Extended System Parameters Message

2.6.2.2.5 Extended System Parameters Message

If the protocol revision level supported by the mobile station (MOB_P_REV_p) is less than the minimum protocol revision level supported by the base station (MIN_P_REV_r), the mobile station shall enter the System Determination Substate of the Mobile Station Initialization State with a protocol mismatch indication (see 2.6.1.1). Otherwise, the mobile station shall store the following parameters:

• Configuration message sequence number (CONFIG_MSG_SEQ_s = CONFIG_MSG_SEQ_r, EXT_SYS_PAR_MSG_SEQ_s= CONFIG_MSG_SEQ_r)

• Preferred Access Channel MSID type (PREF_MSID_TYPE_s = PREF_MSID_TYPE_r)

• Extended Preferred Access Channel MSID type (EXT_PREF_MSID_TYPE_s = EXT_PREF_MSID_TYPE_r) if included; otherwise, set EXT_PREF_MSID_TYPE_s to NULL.

• MEID Required indicator (MEID_REQD_s = MEID_REQD_r) if included; otherwise, set MEID_REQD_s to ‘0’

• Broadcast slot cycle index (BCAST_INDEX_s = BCAST_INDEX_r)

• The mobile station shall set its operational IMSI, IMSI_O, as follows:

– If IMSI_T_SUPPORTED_r is equal to ‘0’, the mobile station shall set IMSI_O to IMSI_M_p.

– If IMSI_T_SUPPORTED_r is equal to ‘1’ and the mobile station’s IMSI_T_p has been programmed, the mobile station shall set IMSI_O to IMSI_T_p.

– If IMSI_T_SUPPORTED_r is equal to ‘1’ and the mobile station’s IMSI_T_p has not been programmed, the mobile station shall set IMSI_O to IMSI_M_p.

• If MCC_r = ‘1111111111’ and IMSI_11_12_r = ‘1111111’, the mobile station shall set the IMSI_O to IMSI_M_p and store:

– Mobile Country Code (MCC_s = MCC_M_p) and

– IMSI 11th and 12th digits (IMSI_11_12_s = IMSI_M_11_12_p);

otherwise, the mobile station shall store:

– Mobile Country Code (MCC_s = MCC_r) and

– IMSI 11th and 12th digits (IMSI_11_12_s = IMSI_11_12_r).

• Least significant digit of MNC (IMSI_10_s = IMSI_10_r), if included.

• If IMSI_O is set to the IMSI_M, the mobile station shall set:

– IMSI_O_S_s to IMSI_M_S_p (i.e., IMSI_O_S1_s to IMSI_M_S1_p and IMSI_O_S2_s to IMSI_M_S2_p)

– IMSI_O_11_12_s to IMSI_M_11_12_p

– MCC_O_s to MCC_M_p

– IMSI_O_ADDR_NUM_s to IMSI_M_ADDR_NUM_p

• If IMSI_O is set to the IMSI_T, the mobile station shall set:

– IMSI_O_S_s to IMSI_T_S_p (i.e., IMSI_O_S1_s to IMSI_T_S1_p and IMSI_O_S2_s to IMSI_T_S2_p).

– IMSI_O_11_12_s to IMSI_T_11_12_p

– MCC_O_s to MCC_T_p

– IMSI_O_ADDR_NUM_s to IMSI_T_ADDR_NUM_p

• If IMSI_O has been changed, the mobile station shall set SYS_PAR_MSG_SEQ_s, CHAN_LST_MSG_SEQ_s, EXT_CHAN_LST_MSG_SEQ_s, FD_CHAN_LST_MSG_SEQ_s to NULL, and set PAGE_CHAN_s to ‘1’, and set PAGECH_s to the Primary Paging Channel.

• Protocol revision level (P_REV_s = P_REV_r) if included in the message; otherwise, set P_REV_s as follows:

– For Band Class 0, if the mobile station determines it is operating in Korea, set P_REV_s to ‘00000010’; otherwise, set P_REV_s to ‘00000011’.

– For Band Class 3, set P_REV_s to ‘00000011’.

– For Band Class 1 and Band Class 4, set P_REV_s to ‘00000001’.

• Minimum protocol revision level (MIN_P_REV_s = MIN_P_REV_r) if included in the message; otherwise, MIN_P_REV_s = ‘00000010’ for Band Class 0, MIN_P_REV_s = ‘00000001’ for Band Class 1 and Band Class 4, and MIN_P_REV_s = ‘00000011’ for Band Class 3.

• Protocol revision level currently in use (P_REV_IN_USE_s = the lesser value of P_REV_s and MOB_P_REV_p of the current band class)

• Slope of the handoff add/drop criterion (SOFT_SLOPE_s = SOFT_SLOPE_r) if included in the message; otherwise, SOFT_SLOPE_s = ‘000000’.

