Section 00000 Security Access and Surveillance honeywell video systems htcd50 and htcd52 mobile digital cameras part 1 – general

1. 
   SUMMARY
   

1. 
   The HTCD50 and HTCD52 all digital, network IP cameras shall provide video and audio in a digitized data format. The cameras shall interface with the HTRD400 Mobile Digital Recorder Unit (HTRD400) via RJ45 connector. The camera enclosures shall be high-impact and tamper resistant, designed for use in school bus and transit applications under closed-loop network conditions. The HTCD50 and HTCD52 are identical except that the HTCD50 is a single-window version and the HTCD52 is a dual-window version.
   

2. 
   REFERENCES
   

1. 
   Canadian Standards Association (CSA)
   
2. 
   Conformity for Europe (CE) [John ?]
   
3. 
   Federal Communications Commission (FCC)
   
4. 
   National Television System Committee (NTSC)
   
5. 
   Phase Alternation Line (PAL) [John ?]
   

3. 
   DEFINITIONS
   

1. 
   No Substitutes: The exact make and model number identified in this specification shall be provided without exception.
   

2. 
   Or Equal: Any item may be substituted for the specified item provided that in every technical sense, the substituted item provides the same or better capability and functionality.
   

3. 
   Or Approved Equal: A substitute for the specified item may be offered for approval by the Owner. The proposed substitution must, in every technical sense, provide the same or better capability and functionality as the specified item. Such requests for approval shall be submitted in accordance with the provisions of PART 1.05 – SUBMITTALS, and must be obtained within the time frames outlined.
   

4. 
   SYSTEM DESCRIPTION
   

1. 
   The HTCD5x camera is a fully integrated, pre-focused digital camera. The HTCD4x camera shall consist of a 1/3" monochrome/color video camera using a digital CMOS image sensor meeting NTSC (EIA) or PAL (CCIR) signal format. The resolution shall be a minimum of 640 x 480 for VGA and 320 x 240 for QVGA.
   

5. 
   SUBMITTALS
   

1. 
   General: Submittals shall be made in accordance with the Conditions of the Contract and Submittal Procedures Section.
   

2. 
   Shop Drawings and Schematics: Shall depict the HTCD5x camera in final proposed “as built” configuration. The following must be provided:
   

1. 
   Connection diagrams for interfacing equipment
   
2. 
   List of connected equipment
   
3. 
   Locations for all major equipment components to be installed under this specification
   

3. 
   Product Data: The following shall be provided:
   

1. 
   Technical data sheets
   
2. 
   A complete set of instruction manuals
   

4. 
   Quality Assurance Submittals: The following shall be submitted:
   

1. 
   Checkout Report: The Contractor shall provide the Owner with a checkout report for each HTCD5x camera. The report shall include:
   

1. 
   A complete list of every device
   
2. 
   The date it was tested, and by whom
   
3. 
   If retested, the date it was retested, and by whom
   
4. 
   The final test report shall indicate that every device was tested successfully.
   

2. 
   Manufacturer’s Instructions: The Contractor shall deliver TBD sets of System Operation and Maintenance Manuals (if available) to the Owner.
   
3. 
   Notice of Completion: When the final acceptance has been satisfactorily completed, the Owner shall issue a notice of completion to the Contractor.
   

6. 
   QUALITY ASSURANCE
   

1. 
   Manufacturer’s Qualifications: The HTCD5x camera manufacturer shall be the world’s largest and most experienced manufacturer of electronic security systems, with over seventy years of experience in the security industry. The manufacturer must be assembled in the U.S.A. and the manufacturer shall provide 24/7 technical assistance and support via a toll-free telephone number at no extra charge.
   

7. 
   DELIVERY, STORAGE, AND HANDLING
   

1. 
   General: Delivery, storage, and handling of the HTCD5x camera shall be in accordance with the manufacturer’s recommendations.
   

2. 
   Ordering: The manufacturer’s ordering instructions and lead-time requirements must be followed in order to avoid installation delays.
   

3. 
   Delivery: The HTCD5x camera shall be delivered in the manufacturer’s original, unopened, undamaged container with identification labels intact.
   

4. 
   Storage and Protection: The HTCD5x camera shall be stored and protected from exposure to harmful weather conditions and at the environmental conditions recommended by the manufacturer.
   

8. 
   PROJECT CONDITIONS
   

9. 
   SEQUENCING
   

10. 
    SCHEDULING
    

11. 
    WARRANTY
    

1. 
   General: The warranty period shall be a minimum of thirty-six (36) months from the manufacture date code under normal use and service.
   

