Makes approved : PANASONIC / SAMSUNG / LG

2. Should be provisioned with minimum 2 of universal 3-pin type AC socket.

3. Should be provisioned with one 15-pin connector along with 3,5mm jack.

4. Should be provisioned with one HD format signal connector or HDMI type.

5. Should be provisioned with two of RJ45

6. Should be able to flush mount inside the table.

7. Should have design with tilt-up lid.

8. Should have semi-circle cut out on the lid to enable the cables to be used when lid is covered.

9. All the cables should be concealed neatly within the table with easy manual retraction.

Makes approved : EXTRON / KRAMER / EISCONNECT



17

TECHINCAL SPECIFICATIONS FOR AV SOLUTION JOB TO BE UNDERTAKEN FOR M.D.’s ROOM

TECHNICAL SPECIFICATION FOR LED DISPLAY SYSTEM

1.Display of a alteast 49-Inch diagonal display or above.

2.It should have Direct-LED backlight scanning @ 100Hz

3.It should be a Full HD display with 1920 x 1280 pixels

4.Viewing angle should be 178 degree Horizontal / 178 degree Vertical.

5.Should have following video ports:

a.HDMI 1.4 v x 3

b.RCA pin Type x 1

c.RCA x 1

d.HDMI CEC

e.Mini D-sub 15 pin x 1

f.Audio in (Share with AC)

g.USB Type A connector x 1

6.Should have IR, RS232C control ports.

7.Should have built in 10W + 10W speakers with 10% THD.

8.Power requirement of AC 110~240V, 50 Hz / 60 Hz

9.Rated Power consumption of not more than 100W.

10.Stand-by of approx. < 0.5 W

11.Operating Environment 0°C to 40°C temperature, 20% to 80% humidity

Makes approved : PANASONIC / SAMSUNG / LG
TECHNICAL SPECIFICATION FOR WALL MOUNT BRACKET FOR ABOVE LED DISPLAY

Size : Suitable to Mount minimum 48” upto 55” LED Display

Adjustment : Swivel mounting bracket with minimum 6" pull out option Should be able to tilt upto 40 degrees atleast and 20 degrees pan option Wall Mount Screwed Material : Heavy Metal with Powder coat Finish

Makes approved : CHIEF / CUSTOM
TECHNICAL SPECIFICATION FOR CABLE CUBBY MANAGER
1. Should have access for up to six pass through in the device.

2. Should be provisioned with minimum 2 of universal 3-pin type AC socket.

3. Should be provisioned with one 15-pin connector along with 3,5mm jack.

4. Should be provisioned with one HD format signal connector or HDMI type.

5. Should be provisioned with two of RJ45

6. Should be able to flush mount inside the table.

7. Should have design with tilt-up lid.

8. Should have semi-circle cut out on the lid to enable the cables to be used when lid is covered.

9. All the cables should be concealed neatly within the table with easy manual retraction.

Makes approved : EXTRON / KRAMER / EISCONNECT

18

TECHINCAL SPECIFICATIONS FOR AV SOLUTION JOB TO BE UNDERTAKEN FOR TRAINING ROOM
TECHNICAL SPECIFICATION FOR MULTIMEDIA PROJECTOR

1. Projector should be a single chip DLP technology projector

2. It should have native resolution 1280 x 800.

3. It should have minimum 4700 ANSI Lumens brightness, should comply with ISO 21118 international

standards.

4. Should have minimum 1800:1 Contrast ratio.

5. Brightness uniformity should be minimum 85%.

6. Aspect ratio should be 16:10.

7. Vertical optical lens shift should be -30% to +110%.

8. Horizontal optical lens shift should be -10% to +10%

9. Lamp life should be minimum 1,500 hours.

10. Should have following video inputs

1. 
   HDMI, DVI-D, Display Port, 2 x VGA in, VGA out, RGBHV, YUV, S-video
   

12. Operational temperature should be 5-35°C / 41°-95°F.

13. Operational humidity should be 10-85%.

14. Should be certified with following safety certifications

CB test certificate, US emc, US safety, CE emc and safety, CCC emc and safety

Makes approved : BARCO / CHRISTIE / PROJECTION DESIGN

TECHNICAL SPECIFICATION FOR MOTORIZED PROJECTION SCREEN
1. Projection screen for the size of 110" diagonally sized

2. Aspect ratio 16:9 wide format motor type screen with two-way switch

3. To have pre-set but adjustable limit switches to automatically stop picture surface in the “up” and

“down” positions.

