At any time that the phone is running, if a network capture is taking place (by means of tcpdump) and hence, call might be recorded (by capturing the RTP payload) the value of RECSTAT should be set to “1”. Otherwise it should be set to “0”.
96x1H-IPI.5.1.1000: Audio stream encoding (codecs and compression)
Approved
Audio streams will be transmitted and received via RTP or SRTP (see 96x1H-IPI.5.1.900).
Encoding and decoding of 64 kbit/sec (8-bit sample) mu-law and A-law audio streams will be supported according to ITU-T Recommendation G.711 [7.4-4].
Note:
G.711 mu-law and A-law are the only audio coding algorithms required by H.323 (Section 6.2.5).
Note:
G.711 recommends a tolerance of ±50 parts per million on its 8kHz sampling rate.
Rationale:
H.225.0 Section 6.2.1 states that only 64 kbit/sec (as opposed to 48 or 56 kbit/sec) G.711 shall be used on packet-based networks.
Approved
For intervals of missing G.711 samples, the contents of the last audio frame will be repeated once and then comfort noise will be generated based on an estimate of the recent received noise floor. The volume will be ramped down and then back up during the transitions to prevent pops and clicks.
Rationale:
The non-standard silence suppression mode for G.711 is intended to address customer’s desires for a lower-bandwidth mode for G.711 while retaining compatibility with the Avaya IP Softphone, the Definity Prowler media processing board and with Microsoft’s NetMeeting application. Transmission of G.711 Appendix II SID frames should not be done until it can be explicitly invoked. RFC 3389 [7.3-22c] specifies an RTP Payload Type of 13 for Comfort Noise packets.
Approved
Encoding and decoding of audio streams will be supported according to ITU-T Recommendation G.722 [7.4-5] at a rate of 64 Kbps.
Rationale:
H.225.0 Section 6.2.1 states that only 64 kbit/sec (as opposed to 48 or 56 kbit/sec) G.722 shall be used on packet-based networks.
Approved
Encoding and decoding of audio streams will be supported according to ITU-T Recommendation G.726A [7.4-10a] at a rate of 32 Kbps.
Encoding of audio streams will be supported according to ITU-T Recommendations G.729A [7.4-11a] or G.729B [7.4-11b] used with G.729A (sometimes called G.729AB), and the decoding of audio streams will be supported according to G.729B used with G.729A (i.e., only the low-complexity encoder will be supported, but audio streams will be able to be generated either with or without silence suppression, and Silence Insertion Descriptor (SID) frames will always be supported if received during decoding).
Note:
G.729B provides silence suppression and comfort noise generation, but G.729 and G.729A do not. G.729A is a reduced-complexity version of G.729 (i.e., it takes less processing power to implement and may result in lower audio quality), but each is able to decode a bit-stream encoded by the other.
Rationale:
Silence Insertion Descriptor (SID) frames will always be supported if received during G.729 decoding because the RTP payload type (see 96x1H-IPI.5.1.900) does not distinguish between streams with and without silence suppression.
Approved
A silence suppression mode will be supported for all codecs except G.729B. When the silence suppression mode is activated and silence is detected, no audio data or SID frames will be transmitted.
Rationale:
The non-standard silence suppression mode for G.729 (i.e., G.729B without SID frames) is intended for compatibility with the IP Softphone.
Note:
H.323 signaling is responsible for negotiating which codecs can be used between endpoints. The codec to be used for audio decoding is indicated in the received RTP header (see 96x1H-IPI.5.1.900). One of the following codecs must be specified for encoding and transmission, any of which may also be encrypted:
G.711 mu-law
G.711 A-law
G.711 mu-law with silence suppression
G.711 A-law with silence suppression
G.722-64
G.722-64 with silence suppression
G.726A-32
G.726A-32 with silence suppression
G.729A
G.729A with silence suppression (without SID frames)
G.729B used with G.729A (with SID frames, sometimes called G.729AB)
Rationale:
G.723 is not supported because it results in lower audio quality than G.729, and customers haven’t expressed a need for it.
96x1H-IPI.5.1.1100: Simple Network Management Protocol (SNMP) and Management Information Base (MIB)
Approved
An SNMP Version 2c (SNMPv2c) agent will be supported as specified in the non-SNMPv3-specific parts of IETF STD 62 (RFCs 3411-3413 and 3415-3418) and RFC 3584 [7.3-12a,b,c,e,f,g,h,i],
SMIv2 as specified by STD 58 (RFC 2578) and RFCs 2579 and 2580 [7.3-13a,b,c],
MIB-II as specified in IETF STD 17 (RFC 1213) and RFCs 2863, 3418, 4022, 4113, and 4293
[7.3-14c,d,e,f,g] and [7.3-12h], as well as the custom MIB and other clarifications as specified below.
