Honeywell hdz series Analogue tdn indoor/Outdoor ptz camera Guide Specifications in csi format



Download 63.56 Kb.
Date05.05.2018
Size63.56 Kb.
#48026

Honeywell HDZ Series Analogue TDN Indoor/Outdoor PTZ Camera Guide Specifications in CSI Format

www.honeywell.com/security 800-16955 Rev A



SECTION 28 23 29

HDZ SERIES ANALOGUE TRUE DAY/NIGHT INDOOR/OUTDOOR HIGH SPEED PTZ CAMERA



  1. GENERAL

SECTION INCLUDES

Provide a true day/night analogue indoor/outdoor high speed PTZ dome camera with 30x or 36x zoom lens for video surveillance; including design, supply, installation and commissioning.

RELATED SECTIONS

NOTE TO SPECIFIER: Include related sections as appropriate if video surveillance system is integrated to other systems.

Section 26 05 00 – Common Work Results for Electrical, for interface and coordination with building electrical systems and distribution.

Section 28 05 13 – Conductors and Cables for Electronic Safety and Security, for cabling between system servers, panels, and remote devices.

Section 28 05 28 – Pathways for Electronic Safety and Security, for conduit and raceway requirements.

Section 28 23 00 – Video Surveillance Equipment, for interface with, and administration of video recording devices and equipment.

Section 28 23 23 – Video Surveillance Systems Infrastructure.

Section 28 23 29 – Video Surveillance Remote Devices and Sensors.

REFERENCES

Reference Standards: Provide systems that meet or exceed the requirements of the following publications and organizations as applicable to the work of this Section:

Canadian ICES-003

Canadian Standards Association (CSA)

Conformity for Europe (CE)

Federal Communications Commission (FCC)

Joint Photographic Experts Group (JPEG)

National Television Systems Committee (NTSC)

Phase Alternating Line (PAL)

Underwriters Laboratories Inc. (UL)

IP Code (Ingress Protection Rating) per IEC 60529

SYSTEM DESCRIPTION

The HDZ Series analogue indoor/outdoor PTZ dome camera shall use either:

A flexible indoor enclosure that can be mounted quickly to a flat surface with one of the mounting options, easily installed with the in-ceiling mounting bracket, wall mount or pendant mount.

A rugged, discreet, outdoor NEMA 4X and IP66-rated vandal-resistant enclosure that can be easily installed directly to a ceiling, wall or roof with either the wall, ceiling or parapet mounting accessories.

The HDZ Series analogue indoor/outdoor True Day/Night PTZ dome camera shall capture video in 650 TVL horizontal resolution for clean, sharp images at 30 frames per second (NTSC) and 25 frames per second (PAL). As a True Day/Night solution, the analogue PTZ dome camera has a low light sensitivity of 0.08 lux (color) / 0.005 lux (B/W). The camera is designed for a broad range of surveillance applications and features real-time wide dynamic range to accommodate a wide variety of surveillance environments.

SUBMITTALS

General: Submittals shall be made in accordance with the Conditions of the Contract and Submittal Procedure Section.

Manufacturer’s Product Data: Submit manufacturer’s data sheets indicating systems and components proposed for use, including instruction manuals.

Shop Drawings: Submit complete shop drawings including connection diagrams for interfacing equipment, list of connected equipment, and locations for major equipment components.

Record Drawings: During construction maintain record drawings indicating location of equipment and wiring. Submit an electronic version of record drawings not later than Substantial Completion of the project.

Operation and Maintenance Data: Submit manufacturer’s operation and maintenance data, customized to the system installed. Include system and operator manuals.

Field Tests: Submit results of field testing of every device including date, testing personnel, retesting date (if applicable), and confirmation that every device passed field testing.

Maintenance Service Agreement: Submit a sample copy of the manufacturer’s maintenance service agreement, including cost and services for a one year period for Owner’s review. Maintenance shall include, but not be limited to, labor and materials to repair the system, tests and adjustments, and regular inspections.