12. 
    MAINTENANCE
    

1. 
   Preventative Maintenance Agreement During Warranty: As a separate price item, the Contractor shall provide preventative maintenance during the warranty period. Maintenance shall include, but not be limited to:
   

1. 
   Labor and materials, at no additional cost, to repair the HTCD5x camera.
   
2. 
   Labor and materials, at no additional cost, to provide test and adjustments to the HTCD5x camera.
   
3. 
   Regular inspections.
   

2. 
   Preventative Maintenance Agreement: As a separate price item, the Contractor shall provide a complete Maintenance Agreement for a period of TBD months after the conclusion of the warranty period. The Maintenance Agreement shall include, but not be limited to:
   

1. 
   Labor and materials, at no additional cost, to repair the HTCD5x camera
   
2. 
   Labor and materials, at no additional cost, to provide test and adjustments to the HTCD5x camera
   
3. 
   Regular inspections
   

13. 
    TRAINING
    

1. 
   Operator training shall be conducted for a minimum of TBD sessions, with a minimum session length of TBD hours at the customer’s site.
   

2. 
   Training shall include, but not be limited to, the HTCD5x camera operation and diagnostics.
   

1. 
   Model Number/Description Table
   

HTCD50MB036	HTCD50 SERIES: B&W,3.6MM LENS,AUDIO
HTCD50MB060	HTCD50 SERIES: B&W,6MM LENS,AUDIO
HTCD50MB080	HTCD50 SERIES: B&W,8MM LENS,AUDIO
HTCD50MB120	HTCD50 SERIES: B&W,12MM LENS,AUDIO
HTCD50MC036	HTCD50 SERIES: COLOR,3.6MM LENS,AUDIO
HTCD50MC060	HTCD50 SERIES: COLOR,6MM LENS,AUDIO
HTCD50MC080	HTCD50 SERIES:COLOR,8MM LENS,AUDIO
HTCD50MC120	HTCD50 SERIES: COLOR,12MM LENS,AUDIO
HTCD50BB036	HTCD50 SERIES: B&W,3.6MM LENS
HTCD50BB060	HTCD50 SERIES: B&W,6MM LENS
HTCD50BB080	HTCD50 SERIES: B&W,8MM LENS
HTCD50BB120	HTCD50 SERIES: B&W,12MM LENS
HTCD50BC036	HTCD50 SERIES: COLOR,3.6MM LENS
HTCD50BC060	HTCD50 SERIES: COLOR,6MM LENS
HTCD50BC080	HTCD50 SERIES: COLOR,8MM LENS
HTCD50BC120	HTCD50 SERIES: COLOR,12MM LENS
HTCD52MB036	HTCD52 SERIES: B&W,3.6MM LENS,DUAL ANGLE,AUDIO
HTCD52MB060	HTCD52 SERIES: B&W,6MM LENS,DUAL ANGLE,AUDIO
HTCD52MB080	HTCD52 SERIES: B&W,8MM LENS,DUAL ANGLE,AUDIO
HTCD52MB120	HTCD52 SERIES: B&W,12MM LENS,DUAL ANGLE,AUDIO
HTCD52MC036	HTCD52 SERIES: COLOR,3.6MM LENS,DUAL ANGLE,AUDIO
HTCD52MC060	HTCD52 SERIES: COLOR,6MM LENS,DUAL ANGLE,AUDIO
HTCD52MC080	HTCD52 SERIES: COLOR,8MM LENS,DUAL ANGLE,AUDIO
HTCD52MC120	HTCD52 SERIES: COLOR,12MM LENS,DUAL ANGLE,AUDIO
HTCD52BB036	HTCD52 SERIES: B&W,3.6MM LENS,DUAL ANGLE
HTCD52BB060	HTCD52 SERIES: B&W,6MM LENS,DUAL ANGLE
HTCD52BB080	HTCD52 SERIES: B&W,8MM LENS,DUAL ANGLE
HTCD52BB120	HTCD52 SERIES: B&W,12MM LENS,DUAL ANGLE
HTCD52BC036	HTCD52 SERIES: COLOR,3.6MM LENS,DUAL ANGLE
HTCD52BC060	HTCD52 SERIES: COLOR,6MM LENS,DUAL ANGLE
HTCD52BC080	HTCD52 SERIES: COLOR,8MM LENS,DUAL ANGLE
HTCD52BC120	HTCD52 SERIES: COLOR,12MM LENS,DUAL ANGLE
HTCD52LID	HTCD52 SERIES: DUAL WINDOW HOUSING TO CONVERT HTCD50 TO HTCD52

2. 
   SYSTEM PERFORMANCE
   

1. 
   The HTCD5x camera shall include, as a minimum, the following features/functions/specifications:
   

1. 
   The HTCD5x camera must be protected by the most extensive support services in the industry, including Customer Service, Pre-Sales Applications Assistance, After-Sales Technical Assistance, access to Technical Online Support, and Online Training using web conferencing.
   