SNMP will use UDP (see 96x1H-IPI.5.1.400) as a transport-layer protocol. The UDP port will be opened for the reception of SNMP messages if and only if the value of the parameter SNMPSTRING is not null.
Note:
The UDP port numbers used for SNMP are specified in 96x1H-IPI.5.1.400.
Approved
A message will be sent in response to any valid SNMP query from any source if the value of the parameter SNMPADD is null, but only if the source IP address of the query matches one of the IP addresses contained by SNMPADD if SNMPADD is not null, and only if the community string in the query matches the value of the parameter SNMPSTRING, but need not respond to more than one such query per second. Responses to SNMPv1 queries will be as specified in Section 4 of RFC 2576.
Rationale:
The telephone is only required to respond to 1 SNMP query per second to enable it to improve its resilience to denial of service attacks (see 96x1H-IPI.5.2.200).
Responses to SNMPv1 queries are supported because some management systems still use SNMPv1. SNMPv3 queries look just like SNMPv2 queries, so no additional support is required.
Approved
SNMP queries will not be initiated and SNMP notification (traps) will not be supported.
The following MIB-II groups will be supported, except that writable objects are not required to be writable, but if they are writable, written values will not affect operation of the telephone:
Group Name
Reference
Group OID (the OID for MIB-II is 1.3.6.1.2.1)
System
(RFC 3418)
1.3.6.1.2.1.1
Interfaces
(RFC 2863)
1.3.6.1.2.1.2
IP
(RFC 4293)
1.3.6.1.2.1.4
ICMP
(RFC 4293)
1.3.6.1.2.1.5
TCP
(RFC 4022)
1.3.6.1.2.1.6
UDP
(RFC 4113)
1.3.6.1.2.1.7
SNMP
(RFC 3418)
1.3.6.1.2.1.11
and will not support the following groups:
Address Translations
1.3.6.1.2.1.3
EGP
1.3.6.1.2.1.8
CMOT
1.3.6.1.2.1.9
Transmission
1.3.6.1.2.1.10
Rationale:
The MIB does not include the MIB-II EGP group because the IP telephones do not support EGP (Exterior Gateway Protocol), and it does not include the Transmission group because definitions for transmission media have not been approved by standards organizations.
Approved
The value of the sysObjectID object in the MIB-II System group (1.3.6.1.2.1.1.2) will be as specified in the following table:
Model Name(s)
sysObjectID
9608
1.3.6.1.4.1.6889.1.69.5.1
9611
1.3.6.1.4.1.6889.1.69.5.2
9621
1.3.6.1.4.1.6889.1.69.5.3
9641
1.3.6.1.4.1.6889.1.69.5.4
Note:
The sysObjectIDs correspond to the MIB addressing scheme specified below. Following Avaya’s Enterprise identifier (6889), the nodes represent AvayaProducts (1), IP Endpoint Products (69), 96x1 H.323 IP Telephones (5), and an identifier for the phone model.
Approved
The value of the ipForwarding object in the MIB-II IP group will be 2 (i.e., NOT acting as a router).
The value of the sysName object in the MIB-II System group (1.3.6.1.2.1.1.5) will be the same as the Host Name specified for DHCP option 12 (see 96x1H-IPI.5.1.604).
The value of the ifSpeed object in the first entry of the ifTable object in the MIB-II Interfaces group (1.3.6.1.2.1.2.2.1.5) will be set to the operating speed of the Ethernet line interface.
The value of the ifSpeed object in the second entry of the ifTable object in the MIB-II Interfaces group (1.3.6.1.2.1.2.2.1.5) will be set to the operating speed of the secondary Ethernet interface.
The MIB addressing scheme shown below will be supported.
All objects are “read-only” access and “mandatory” status.
iso
1
org
3
dod
6
internet
1
private
4
enterprises
1
avaya
6889
avayaMibs
2
ipEndpointMIBs
69
avaya96x1HMIB
5 Note that 46xx/56xx telephones use a value of 1 here,
96xx H.323 (SPICE) telephones use a value of 2,
16xx (Sage) telephones use a value of 3,
96xx SIP (Spark) telephones use a value of 4,
96x1 SIP telephones use a value of 6,
ADVD (Mojo) telephones use a value of 7, and
B189 H.323 speakerphones use a value of 8.
endptID
1
endptNVM
2
endptMaintenance
3
endptApps
4
endptAdjuncts
5
endptH323
6
reserved
7
endptCERT
8
endptVPN
9
Rationale:
SNMP needs MIBs to function, and the basic, required MIB defined in MIB-II is insufficient for tracking the details required for the IP telephones. As allowed by the SNMP protocol, custom MIBs such as the one specified above are the standard tool for expanding on the basic MIB. The term “endpoint” was chosen rather than “telephone” to allow maximum flexibility in expanding the MIB to cover future product directions.
GROUP 1: endptID This group contains objects referring to the current operational state and functionality of the endpoint. Parameters referred to in a Definition are from Section 2.1 of this document unless otherwise indicated.