• Intercept of the handoff add criterion (ADD_INTERCEPT_s = ADD_INTERCEPT_r)

• Intercept of the handoff drop criterion (DROP_INTERCEPT_s = DROP_INTERCEPT_r)

• Delete foreign TMSI (DELETE_FOR_TMSI_s = DELETE_FOR_TMSI_r)

• Use TMSI (USE_TMSI_s = USE_TMSI_r)

• TMSI zone length (TMSI_ZONE_LEN_s = TMSI_ZONE_LEN_r)

• TMSI zone number (TMSI_ZONE_s = TMSI_ZONE_r)

• Maximum number of alternative service options (MAX_NUM_ALT_SO_s = MAX_NUM_ALT_SO_r).

• System reselection indicator (RESELECT_INCLUDED_s = RESELECT_INCLUDED_r) if included in the message; otherwise, RESELECT_INCLUDED_s = ‘0’.

• Pilot reporting indicator (PILOT_REPORT_s = PILOT_REPORT_r)

• Neighbor Set access entry handoff information indicator (NGHBR_SET_ENTRY_INFO_s = NGHBR_SET_ENTRY_INFO_r) if included in the message; otherwise, NGHBR_SET_ENTRY_INFO_s = ‘0’.

• Neighbor Set access handoff information indicator (NGHBR_SET_ACCESS_INFO_s = NGHBR_SET_ACCESS_INFO_r) if included in the message; otherwise, NGHBR_SET_ACCESS_INFO_s = ‘0’.

• Short Data Burst supported indicator (SDB_SUPPORTED_s = SDB_SUPPORTED_r)

• Nominal reverse traffic channel output power offset relative to Reverse Pilot Channel power (RLGAIN_TRAFFIC_PILOT_s = RLGAIN_TRAFFIC_PILOT_r)

• Broadcast GPS Assist Indicator (BROADCAST_GPS_ASST_s = BROADCAST_GPS_ASST_r)

• Reverse Power Control Delay (REV_PWR_CNTL_DELAY_s = REV_PWR_CNTL_DELAY_r) if included

• Permission for the mobile station to request QoS settings in the Origination Message, Origination Continuation Message, or Enhanced Origination Message (MOB_QOS_s = MOB_QOS_r)

• If ENC_SUPPORTED_r is equal to ‘1’, the mobile station shall store:

– Signaling encryption supported indicator (SIG_ENCRYPT_SUP_s = SIG_ENCRYPT_SUP_r)

– User information encryption supported indicator (UI_ENCRYPT_SUP_s = UI_ENCRYPT_SUP_r)

• Sync ID supported indicator (USE_SYNC_ID_s = USE_SYNC_ID_r)

• Concurrent services supported indicator (CS_SUPPORTED_s = CS_SUPPORTED_r)

• Maximum number of additional service reference identifiers allowed in origination (MAX_ADD_SERV_INSTANCE_s = MAX_ADD_SERV_INSTANCE_r), if included; otherwise, the mobile station shall set MAX_ADD_SERV_INSTANCE_s to 0.

• Primary Broadcast Control Channel supported indicator (BCCH_SUPPORTED_s = BCCH_SUPPORTED_r).

• Pilot information request supported indicator (PILOT_INFO_REQ_SUPPORTED_s = PILOT_INFO_REQ_SUPPORTED_r).

• Message integrity supported indicator (MSG_INTEGRITY_SUP_s = MSG_INTEGRITY_SUP_r), if P_REV_IN_USE_s is greater than or equal to 10; otherwise, MSG_INTEGRITY_SUP_s = 0.

• If MSG_INTEGRITY_SUP_r is equal to ‘1’ and SIG_INTEGRITY_SUP_INCL_r is equal to ‘1’, the mobile station shall store the message integrity algorithms that the base station supports (SIG_INTEGRITY_SUP_s = SIG_INTEGRITY_SUP_r); otherwise, the mobile station shall set SIG_INTEGRITY_SUP_s to ‘00000000’.

• Band class information request indicator (BAND_CLASS_INFO_REQ_s = BAND_CLASS_INFO_REQ_r)

• Alternate CDMA band class (ALT_BAND_CLASS_s = ALT_BAND_CLASS_r), if BAND_CLASS_INFO_REQ_r is equal to ‘1’.