2. 
   The HTCD5x camera and its components shall be thoroughly tested before shipping from the manufacturer’s facility.
   

3. 
   The HTCD5x camera shall incorporate a 1/3-inch digital signal processing (DSP) to provide high quality JPEG compressed video with low power requirements.
   

4. 
   The UTCD5x camera sensor and processor utilizes an effective pixel count of no less than 640 (H) x 480 (V) VGA, 320 (H) x 240 (V) QVGA and shall be capable of delivering digital pixel data at frame rates of up to 15 frames per second in VGA mode and 30 frames per second in QVGA mode.
   

5. 
   The HTCD5x camera shall support user selectable image quality and compression settings using the HTRD400 Mobile Digital Recording System Toolbox software, including:

   A minimum of four image quality settings (Extended, Good, Better, Best)

   A minimum of two image compression settings (VGA and QVGA)
   

6. 
   The HTCD5x camera shall support an internal microphone and digital audio. The bandwidth shall be optimized to eliminate unwanted noise interference
   
   
   
7. 
   The power consumption of the HTCD5x camera shall be no more than 4.0 watts.
   

8. 
   The HTCD5x camera shall have a signal to noise ratio of 45 dB with the AGC off.
   

9. 
   The HTCD5x color camera models shall incorporate auto-tracking brightness, exposure, and white balance to constantly monitor the light and adjust its color.
   

10. 
    The HTCD5x camera shall provide a standard shielded RJ45 connector to directly connect to the HTRD400 Mobile Digital Video Recorder using standard CAT5 cable. The RJ45 connector shall also accept power in for the camera at 12V @ 250 mA. Power to the camera shall be controlled by the HTRD400.
    

11. 
    The HTCD5x camera shall be fully assembled and pre-focused and shall offer flexible mounting options in a mobile environment, including on a bulkhead, wall, or ceiling.
    

12. 
    The HTCD5x camera shall provide over-current and over-temperature protection.
    
    
    

2. 
   MECHANICAL SPECIFICATIONS
   

1. 
   The HTCD5x camera must have the following mechanical specifications:
   

1. 
   HTCD50 Dimensions (H x W x D) 2.8” x 3.54” x 5.72”
   

HTCD52 Dimensions (H x W x D) 2.05” x 3.54” x 5.73”

(75 mm x 90 mm x 145.6 mm)

2. 
   HTCD50 Unit Weight 1.81 lb. (818 g)
   HTCD52 Unit Weight 1.84 lb. (836 g)
   
   
   
3. 
   Video Output JPEG
   
   
   
4. 
   Housing Material Polycarbonate (impact-resistant) cover and die cast aluminum alloy base.
   

2. 
   ELECTRICAL POWER REQUIREMENTS
   

1. 
   The HTCD5x camera must have the following electrical specifications:
   

1. Voltage 12 VDC

2. Power Consumption <4.0 watts [John ?]

2. 
   ENVIRONMENTAL CONDITIONS
   

1. 
   The HTCD5x camera shall be designed to meet the following environmental conditions:
   

1. 
   Operating Temperature 32° to 113° F (0° to 45° C)
   
2. 
   Storage Temperature -40° to 149° F (-40° to 65° C)
   
3. 
   Emissions FCC: Part 15, Class A
   

4. 
   Immunity EN61000-4-3 & EN6100-4-6 [John?]
   
5. 
   Safety EU: 73/23/EEC LVD [John ?]
   

1. 
   Submission of a proposal confirms that the contract documents and site conditions are accepted without qualifications unless exceptions are specifically noted.
   

2. 
   The site shall be visited on a regular basis to appraise ongoing progress of other trades and contractors, make allowances for all ongoing work, and coordinate the requirements of this contract in a timely manner.
   

