/10” thick laminated melamine panels installed sectional with adhesive and trim moldings.




  1. REAR WALL PANELS - Contoured 1/10” thick laminated melamine panels installed with adhesive and trim moldings.




  1. HEADLINING - Reinforced 1/10” thick laminated melamine panels installed with double face tape and trim molding.



  1. DRIVER’S COAT HOOK AND STRAP


A coat hook and strap for the driver shall be provided within the driver’s compartment.

  1. MODESTY PANELS AND BARRIERS


Modesty panels and barriers shall be ¼ “thick gray melamine fitted to the 1-1/4" O.D. stainless steel tubing passenger assists.


  1. BODY INSULATION


Roof, sidewalls, and rear crown shall be insulated with 2.5" thick fiberglass mat insulation. Mat shall be applied to the inter-surface of the exterior panels. Insulation shall provide maximum thermo-barrier and sound absorption.

  1. ACQ PRESSURE TREATED SUB-FLOOR


Pressure treated, (ACQ treated) 3/4” 7-ply XL Bus Panel preservative treated wood panels shall be manufactured and warranted against fungal decay/ rot, termites and other wood-eating insects. All edges shall be sealed and undercoated prior to installation with sealant caulking and fastened with corrosion resistant Floor-Tight brand huck fasteners.

  1. FLOOR COVERING


RCA Transit rubber flooring, 3/16" ribbed in the aisle and 1/8" smooth under seats, and coved up the sidewalls to the side seat track. Driver's area shall be covered with 1/8" smooth and trimmed with anodized aluminum angle molding. The vestibule shall be covered with 3/16" ribbed rubber and mitered on a 90-degree angle toward the entrance steps. A three-inch (3") wide standee line shall be installed in line with the back edge of the stepwell of contrasting color.

  1. LED INTERIOR LIGHTING


Ceiling cove located I/O Controls or Pretoria brand LED Interior lighting fixtures, mounted continuous front to rear on each side shall be supplied. The first light fixture on each side shall be extinguished when the front door is closed.


  1. Directory: PRSapp -> bid-documents -> EQ Folder
    EQ Folder -> 6 Full Power Racks with Pull Up Bar (Maximum 8 feet tall)
    bid-documents -> Request for Qualifications
    bid-documents -> Invitation to bid your firm is hereby invited to submit to the City of Atlanta, Department of Procurement “dop
    bid-documents -> Invitation to bid your firm is hereby invited to submit to the City of Atlanta, Department of Procurement “dop
    bid-documents -> Wednesday, September 10, 2014 addendum number 1 Solicitation Number: itb 900 15-625 Title: Parking Areas & Decks Cleaning & Sweeping
    bid-documents -> Invitation to bid your firm is hereby invited to submit to the City of Atlanta, Department of Procurement “dop
    bid-documents -> Atlanta Falcons Stadium Company, llc (“Falcons”) Georgia World Congress Center Authority (“Authority”)
    EQ Folder -> Attachment "E"
    EQ Folder -> Georgia department of corrections

    Download 0.55 Mb.

    Share with your friends:
1   ...   4   5   6   7   8   9   10   11   ...   16



The database is protected by copyright ©ininet.org 2024
send message
    Main page
sole responsibility
sole discretion
university system
written consent
closing date
initial term
instructions provided
actual operation
schedule that
official code
estimated value
instructions contained
issue date
public disclosure
public purpose
comments section
state will
lower section
identifying information
applicable terms