Current value of AGCHAND converted to integer format.
endptAGCHEAD
Integer
Current value of AGCHEAD converted to integer format.
endptAGCSPKR
Integer
Current value of AGCSPKR converted to integer format.
endptAPPINUSE
DisplayString
Current value of APPINUSE.
endptAPPNAME
DisplayString
Current value of APPNAME.
endptAUDIOENV
Integer
Current value of AUDIOENV converted to integer format.
endptAUDIOSTHD
Integer
Current value of AUDIOSTHD converted to integer format.
endptAUDIOSTHS
Integer
Current value of AUDIOSTHS converted to integer format.
endptAUTOANSSTAT
Integer
Current value of AUTOANSSTAT converted to integer format.
(Approved for R6.2.2+)
endptAUTOANSSTRING
DisplayString
Current value of AUTOANSSTRING. (Approved for R6.2.2+)
endptBAKLIGHTOFF
Integer
Current value of BAKLIGHTOFF converted to integer format.
endptBACKUPAPP
DisplayString
Current value of BACKUPAPP.
endptBOOT1INUSE
DisplayString
Current value of BOOT1INUSE.
endptBOOT2INUSE
DisplayString
Current value of BOOT2INUSE.
endptBRAUTH
Integer
Current value of BRAUTH converted to integer format.
endptBRURI
DisplayString
Current value of BRURI.
endptCNAPORT
Integer
Current value of CNAPORT converted to integer format. (pre-R6.2 only)
endptCNASRVR
DisplayString
Current value of CNASRVR. (pre-R6.2 only)
endptCODECR
DisplayString
Current value of CODECR.
endptCODECT
DisplayString
Current value of CODECT.
endptDHCPINUSE
IPAddress
IP address of the DHCP server from which IPADD was obtained; 0.0.0.0 if IPADD was not obtained via DHCP.
endptDHCPINUSEV6
DisplayString
IP address of the DHCPv6 server from which IPADDV6 was obtained, converted to ASCII colon-hex format; “::” if IPADDV6 was not obtained via DHCPv6.
endptDHCPLEASEEXP
Integer32
Time remaining (in seconds) until the expiration of the IPv4 address lease, zero if expired.
endptDHCPLEASEREBIND
Integer32
Interval (in seconds) from IP address assignment until the DHCP REBINDING state is entered (32-bit unsigned integer, as received in DHCP option 59), or as computed from the lease time, if option 59 is not received.
endptDHCPLEASERENEW
Integer32
Interval (in seconds) from IP address assignment until the DHCP RENEWING state is entered (32-bit unsigned integer, as received in DHCP option 58), or as computed from the lease time, if option 58 is not received.
endptDHCPLEASETIME
Integer32
Duration (in seconds) of IPADD lease (32-bit unsigned integer, as received in DHCP option 51).
endptDHCPPREF
DisplayString
Current value of DHCPPREF.
endptDHCPSTAT
Integer
Current value of DHCPSTAT converted to integer format.
endptDHCPSTD
Integer
Current value of DHCPSTD converted to integer format.
endptDHCPT1REM
Integer32
Time remaining (in seconds) until the start of IPv4 address lease renewal (i.e., until the expiration of timer T1), zero if expired and -1 if the lease is infinite.
endptDHCPT2REM
Integer32
Time remaining (in seconds) until the start of IPv4 address lease rebinding (i.e., until the expiration of timer T2), zero if expired, zero if expired and -1 if the lease is infinite.
endptDHCPV6LEASEEXP
Integer32
Time remaining (in seconds) until the expiration of the IPv6 address lease, zero if expired.
endptDHCPV6LIFEPREF
Integer32
The preferred-lifetime value received in the DHCPv6 IA Address option.
endptDHCPV6LIFEVALID
Integer32
The valid-lifetime value received in the DHCPv6 IA Address option.
endptDHCPV6T1
Integer32
The T1 value received in the DHCPv6 IA_NA option.
endptDHCPV6T1REM
Integer32
Time remaining (in seconds) until the start of IPv6 address lease renewal (i.e., until the expiration of timer T1), zero if expired and -1 if the lease is infinite.
endptDHCPV6T2
Integer32
The T2 value received in the DHCPv6 IA_NA option.
endptDHCPV6T2REM
Integer32
Time remaining (in seconds) until the start of IPv6 address lease rebinding (i.e., until the expiration of timer T2), zero if expired, zero if expired and -1 if the lease is infinite.
endptDNSSRVR
DisplayString
Current value of DNSSRVR.
endptDOMAIN
DisplayString
Current value of DOMAIN.
endptDOT1X
Integer
Current value of DOT1X converted to integer format.
endptDOT1XSTAT
Integer
Current value of DOT1XSTAT converted to integer format.
endptDSCPAUD
Integer
Current value of DSCPAUD converted to integer format.