3. 
   The HTCD5x camera must be inspected before installation, and shall be free of any cosmetic defects or damage.
   

3.02 PREPARATION

1. 
   Prior to installation, the HTCD5x camera shall be configured and tested in accordance with the manufacturer’s instructions.
   

3.03 INSTALLATION

1. 
   The HTCD5x camera must be installed, programmed, and tested in accordance with the manufacturer’s instructions.
   

1. 
   In order to ensure a complete, HTCD5x camera, for bidding purposes, where information is not available from the Owner upon request, the worst-case condition shall be assumed.
   

2. 
   Interfaces shall be coordinated with the Owner’s representative, where appropriate.
   

3. 
   All necessary connectors, supports, cable, and wire must be furnished and installed to provide a complete and reliable HTCD5x camera installation. Exact location of all connectors and wiring runs shall be presented to the Owner for approval in advance of any installation.
   

4. 
   All conduit, cable, and wire shall be installed parallel and square with building lines, including raised floor areas. Conduit fill shall not exceed forty percent (40%). All wires shall be gathered and tied up to create an orderly installation.
   

3.04 TESTING AND CERTIFICATION

1. 
   The Contractor shall demonstrate the functionality of the HTCD5x camera upon completion of installation, documenting the result of all tests and providing these results to the Owner. The HTCD5x camera shall be tested in accordance with the following:
   

1. 
   The Contractor shall conduct a complete inspection and test of all installed HTCD5x camera equipment. This includes testing and verifying operation with connected equipment.
   

2. 
   The Contractor shall provide staff to test all devices and all operational features of the system for witness by the Owner’s representative and the Authority Having jurisdiction. All testing must be witnessed by the Owner’s representative, prior to acceptance.
   

3. 
   The testing and certification shall take place as follows:
   

1. 
   The HTCD5x camera shall be tested in conjunction with the manufacturer’s representative.
   
2. 
   All deficiencies noted in the above test shall be corrected.
   
3. 
   Test results shall be submitted to the consultant or Owner’s representative.
   
4. 
   The test and correction of any deficiencies shall be witnessed by the Owner’s representative, and noted.
   
5. 
   The Owner’s representative shall accept the system.
   
6. 
   The system test shall be witnessed by the Authority Having Jurisdiction. Any deficiencies noted during the testing must be corrected.
   

4. 
   A letter of certification shall be provided to indicate that the tests have been performed, and all devices are operational.
   

END OF SECTION

Brief Specification

The HTCD50 and HTCD52 mobile digital cameras (HTCD5x) are an integral part of the Mobile Digital Recording System. The Mobile Digital Recording System, a powerful, intelligent, fully integrated, digital IP network solution that combines capabilities for Video, Audio, and Data gathering in a single mobile Digital Recorder Unit, is designed for harsh mobile environments. The Mobile Digital Recording System shall consist of the following components: Digital Recorder Unit, software for configuration (Toolbox), software to review video (Player), and up to four (4) mobile digital cameras. The Mobile Digital Recording System shall support four (4) channels of video in and four (4) simultaneous channels of synchronized audio, as provided by the HTCD5x digital cameras. The HTCD5x is an all-digital, fully assembled and pre-focused camera that provides both video and audio in a digitized data format. HTCD5x camera shall incorporate a 1/3-inch digital signal processing (DSP) to provide high quality JPEG compressed video with low power requirements. The camera sensor and processor delivers a digital pixel data frame rate of up to 15 fps in VGA mode and 30 fps in QVGA mode. The HTCD50 and HTCD52 cameras shall be available in color and monochrome models. The HTCD5x color camera models shall incorporate auto-tracking brightness, exposure, and white balance to constantly monitor the light and adjust its color. The HTCD5x shall have a signal-to-noise ratio of 45 dB with the AGC off. The HTCD5x camera shall include a standard shielded RJ45 connector to directly connect to the HTRD400 Mobile Digital Video Recorder. The RJ45 connector shall also accept power in for the camera at 12 VDC. The power consumption of the HTCD5x camera shall be no more than 4.0 watts. The HTCD5x camera shall support user selectable image quality and compression settings using the HTRD400 Mobile Digital Recording System Toolbox software. The camera shall support an internal microphone and digital audio and the bandwidth shall be optimized to maximize audio clarity. The camera shall provide over-current and over-temperature protection; the camera shall be designed to go into off mode when the temperature is out of the specified operating temperature. The camera shall recover from temporary temperature and power interruptions without damage. The mobile digital camera shall be the Honeywell Video Systems HTCD50, HTCD52, or equivalent.