• CDMA off time report supported indicator (CDMA_OFF_TIME_REP_SUP_IND_s = CDMA_OFF_TIME_REP_SUP_IND_r)

• If CDMA_OFF_TIME_REP_SUP_IND_r is equal to ‘1’, the mobile station shall store:

– CDMA off time report threshold (CDMA_OFF_TIME_REP_THRESHOLD_s = CDMA_OFF_TIME_REP_THRESHOLD_r in units specified by CDMA_OFF_TIME_REP_UNIT_r)

• Control Hold Mode supported indicator (CHM_SUPPORTED_s = CHM_SUPPORTED_r) if included; otherwise, the mobile station shall perform the following:

– If P_REV_IN_USE_s is less than six, set CHM_SUPPORTED_s to ‘0’.

– Otherwise, set CHM_SUPPORTED_s to ‘1’.

• Release to Idle State allowed indicator (RELEASE_TO_IDLE_IND_s = RELEASE_TO_IDLE_IND_r).

• Reconnect Message supported indicator (RECONNECT_MSG_IND_s = RECONNECT_MSG_IND_r).

• Short Data Burst allowed in Reconnect Message allowed indicator (SDB_IN_RCNM_IND_s = SDB_IN_RCNM_IND_r), if included; otherwise, set SDB_IN_RCNM_INDs to ‘0’.

• Forward Packet Data Channel supported Indicator (FOR_PDCH_SUPPORTED_s = FOR_PDCH_SUPPORTED_r).

• PDCH Control Hold Mode supported indicator (PDCH_CHM_SUPPORTED_s = PDCH_CHM_SUPPORTED_r) if included; otherwise, set PDCH_CHM_SUPPORTED_s to ‘0’.

• If RER_MODE_SUPPORTED_r is not included, the mobile station shall set RER_MODE_SUPPORTED_s to ‘0’; otherwise, the mobile station shall set RER_MODE_SUPPORTED_s to RER_MODE_SUPPORTED_r.

• If TKZ_MODE_SUPPORTED_r is not included, the mobile station shall set TKZ_MODE_SUPPORTED_s to ‘0’; otherwise, the mobile station shall set TKZ_MODE_SUPPORTED_s to TKZ_MODE_SUPPORTED_r. If TKZ_MODE_SUPPORTED_s is equal to ‘1’, the mobile station shall store the tracking zone identifier (TKZ_ID_s = TKZ_ID_r).

• If AUTO_FCSO_ALLOWED_r is not included, the mobile station shall set AUTO_FCSO_ALLOWED_s to ‘0’; otherwise, the mobile station shall set AUTO_FCSO_ALLOWED_s to AUTO_FCSO_ALLOWED_r.

• If CAND_BAND_INFO_REQ_r is included, the mobile station shall set CAND_BAND_INFO_REQ_s to CAND_BAND_INFO_REQ_r; otherwise, the mobile station shall set CAND_BAND_INFO_REQ_s to ‘0’.

• If BYPASS_REG_IND_r is included, the mobile station shall set BYPASS_REG_IND_s to BYPASS_REG_IND_r; otherwise, the mobile station shall set BYPASS_REG_IND_s to ‘00’.

If BCCH_SUPPORTED_s equals ‘1’, the mobile station shall enter the System Determination Substate of the Mobile Station Initialization State with a new system indication.

If P_REV_IN_USE_s has been changed, the mobile station shall set ACC_MSG_SEQ_s, CURR_ACC_MSG_SEQ, SYS_PAR_MSG_SEQ_s, EXT_NGHBR_LST_MSG_SEQ_s, GEN_NGHBR_LST_MSG_SEQ_s, and GLOB_SERV_REDIR_MSG_SEQ_s to NULL.

If NGHBR_SET_ENTRY_INFO is equal to ‘1’, the mobile station shall store the access entry handoff in order and message processing operation indicator (ACC_ENT_HO_ORDER_s = ACC_ENT_HO_ORDER_r).

If the mobile station supports packet data service options, the mobile station shall store the packet data services zone identifier (PACKET_ZONE_ID_s = PACKET_ZONE_ID_r); otherwise, the mobile station shall set PACKET_ZONE_ID_s to ‘00000000’.

If the mobile station supports packet data service options and the PZ_HYST_ENABLED field is included, the mobile station shall store the packet zone hysteresis enabled indicator (PZ_HYST_ENABLED_s = PZ_HYST_ENABLED_r); otherwise, the mobile station shall set PZ_HYST_ENABLED_s to ‘1’.

If the mobile station supports packet data service options and the PZ_HYST_LIST_LEN field is included, the mobile station shall store the packet zone hysteresis list length (PZ_HYST_LIST_LEN_s = PZ_HYST_LIST_LEN_r); otherwise, the mobile station shall set PZ_HYST_LIST_LEN_s to 4.

If the mobile station supports packet data service options and the PZ_HYST_ACT_TIMER field is included, the mobile station shall store the packet zone hysteresis activation timer (PZ_HYST_ACT_TIMER_s = PZ_HYST_ACT_TIMER_r); otherwise, the mobile station shall set PZ_HYST_ACT_TIMER_s to 30 seconds.