endptDSCPBBE
Integer
Current value of DSCPBBE converted to integer format.
endptDSCPSIG
Integer
Current value of DSCPSIG converted to integer format.
endptDSPVERSION
DisplayString
Up-to-10-character identifier of the version of the current DSP firmware.
endptFEIPADD
DisplayString
Current value of FEIPADD.
endptFEPORT
Integer
Current value of FEPORT converted to integer format.
endptFONT
DisplayString
The string “Built-in”.
endptGIPADD
DisplayString
Current value of GIPADD.
endptGIPINUSE
IPAddress
IP address of the IPv4 router currently in use.
endptGIPINUSEV6
DisplayString
IP address of the IPv6 router currently in use, converted to ASCII colon-hex format.
endptGRATARP
Integer
Current value of GRATARP converted to integer format.
endptGRATNAV6
Integer
Current value of GRATNAV6 converted to integer format.
endptGROUP
Integer
Current value of GROUP converted to integer format.
endptHTTPDIR
DisplayString
Current value of HTTPDIR.
endptHTTPPORT
Integer
Current value of HTTPPORT converted to integer format.
endptHTTPSRVR
DisplayString
Current value of HTTPSRVR.
endptHTTPUSED
DisplayString
IP address from HTTPSRVR, if any, successfully used during initialization (all zeroes if no server from HTTPSRVR was successfully used during initialization).
endptHWVERSION
Integer
Hardware Vintage number (see 9xxxHW.2.6.100 in [7.1-2]), also known as the Hardware Version field in the EEPROM.
(Approved only for release R6.4+)
endptICMPDU
Integer
Current value of ICMPDU converted to integer format.
endptICMPRED
Integer
Current value of ICMPRED converted to integer format.
endptIPADD
IPAddress
Current value of IPADD converted to IPAddress format.
endptIPADDV6
DisplayString
Current value of IPADDV6.
endptIPADDV6LL
DisplayString
Current value of IPADDV6LL.
endptIPPREF
Integer
Current value of IPPREF converted to integer format.
endptIPV6STAT
Integer
Current value of IPV6STAT converted to integer format.
endptJMSEC
Integer
Current value of JMSEC converted to integer format.
endptL2Q
Integer
Current value of L2Q converted to integer format.
endptL2QAUD
Integer
Current value of L2QAUD converted to integer format.
endptL2QSIG
Integer
Current value of L2QSIG converted to integer format.
endptL2QSTAT
Integer
0 if 802.1Q tagging is currently OFF, else 1.
endptL2QVLAN
Integer
Current value of L2QVLAN converted to integer format.
endptL2QVLANINUSE
Integer
Current 802.1Q VLAN IDentifier value, (0 if 802.1Q tagging is off).
endptLANGFILES
DisplayString
A comma-separated list of the language files stored in the telephone, if any.
The number of bytes of volatile memory currently allocated for, but unused by, the Heap.
endptMODEL
DisplayString
Current value of MODEL.
endptNDREDV6
Integer
Current value of NDREDV6 converted to integer format.
endptNETMASK
IPAddress
Current value of NETMASK converted to IPAddress format.
endptPHNEMERGNUM
DisplayString
Current value of PHNEMERGNUM.
endptPHONECC
DisplayString
9-numeric-character comcode/Part ID of the endpoint.
endptPHONESN
DisplayString
Up-to-18-character serial number as labeled on the outside of the endpoint.
endptPHY1DUPLEX
Integer
Current duplex of the Ethernet line interface,
either 1 if half-duplex or 2 if full-duplex.
endptPHY1SPEED
Integer
Current speed of the Ethernet line interface in Mbps.
endptPHY1STAT
Integer
Current value of PHY1STAT converted to integer format.
endptPHY2AUTOMDIXENABLED
Integer
Current value of PHY2_AUTOMDIX_ENABLED converted to integer format. (Approved for R6.3+)
endptPHY2DUPLEX
Integer
Current duplex of the secondary Ethernet interface,
either 0 if no link is established, 1 if half-duplex or 2 if full-duplex.
endptPHY2PRIO
Integer
Current value of PHY2PRIO converted to integer format
endptPHY2SPEED
Integer
Current speed of the secondary Ethernet interface in Mbps,
either 0, 10 or 100.
endptPHY2STAT
Integer
Current value of PHY2STAT converted to integer format
(0 if the telephone does not have a secondary Ethernet interface).
endptPHY2VLAN
Integer
Current value of PHY2VLAN converted to integer format.
endptPINGREPLYV6
Integer
Current value of PINGREPLYV6 converted to integer format.
endptPORTAUD
Integer
Current value of PORTAUD converted to integer format.
endptPROCPSWD
Integer
0 if PROCPSWD is currently null, else 1.
(Obsolete (0) for R6.2.4+)
endptPROCSTAT
Integer
Current value of PROCSTAT converted to integer format.
endptPWBCC
DisplayString
Current value of PWBCC.