QUALITY ASSURANCE

Manufacturer: Minimum ten years experience in manufacturing and maintaining video surveillance systems. Manufacturer shall provide toll-free technical assistance and support available 24/7.

Manufacture Location: Provide equipment assembled in Taiwan.

Installer: Minimum two years experience installing similar systems, and acceptable to the manufacturer of the video surveillance system.

Regulatory Requirements:

Emissions: EU – EN61000-6-3; NA - FCC Part 15B, ICES-003.

Environmental Requirements (protecting the dome from direct sunlight in high temperature environments is advised):

Indoor pendant dome operating temperatures shall be between 0°C (32°F) and 50°C (122°F).

Outdoor pendant dome operating temperatures shall be between −40°C (−40°F) and 50°C (122°F).

Power Requirements:

Indoor in-ceiling and pendant dome:

Input Voltage: 24 V AC ±10%, 50/60 Hz.

Power Consumption: 20 W maximum.

Outdoor pendant and vandal-resistant rugged dome:

Input Voltage: 24 V AC ±10%, 50/60 Hz.

Power Consumption: 50 W maximum (with heater/blower).

DELIVERY, STORAGE, AND HANDLING

Deliver materials in manufacturer’s labeled packages. Store and handle in accordance with manufacturer’s requirements, in a facility with environmental conditions within recommended limits.

WARRANTY

Manufacturer’s Warranty: Submit manufacturer’s warranty of three (3) years from the manufacture date code under normal use and service for the video surveillance system.



  1. PRODUCTS

MANUFACTURER

HDZ Series Camera Manufacturer: Honeywell HDZ Series analogue true day/night indoor/outdoor PTZ dome camera, www.honeywell.com/security or www.honeywellintegrated.com.

Accepted Part Numbers:

HDZ30A – PTZ Analogue Dome, Indoor Pendant, 30x TDN NTSC, Clear Dome

HDZ36AE – PTZ Analogue Dome, Outdoor Pendant, 36x TDN NTSC, Clear Dome

HDZ30AX – PTZ Analogue Dome, Indoor Pendant, 30x TDN PAL, Clear Dome

HDZ36AEX – PTZ Analogue Dome, Outdoor Pendant, 36x TDN PAL, Clear Dome

SYSTEM COMPONENTS

Indoor/Outdoor dome housing, camera scan unit, cabling, and an OSD menu that provides complete control of the PTZ dome settings.

OPERATIONAL REQUIREMENTS

The HDZ Series analogue true day/night indoor/outdoor PTZ dome camera system shall meet or exceed the following camera specifications:

Image Sensor: 1/4-inch Sony CCD

Horizontal Resolution: 650 TVL

Optical Zoom:

HDZ30A(X): 30x

HDZ36AE(X): 36x

Focal Length:

HDZ30A(X): 3.4–102.0 mm

HDZ36AE(X): 3.4–122.4 mm

Focus Mode: Auto/Manual

Iris Control: Auto/Manual

Minimum Illumination: 0.08 lux (color) / 0.005 lux (B/W) @ F1.6 (30 IRE)

Shutter Speed: 1/1–1/10,000 seconds

White Balance: Auto/Manual

Signal-to-Noise Ratio: greater than 50 dB (AGC off)

Backlight Compensation: On/Off

AGC: Auto/Manual (Max gain limit settings for Full Auto, Shutter Priority, and Iris Priority modes)

The HDZ Series analogue PTZ camera must be available with a 650 TVL super high-resolution color/monochrome (true day/night) and wide dynamic range (WDR) advanced digital signal processing (DSP) camera and a 30X optical zoom (3.4 mm to 102.0 mm) or 36X optical zoom (3.4 mm to 122.4 mm).

The HDZ Series analogue PTZ wide dynamic range (WDR) and color/monochrome (true day/night) camera shall utilize a 1/4" Sony CCD technology with a minimum horizontal resolution of 650 TVL. The camera must provide sharp, detailed images down to 0.08 lux color, and 0.005 lux monochrome. When switching to monochrome mode, the camera must automatically remove the IR cut filter when necessary, which will increase the infrared sensitivity. When enough ambient light is available to produce an acceptable color image, the camera must automatically enable the IR cut filter. The camera must also utilize WDR technology, allowing for detail to be captured accurately even in high contrast scenes.