4. Should be electrically operated 120 volt (60 Hz) not more than 2.4 amp

5. The roller to be of rigid metal

6. Matte white screen fabric, flame-retardants with black masking borders.

7. Should be supplied with three-position control switch with cover plate.

2. Bracket mounting rod to be with adjustable with tilt and height of minimum 24” up to 48”

3. The rod and bracket should be powder coated suitable for lasting durability.

Makes approved : CHIEF / nT / LIBERTY
19

TECHNICAL SPECIFICATION FOR CEILING MOUNT SPEAKERS
Component: 200 mm (8 in) Full-Range

Frequency Range (-10 dB): 50 Hz – 16 kHz

Coverage: 90° conical

Sensitivity (2.83V@ 1m): 97 dB (1 kHz - 8 kHz)

Termination: Bare Wire

Nominal Driver Impedance: 8 ohms

Driver Power Capacity: 25 W

70V/100V Transformer Taps: 6 W, 3 W, 1.5 W, (0.75 W at 70 V only)

Dimensions (Diameter x Depth): 287 mm (11.3 in) diameter round baffle x 104 mm (4.1 in) depth from back

Cutout Dimension: 260 mm diameter (10.1 in)

Should have Clear, High-Fidelity Performance
Makes approved : BOSE / JBL / EXTRON
TECHNICAL SPECIFICATION FOR MIXER AUDIO AMPLIFIER

• 
  240 Watt professional public address units with 230 VAC ±10%, 50/60 Hz (reduced power at lower mains voltage)
  
• 
  Frequency response : 60 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB for Line input and 70 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB for mic input
  
• 
  Signal to Noise Ratio >63 dB (mic.); >70 dB (line) at max volume
  
• 
  Phantom power supply : 16 V via 1.2 kohm (mic.)
  

• 
  Wireless transmitter type Cardioid Dynamic Vocal Microphone with an on/off switch
  
• 
  Frequency response 60 to 15,000 Hz • Sensitivity (@ 1kHz) -53 dBV/Pa, (2.2 mV), 94 dB SPL
  
• 
  Three-pin professional audio connector (male XLR type)
  
• 
  Wireless receiver type Single channel receiver for vocal microphones
  
• 
  Upto 8 selectable channels and upto 4 compatible systems
  
• 
  Mic / Line Switch
  
• 
  Receiver should have 1/4” output & XLR output connectors
  

• 
  Wireless transmitter type Condenser lavalier microphone
  
• 
  Frequency response 50 to 20,000 Hz
  
• 
  Unidirectional polar patter
  
• 
  600 Ω Output Impedance @ 1 kHz, typical
  
• 
  72 dB Signal-To-Noise Ratio @ 1 kHz
  

• 
  139 dB maximum SPL 1000 Ω load, @ 3% THD
  
• 
  Operating Range: Up to 75 Meters
  
• 
  Wireless receiver with body-pack transmitter with upto 10hours battery
  
• 
  Up to 8 selectable channels and up to 4 compatible systems
  
• 
  Mic / Line Switch
  
• 
  Receiver should have 1/4”, XLR output connectors
  

• 
  AVplate is required to be mounted with 15-pin VGA along with 3.5mm Audio connectors, each for PC/Laptop presentation
  
• 
  Cable to be managed with external patch cables connectivity type
  

HDMI : Extron / Crestron / MX - All HDMI cables to be capable of High Resolution Signals

Audio / Mic / VGA / Speaker : Extron / Crestron

Should be supplied as per the room connectivity requirement.

• 
  Vendor should be either Manufacturer or Distributor or Authorized Dealer with Valid Authorization certificate from OEM to quote in this tender, importantly for
  
  • 
    Projector,
    
  • 
    Switching System
    
  • 
    Wireless Presenter
    
  • 
    Table Top Mics
    
  • 
    Digital Signal Processor,
    
  • 
    Control Processor etc
    
• 
  The vendor should have ClearOne/BiAmp/Crestron certified engineers & Programmers.
  
• 
  Turnover should be above 3 Crs for last 3 years.
  
• 
  Proof of past supply of similar equipment’s to other Govt / Public Sector or reputed Corporate organizations, PO copies & Completion certificates to be attached.