(Obsolete (null) for R6.3+)
endptPWBSN
DisplayString
Up-to-18-character printed wiring board serial number of the endpoint or the string “N/A” if the printed wiring board does not have a serial number.
(Obsolete (null) for R6.3+)
endptRFSINUSE
DisplayString
Current value of RFSINUSE.
endptRFSNAME
DisplayString
Current value of RFSNAME.
endptRSVPCONT
Integer
Current value of RSVPCONT converted to integer format.
endptRSVPPROF
Integer
Current value of RSVPPROF converted to integer format.
endptRSVPRFRSH
Integer
Current value of RSVPRFRSH converted to integer format.
endptRSVPRTRY
Integer
Current value of RSVPRTRY converted to integer format.
endptRTCPCONT
Integer
Current value of RTCPCONT converted to integer format.
endptRTCPFLOW
Integer
Current value of RTCPFLOW converted to integer format.
endptRTCPMON
DisplayString
Current value of RTCPMON.
endptSIG
Integer
Current value of SIG converted to integer format.
endptSNMPADD
DisplayString
Current value of SNMPADD
endptSSONCONTENT
DisplayString
The data portion of the DHCP site-specific option designated by NVSSON (see 96x1H-IPI.5.1.604), exactly as received.
endptSTATIC
Integer
Current value of STATIC converted to integer format
endptTLSDIR
DisplayString
Current value of TLSDIR.
endptTLSPORT
Integer
Current value of TLSPORT converted to integer format.
endptTLSSRVR
DisplayString
Current value of TLSSRVR
endptTLSSRVRID
Integer
Current value of TLSSRVRID converted to integer format.
endptTLSUSED
DisplayString
IP address from TLSSRVR, if any, successfully used during initialization (all zeroes if no server from TLSSRVR was successfully used during initialization)
endptTMSEC
Integer
Current value of TMSEC converted to integer format.
endptTRUSTCERTS
DisplayString
Current value of TRUSTCERTS.
endptVLANLIST
DisplayString
Current value of VLANLIST.
Note: This object will not be valid until after H.323 procedures update VLANLIST from NVVLANLIST after registration.
endptVLANSEP
Integer
Current value of VLANSEP converted to integer format
endptVOXFILES
DisplayString
Current value of VOXFILES.
(Approved only for releases prior to R6.3, Obsolete (null) for R6.3+)
endptVSICONTENT
DisplayString
The option-data portion of vendor-specific option 242, exactly as received in the DHCPv6 Vendor-Specific Information option (see 96x1H-IPI.5.1.606).
GROUP 2: endptNVM This group contains objects referring to persistent parameters of the endpoint as stored in non-volatile memory, which will not necessarily match the current endpoint state or functionality. Persistent parameters referred to in a Definition are from Section 2.1 of this document unless otherwise indicated.
Object Identifier
Syntax
Definition
endptNVAGCHAND
Integer
Current value of NVAGCHAND converted to integer format.
endptNVAGCHEAD
Integer
Current value of NVAGCHEAD converted to integer format.
endptNVAGCSPKR
Integer
Current value of NVAGCSPKR converted to integer format.
endptNVALERT
Integer
Obsolete: not supported.
endptNVAUTH
Integer
Current value of NVAUTH converted to integer format.
endptNVBM1BRIGHTNESS
Integer
Current value of NVBM1BRIGHTNESS converted to integer format.
endptNVBM2BRIGHTNESS
Integer
Current value of NVBM2BRIGHTNESS converted to integer format.
endptNVBM3BRIGHTNESS
Integer
Current value of NVBM3BRIGHTNESS converted to integer format.
endptNVBRIGHTNESS
Integer
Current value of NVBRIGHTNESS converted to integer format.
endptNVCONTRAST
Integer
Current value of NVCONTRAST converted to integer format.
endptNVGIPADD
IPAddress
Current value of NVGIPADD converted to IPAddress format.
endptNVIPADD
IPAddress
Current value of NVIPADD converted to IPAddress format.
endptNVIPADDV6
DisplayString
Current value of NVIPADDV6.
endptNVL2Q
Integer
Current value of L2Q converted to integer format.
endptNVL2QVLAN
Integer
Current value of NVL2QVLAN converted to integer format.
endptNVLANGFILE
DisplayString
Current value of NVLANGFILE.
endptNVLOGSTAT
Integer
Current value of NVLOGSTAT converted to integer format.
endptNVNETMASK
IPAddress
Current value of NVNETMASK converted to IPAddress format.
endptNVPHY1STAT
Integer
Current value of PHY1STAT converted to integer format.
endptNVPHY2STAT
Integer
Current value of PHY2STAT converted to integer format
(0 if the telephone does not have a secondary Ethernet interface).
endptNVRINGTONESTYLE
Integer
Current value of RINGTONESTYLE converted to integer format.
endptNVSSON
Integer
Current value of NVSSON converted to integer format.
endptNVTRUSTLIST
DisplayString
Current value of NVTRUSTLIST.
endptNVVLANTEST
Integer
Current value of VLANTEST converted to integer format.
endptNVVOXFILE
DisplayString
Current value of NVVOXFILE.