The HDZ Series analogue PTZ camera shall support video connection through BNC or UTP cable. An optional UTP balun is included with the unit, if UTP video connection is required.

The fully featured HDZ Series analogue PTZ camera supports the following built-in Protocols:

Maxpro Mode (default), baud rate 9600, parity even

VCL, baud rate 9600, parity none

Pelco D, baud rates 2400, 4800, or 9600, parity none

Pelco P, baud rates 2400, 4800, or 9600, parity none

The HDZ Series analogue PTZ camera shall be comprised of a high-speed pan/tilt assembly using precision stepper motors with a high-strength belt drive, resulting in quiet and accurate operation.

The HDZ Series analogue PTZ camera shall transmit images with 480K effective pixels (NTSC) or 570K effective pixels (PAL) at 30 frames per second (NTSC) and 25 frames per second (PAL).

The HDZ Series analogue PTZ camera shall include, as standard, an OSD menu that provides complete control of the PTZ dome settings. The OSD menu shall be available through a connected monitor and keyboard/controller.

The HDZ Series analogue PTZ camera shall feature OSD menus for programming dome parameters. A minimum of the following menus must be available:

Language


English

Czech


German

Spanish


French

Italian


Portuguese

Russian


Simple Chinese

Traditional Chinese

Dutch

Polish


Turkish

Japanese


Display Options

ID Display

Pan azimuth and the tilt elevation display (PT Position display)

Zoom Msg.

Title Display

Title Zone Display

Time and Date Display

Diagnostic Options

Restore Default Settings

System Reset

Camera Options

Zoom and Focus

Exposure Control

White Balance

Backlight

Flip – Mechanical/Image/Off

Image Inverse

Speed by zoom

WDR

2D NR/3D NR



Auto Calibration

Motion Detection

Function Programming

Program Alarms

Program a Mimic tour

Program a Preset position

Program a Preset tour

Program a Auto pan

Program Privacy zone

Program Home

The HDZ Series analogue PTZ camera shall include, as standard, the following PTZ features and functions:

Manual pan speeds must range from 0.5º to 200º per second, and manual tilt speeds must range from 0.5º to 84º per second.

Provides for three (3) auto focus modes: PTZ trigger focus, Zoom trigger focus, and Continuous auto focus. When the scene requires extra-fine control, the dome must allow the operator to override the auto focus settings. Auto iris with manual override must also be standard.

Sixteen (16) mimic or learned tours. The user shall perform a series of pan, tilt, zoom movements that the dome must “learn”. When the pattern is recalled, the dome automatically repeats the movements. The duration of each mimic tour can be up to one hundred (100) seconds.

Support for up to sixteen (16) programmable preset tours, each with up to thirty-two (32) preprogrammed positions. Each position can include a preset position, the speed, and the dwell time (dwell time defines the time the dome rests before going to the next preset position). The tour can be programmed to run continuously until halted by the operator.

In order to quickly identify the specific PTZ an operator is viewing, the HDZ Series analogue PTZ camera shall contain title display and ID display options to display the camera information on-screen.

Sixteen (16) programmable Dynamic Privacy Zones to block sensitive areas from viewing/recording.

Incorporates flash memory to protect the programming for the privacy zones if power is lost. The flash memory shall retain the programming for a minimum of twenty (20) years. If the privacy zones have been programmed and the unit loses power, the video will remain blank until the PTZ dome finds its index position to prevent any area behind programmed privacy zones from being visible when power is restored.

Supports auto-homing to activate a preset tour, mimic tour, or a preset position after a specified period of inactivity, programmable from one (1) to one hundred and twenty-eight (128) minutes.

Able to display the pan azimuth and the tilt elevation/declination, in degrees, on the video. Users must have the ability to turn the coordinates on or off.