(Approved only for releases prior to R6.3, Obsolete (null) for R6.3+)
GROUP 3: endptMaintenance This group contains objects relevant to the maintenance and trouble-shooting of the endpoint, beyond the standard objects specified in MIB-II. Persistent parameters referred to in a Definition are from Section 2.1 of this document unless otherwise indicated.
Object Identifier
Syntax
Definition
endptAPPstat
Integer
0 if the value of APPNAME is null;
1 if the most recent attempt to download APPNAME was not successful;
2 if the most recent attempt to download APPNAME was successful, but the file was too large;
3 if the most recent attempt to download APPNAME was successful, but the file type was incorrect;
5 if the most recent attempt to download APPNAME was successful, but was not valid for the telephone hardware;
6 if the most recent attempt to download APPNAME was successful, but it was not compatible with the new Kernel/RFS software package;
7 if the most recent attempt to download APPNAME was successful, but it was not compatible with the existing Kernel/RFS software package;
8 if the most recent attempt to download APPNAME was successful, but the existing Kernel/RFS software package was not compatible with it;
9 if the most recent attempt to download APPNAME was successful.
endptRFSstat
Integer
0 if the value of RFSNAME is null;
1 if the most recent attempt to download RFSNAME was not successful;
2 if the most recent attempt to download RFSNAME was successful, but the file was too large;
3 if the most recent attempt to download RFSNAME was successful, but the file type was incorrect;
4 if the most recent attempt to download RFSNAME was successful, but files were missing, had the wrong file type, or had invalid signatures;
5 if the most recent attempt to download RFSNAME was successful, but was not valid for the telephone hardware;
6 if the most recent attempt to download a RFSNAME was successful, but it was not compatible with the new Application/Library software package;
7 if the most recent attempt to download RFSNAME was successful, but it was not compatible with the existing Application/Library software package;
8 if the most recent attempt to download RFSNAME was successful, but the existing Application/Library software package was not compatible with it;
9 if the most recent attempt to download RFSNAME was successful.
endptUpgradeStat
Integer
0 if a 96x1Hupgrade.txt configuration file was successfully obtained and interpreted after the last power-up or reset;
1 if a 96x1Hupgrade.txt configuration file was successfully obtained but an error occurred during its interpretation; and
2 if a 96x1Hupgrade.txt configuration file was not successfully obtained.
endptRecentLog
SEQUENCE DisplayString
Contains up to the last 500 log event records (see 96x1H-IPI.5.1.1300) with a numeric severity code that is less than the value of LOGLOCAL that were generated by the software since the last reset or power-up, in order, starting with the oldest, whether or not the messages were sent to a syslog server.
endptResetLog
SEQUENCE DisplayString
Contains up to the last 500 log event records (see 96x1H-IPI.5.1.1300) with a numeric severity code that is less than the value of LOGLOCAL that were generated by the software before the last reset (if there has been a reset since the last power-up), in order, starting with the oldest, whether or not the messages were sent to a syslog server.
endptStartupLog
SEQUENCE DisplayString
Contains up to the first 500 log event records (see 96x1H-IPI.5.1.1300) with a numeric severity code that is less than the value of LOGLOCAL that were generated by the software after the last power-up or reset, in order, starting with the oldest, whether or not the messages were sent to a syslog server.
endptSSHStatus
Integer
Current value of SSH_STATUS converted to integer format, approved for R6.4+.
Note:
RFC 2579 only allows SNMP MIB DisplayString objects to contain up to 255 characters, so if a syslog message is longer than 255 characters, the entire message cannot be saved in a DisplayString object.
GROUP 4: endptApps This group contains objects associated with applications.
Object Identifier
Syntax
Definition
endptAPPSTATVALUE
Integer
Current value of APPSTAT converted to integer format.
endptAUDIOPATH
Integer
Current value of OPTAUDIOPATH (see 96x1LA.5.3.2000 in [7.1-5]) converted to integer format.
endptCLDELCALLBK
Integer
Current value of CLDELCALLBK converted to integer format.
endptENHDIALSTAT
Integer
Current value of ENHDIALSTAT converted to integer format.
endptFBONCASCREEN
Integer
Current value of FBONCASCREEN converted to integer format.
endptGUESTDURATION
Integer
Current value of GUESTDURATION converted to integer format.
endptGUESTLOGINSTAT
Integer
Current value of GUESTLOGINSTAT converted to integer format.
endptGUESTWARNING
Integer
Current value of GUESTWARNING converted to integer format.
endptLOGBACKUP
Integer
Current value of LOGBACKUP converted to integer format.
endptLOGMISSEDONCE
Integer
Current value of LOGMISSEDONCE converted to integer format.
endptLOGUNSEEN
Integer
Current value of LOGUNSEEN converted to integer format.
endptOPSTAT
Integer
Current value of OPSTAT converted to integer format.
endptOPSTAT2
Integer
Current value of OPSTAT2 converted to integer format.
endptPUSHCAP
DisplayString
Current value of PUSHCAP.
endptPUSHPORT
Integer
Current value of PUSHPORT converted to integer format.
endptQKLOGINSTAT
Integer
Current value of QKLOGINSTAT converted to integer format.
endptSCREENSAVER
DisplayString
Current value of SCREENSAVER.
endptSUBSCRIBELIST
DisplayString
Current value of SUBSCRIBELIST.
endptTPSLIST
DisplayString
Current value of TPSLIST.
endptWMLEXCEPT
DisplayString
Current value of WMLEXCEPT.
endptWMLHOME
DisplayString
Current value of WMLHOME.
endptWMLIDLETIME
Integer
Current value of WMLIDLETIME converted to integer format.
endptWMLIDLEURI
DisplayString
Current value of WMLIDLEURI.
endptWMLPORT
Integer
Current value of WMLPORT converted to integer format.
endptWMLPROXY
DisplayString
Current value of WMLPROXY.
GROUP 5: endptAdjuncts This group contains objects associated with telephone adjuncts.
Object Identifier
Syntax
Definition
endptBM1HWVER
DisplayString
The hardware version (see 96x1COPS.8.2.300 in [7.1-4]) of the first button module if one is attached, converted to DisplayString format, otherwise null.
endptBM1SWVER
DisplayString
The software version (see 96x1COPS.8.2.300 in [7.1-4]) of the first button module if one is attached, otherwise null.
endptBM2HWVER
DisplayString
The hardware version (see 96x1COPS.8.2.300 in [7.1-4]) of the second button module if one is attached, converted to DisplayString format, otherwise null.
endptBM2SWVER
DisplayString
The software version (see 96x1COPS.8.2.300 in [7.1-4]) of the second button module if one is attached, otherwise null.
endptBM3HWVER
DisplayString
The hardware version (see 96x1COPS.8.2.300 in [7.1-4]) of the third button module if one is attached, converted to DisplayString format, otherwise null.
endptBM3SWVER
DisplayString
The software version (see 96x1COPS.8.2.300 in [7.1-4]) of the third button module if one is attached, otherwise null.
endptBMODS
Integer
The number of button modules detected by the telephone.
endptUSBPOWER
Integer
Current value of USBPOWER converted to integer format.
Note:
Requirements for the hardware version and software version (file name) are specified in [7.1-4].
GROUP 6: endptH323 This group contains values related to the H.323 signaling protocol.
Object Identifier
Syntax
Definition
endptGKINUSE
DisplayString
IP address of the gatekeeper with which the telephone is currently registered (all zeroes if the telephone is not currently registered with a gatekeeper), see 96x1Tel.2.1.400 and 96x1Tel.2.1.500 in [7.1-6].
endptGKTCPPORT
Integer
0 if the telephone is not currently registered with a gatekeeper, otherwise the TCP port number on the gateway with which the telephone has a signaling connection established.
endptMCIPADD
DisplayString
Current value of MCIPADD, see 96x1Tel.2.1.300 in [7.1-6].
endptNVPHONEXT
DisplayString
The telephone extension number stored in non-volatile memory, see 96x1Tel.2.1.400 and 96x1Tel.2.1.500 in [7.1-6].
endptRASGKList
DisplayString
SEQUENCE
Current RAS Gatekeeper List provided by the call server, null if such a list was not provided, see 96x1Tel.2.1.300 in [7.1-6].
endptREREGISTER
Integer
Current value of REREGISTER converted to integer format, see 96x1H-IPI.2.1.900, and 96x1Tel.2.1.400 and 96x1Tel.2.1.500 in [7.1-6].
endptSERVICESTAT
Integer
Current value of SERVICESTAT converted to integer format, see 96x1Tel.2.1.210, 96x1Tel.2.1.300, 96x1Tel.2.1.400 and 96x1Tel.2.1.500 in [7.1-6].
GROUP 7:Reserved
GROUP 8: endptCERT This group will be supported only by telephones that support an identity certificate.
Object Identifier
Syntax
Definition
endptMYCERTCAID
DisplayString
Current value of MYCERTCAID.
endptMYCERTCN
DisplayString
Current value of MYCERTCN.
endptMYCERTDN
DisplayString
Current value of MYCERTDN.
endptMYCERTKEYLEN
Integer
Current value of MYCERTKEYLEN converted to integer format.
endptMYCERTRENEW
Integer
Current value of MYCERTRENEW converted to integer format.
endptMYCERTURL
DisplayString
Current value of MYCERTURL.
endptMYCERTWAIT
Integer
Current value of MYCERTWAIT converted to integer format.