Displays date and time in the video for viewing/recording. Users must have the ability to turn it on/off. The HDZ analogue PTZ Series shall allow users to enter an alphanumeric camera ID/name and insert the ID/name in to the video for viewing on a monitor (add text overlay on video). In addition, a digital zoom label shall be available on the video to display the current digital zoom magnification when zoom in/out. Users must have the ability to turn both IDs/names on or off.

The HDZ Series analogue PTZ camera must provide the option of restoring all displays, alarms, camera settings, and diagnostic settings to factory default with an OSD menu command or a camera board factory reset button.

The HDZ Series analogue PTZ camera shall include four (4) on-board alarm inputs for normally open or normally closed dry contacts. The dome shall have the ability to go to a preset position, start a preset tour, start an autopan line, or start a mimic tour when an alarm occurs. The dome must insert “A” and the alarm pin number to the video signal display for viewing on the monitor until the alarm returns to its normal state. When more than one alarm occurs, the latest alarm will be performed.

The HDZ Series analogue PTZ camera shall include two (2) on-board alarm outputs for normally open or normally closed dry contacts. The dome shall have the ability to perform the relay out signal to the alarm equipment.

The HDZ Series analogue PTZ camera shall be available in indoor configurations designed for installation of in-ceiling bracket and pendant mount configurations. The bottom domes must be designed to blend in with building aesthetics and shall be constructed of vacuum-formed, optically-graded acrylic available in smoke and clear finishes. Trim rings must be available in white finishes.

The HDZ Series analogue PTZ camera shall be available in a pendant housing specifically designed for installation in an outdoor environment, with an integral resistive type thermostat-controlled 24 V AC heater and blower to maintain a sufficient operating temperature. The pendant housing shall be IP66 rated. The bottom domes shall be designed to blend in with building aesthetics and shall be constructed of vacuum-formed, optically-graded acrylic available in smoke and clear finishes. Available mounting options shall include pendant, wall, roof, and parapet, as well as pole and corner adapters.

The HDZ Series analogue PTZ camera shall be available with Vandal Proof Acrylic/bubble for indoor or outdoor environments with tamper-resistant screws. The Acrylic/bubble shall be designed to blend in with building aesthetics and shall be constructed of optically-graded acrylic available in smoke and clear finishes. The unit shall have an Industry standard 1.5" NPT connections that shall work with all existing Honeywell PTZ mounts and brackets. The PTZ dome should be protected from direct sunlight in hot climates.

HDZ SERIES INTEGRATIONS

The following mounting options are compatible with the HDZ Series analogue PTZ camera:

HDZINBKT – In-Ceiling Bracket for HDZ Series

HDVWM1 – Indoor Only Wall Mount

HDXWM2 – Indoor and Outdoor Wall Mount

HDXSM1 – Half Swan Neck Pole Mount

HDPRM2 – Parapet and Roof Mount

HDCM1 – Ceiling Mount for Indoor Pendant (Not for outdoor use)

HDXPMA2 – Pole Mount Adapter for HDXWM2

HDXCMA1 – Corner Mount Adapter for HDXWM2

The following optional accessories are compatible with the HDZ Series analogue PTZ camera:

HDZVRSMKAC – Smoked Polycarbonate Vandal Proof Acrylic for HDZ Series

HDZVRCLRAC – Clear Polycarbonate Vandal Proof Acrylic for HDZ Series (repair purposes only)

HDZIK10AC – Clear IK10 Vandal Proof Acrylic for HDZ Series

517082-7130 – In-Ceiling PTZ Support Plate

The following recorders and devices are compatible with the HDZ Series Analogue PTZ camera:

MAXPRO® NVR Hybrid XE, SE, PE – Entry to Enterprise Level Hybrid Network Video Recorders

Fusion Hybrid DVR – Full-featured Hybrid Digital Video Recorder

HVE Encoders – Network Audio/Video Encoder

Rapid Eye – 4, 8, and 16 Channel Hybrid Digital Video Recorder

HRDP – Digital Video Recorder

HREP II – Digital Video Recorder

HVBPIT44 – Protocol Translator

HVBGPIO – Protocol Translator

MegaPIT – Protocol Interface Translator

HJC4000 – UltraKey Touch Keyboard/Controller

SYSTEM HARDWARE

The HDZ Series analogue PTZ camera shall have the following mechanical specifications:

Indoor unit using the In-Ceiling bracket:

Unit Dimensions (H x Dia.): 9.1" x 10.0" (231.5 mm x 254.0 mm)

Unit Weight: 6.83 lb (3.1 kg)

Lower Dome Diameter: 5.8" (148.0 mm)

Indoor Pendant unit:

Unit Dimensions (H x Dia.): 10.8" x 7.5" (275.1 mm x 191.5 mm)

Unit Weight: 4.85 lb (2.2 kg)

Lower Dome Diameter: 7.5" (191.5 mm)

Outdoor Pendant unit:

Unit Dimensions (H x Dia.): 10.7" x 7.5" (270.5 mm x 191.5 mm)

Unit Weight: 5.73 lb (2.6 kg)

Lower Dome Diameter: 7.5" (191.5 mm)

The HDZ Series analogue PTZ camera shall have the following electrical specifications:

Indoor In-Ceiling and Indoor Pendant dome:

Input Voltage: 24 V AC ±10%, 50/60 Hz

Power Consumption: 20 W maximum

Outdoor Pendant and Vandal-Resistant Rugged dome:

Input Voltage: 24 V AC ±10%, 50/60 Hz

Power Consumption: 50 W maximum (with heater/blower)

The HDZ Series analogue PTZ camera shall be designed to meet the following environmental conditions:

Indoor In-Ceiling and Indoor Pendant dome:

Operating Temperature: 32°F to 122°F (0°C to 50°C)

Outdoor Pendant and Vandal-Resistant Rugged dome:

Operating Temperature: –40°F to 122°F (–40°C to 50°C)

Relative Humidity: 10%-90%, non-condensing

Emissions: EU – EN61000-6-3; NA - FCC Part 15B, ICES-003

Immunity: CE - EN50130-4

Safety: EU - EN60950-1, EN60950-22
NA – UL/CSA 60950-1, UL/CSA 60950-22

MANUFACTURER SUPPORT

Manufacturer shall provide customer service, pre-sales applications assistance, after-sales technical assistance, access to online technical support, and online training using Web conferencing.

Manufacturer shall provide 24/7 technical assistance and support by means of a toll-free telephone number at no extra charge.



  1. EXECUTION

EXAMINATION

Examine site conditions prior to installation. Notify Architect and Owner in writing if unsuitable conditions are encountered. Do not start installation until site conditions are acceptable.

INSTALLATION

All components of the camera system shall be thoroughly tested before shipping to the project location.

Camera system shall be installed, programmed, and tested in accordance with manufacturer’s installation instructions.

Coordinate interfaces with Owner’s representative where appropriate.

Provide conduit, cable and wire for a complete and reliable installation. Obtain Owner’s approval for exact location of the camera and all boxes, conduit, cable, and wiring runs prior to installation.

Install conduit, cable, and wire parallel and square with building lines, including raised floors areas. Do not exceed forty percent (40%) fill in conduits. Gather wires and tie to create an orderly installation.

Coordinate with other trades to provide proper sequencing of installation.

FIELD COMMISSIONING AND CERTIFICATION

Field Commissioning: Test dome camera system as recommended by manufacturer, including the following:

Conduct complete inspection and testing of equipment, including verification of operation with connected equipment.

Test devices and demonstrate operational features for Owner’s representative and authorities having jurisdiction, as applicable.

Correct deficiencies until satisfactory results are obtained.

Submit written copies of test results.

TRAINING


Conduct on-site system administrator and security/surveillance operator training, with the number of sessions and length of sessions as recommended by the video surveillance system manufacturer. Training shall include, but not limited to camera administration, provisioning, configuration, operation, and diagnostics.

END OF SECTION



28 23 29-


Download 63.56 Kb.

Share with your friends:




The database is protected by copyright ©ininet.org 2024
send message

    Main page