GROUP 9: endptVPN This group will be supported only by telephones that support VPN operation.
Note: DisplayString syntax is used for IP addresses to allow the same object to be used for IPv4 and IPv6 addresses.
Object Identifier
Syntax
Definition
endptALWCLRNOTIFY
Integer
Current value of ALWCLRNOTIFY converted to integer format.
endptAUTHTYPE
Integer
Current value of NVVPNAUTHTYPE converted to integer format.
endptCFGPROF
Integer
Current value of NVVPNCFGPROF converted to integer format.
endptCOPYTOS
Integer
Current value of NVVPNCOPYTOS converted to integer format.
endptDHCPSRVR
DisplayString
Current value of DHCPSRVR.
endptDROPCLEAR
Integer
Current value of DROPCLEAR converted to integer format.
endptENCAPS
Integer
Current value of NVVPNENCAPS converted to integer format.
endptEXTDNSSRVR
DisplayString
Current value of EXTDNSSRVR.
endptEXTGIPADD
DisplayString
Current value of EXTGIPADD.
endptEXTIPADD
DisplayString
Current value of EXTIPADD.
endptEXTNETMASK
DisplayString
Current value of EXTNETMASK.
endptIKECONFIGMODE
Integer
Current value of NVIKECONFIGMODE converted to integer format.
endptIKEDH
Integer
Negotiated IKE Phase 1 DH group number.
endptIKEDHGRP
Integer
Current value of NVIKEDHGRP converted to integer format.
endptIKEID
DisplayString
Current value of NVIKEID.
endptIKEIDTYPE
Integer
Current value of NVIKEIDTYPE converted to integer format.
endptIKEOVERTCP
Integer
Current value of NVIKEOVERTCP converted to integer format.
endptIKEP1AUTH
Integer
Negotiated IKE Phase 1 authentication (hash) algorithm.
endptIKEP1AUTHALG
Integer
Current value of NVIKEP1AUTHALG converted to integer format.
endptIKEP1ENC
Integer
Negotiated IKE Phase 1 encryption algorithm.
endptIKEP1ENCALG
Integer
Current value of NVIKEP1ENCALG converted to integer format.
endptIKEP1LIFESEC
Integer32
Current value of NVIKEP1LIFESEC converted to integer format.
endptIKEP2AUTH
Integer
Negotiated IKE Phase 2 authentication algorithm.
endptIKEP2AUTHALG
Integer
Current value of NVIKEP2AUTHALG converted to integer format.
endptIKEP2ENC
Integer
Negotiated IKE Phase 2 encryption algorithm.
endptIKEP2ENCALG
Integer
Current value of NVIKEP2ENCALG converted to integer format.
endptIKEP2LIFESEC
Integer32
Current value of NVIKEP2LIFESEC converted to integer format.
endptIKESALIFEKB
Integer32
IKE SA lifetime in kilobytes.
endptIKESALIFESEC
Integer32
IKE SA lifetime in seconds
endptIKETRANSPORT
Integer
“0” if IKE is not in use, “1” if UDP is being used for IKE transport, and “2” if TCP is being used for IKE transport.
endptIKEXCHGMODE
Integer
Current value of NVIKEXCHGMODE converted to integer format.
endptIPSECSALIFEKB
Integer32
IPsec SA lifetime in kilobytes.
endptIPSECSALIFESEC
Integer32
IPsec SA lifetime in seconds
endptIPSECSUBNET
DisplayString
Current value of NVIPSECSUBNET.
endptNORTELAUTH
Integer
Current value of NORTELAUTH converted to integer format.
endptPFSDH
Integer
Negotiated IKE PFS DH group number.
endptPFSDHGRP
Integer
Current value of NVPFSDHGRP converted to integer format.
endptPSWDTYPE
Integer
Current value of NVVPNPSWDTYPE converted to integer format.
endptSGINUSE
DisplayString
IP address of the Security Gateway with which the telephone currently has a VPN tunnel established, converted to ASCII dotted-decimal format (“0.0.0.0” if the telephone does not have a VPN tunnel established), see 96x1H-IPI.4.2.200.
endptSGIP
DisplayString
Current value of NVSGIP.
endptSGVENDOR
Integer
Current value of NVVPNSVENDOR converted to integer format.
endptSGVERSION
DisplayString
Version information (if any) of the Security Gateway with which the telephone currently has a VPN tunnel established, otherwise null.
endptVPNMODE
Integer
Current value of NVVPNMODE converted to integer format.
endptVPNUSER
DisplayString
Current value of NVVPNUSER.
endptVPNUSERTYPE
Integer
Current value of NVVPNUSERTYPE converted to integer format.
endptXAUTH
Integer
Current value of NVXAUTH converted to integer format.