If the mobile station supports packet data service options and the PZ_HYST_TIMER_MUL field and the PZ_HYST_TIMER_EXP field are included, the mobile station shall store the packet zone hysteresis timer (PZ_HYST_TIMER_s = PZ_HYST_TIMER_MUL_r  8 ^ PZ_HYST_TIMER_EXP_r); otherwise, the mobile station shall set PZ_HYST_TIMER_s to 60 seconds.

If RESELECT_INCLUDED_s is equal to ‘1’, the mobile station shall store:

• 
  Pilot power threshold (EC_THRESH_s = EC_THRESH_r)
  
• 
  Pilot E_c/I₀ threshold (EC_I0_THRESH_s = EC_I0_THRESH_r)
  

• Access handoff permitted indicator (ACCESS_HO_s = ACCESS_HO_r)

• Access probe handoff permitted indicator (ACCESS_PROBE_HO_s = ACCESS_PROBE_HO_r)

• If ACCESS_PROBE_HO_s is equal to ‘1’, access handoff list update permitted indicator (ACC_HO_LIST_UPD_s = ACC_HO_LIST_UPD_r)

• Maximum number of times that the mobile station is permitted to perform an access probe handoff (MAX_NUM_PROBE_HO_s = MAX_NUM_PROBE_HO_r)

• Access handoff permitted for message response indicator (ACCESS_HO_MSG_RSP_s = ACCESS_HO_MSG_RSP_r)

• Access probe handoff permitted for other messages indicator (ACC_PROBE_HO_OTHER_MSG_s = ACC_PROBE_HO_OTHER_MSG_r)

If NGHBR_SET_ENTRY_INFO_s or NGHBR_SET_ACCESS_INFO_s is equal to ‘1’, the mobile station shall store the size of the Neighbor Set (NGHBR_SET_SIZE_s = NGHBR_SET_SIZE_r).

If NGHBR_SET_ENTRY_INFO_s is equal to ‘0’, then for all NGHBR_SET_SIZE_s occurrences of ACCESS_ENTRY_HO, the mobile station shall set the ACCESS_ENTRY_HO field of NGHBR_REC[i] to ‘0’.

If NGHBR_SET_ENTRY_INFO_s is equal to ‘1’, then for all NGHBR_SET_SIZE_s occurrences of ACCESS_ENTRY_HO, the mobile station shall set the ACCESS_ENTRY_HO field of NGHBR_REC[i] to the i^th occurrence of ACCESS_ENTRY_HO_r.

If NGHBR_SET_ACCESS_INFO_s is equal to ‘0’, then for all NGHBR_SET_SIZE_s occurrences of ACCESS_HO_ALLOWED, the mobile station shall set the ACCESS_HO_ALLOWED field of NGHBR_REC[i] to ‘0’.

If NGHBR_SET_ACCESS_INFO_s is equal to ‘1’, then for all NGHBR_SET_SIZE_s occurrences of ACCESS_HO_ALLOWED, the mobile station shall set the ACCESS_HO_ALLOWED field of NGHBR_REC[i] to the i^th occurrence of ACCESS_HO_ALLOWED_r.

The mobile station shall set all bits of TMSI_CODE_s-p to ‘1’ if all of the following conditions are met:

• The bits of TMSI_CODE_s-p are not all equal to ‘1’,

• DELETE_FOR_TMSI_s is equal to ‘1’, and

• ASSIGNING_TMSI_ZONE_LEN_s-p is not equal to TMSI_ZONE_LEN_s, or the least significant ASSIGNING_TMSI_ZONE_LEN_s-p octets of ASSIGNING_TMSI_ZONE_s-p are not equal to TMSI_ZONE_s.

If the mobile station supports the Quick Paging Channel operation:

• The mobile station shall set QPCH_SUPPORTED_s to QPCH_SUPPORTED_r.

• If QPCH_SUPPORTED_r = ‘1’:

– The mobile station shall set QPCH_RATE_s to QPCH_RATE_r.

– If the number of Quick Paging Channels specified in the received message (NUM_QPCH_r) is different from NUM_QPCH_s, the mobile station shall use the hash algorithm specified in 2.6.7.1 to select a new Quick Paging Channel number in the range 1 to NUM_QPCH_r. The mobile station shall store the new Quick Paging Channel number as QPAGECH_s and as ASSIGNED_QPAGECH_s. The mobile station shall then set NUM_QPCH_s to NUM_QPCH_r.

– The mobile station shall set QPCH_POWER_LEVEL_PAGE_s to QPCH_POWER_LEVEL_PAGE_r.

– The mobile station shall set QPCH_CCI_SUPPORTED_s to QPCH_CCI_SUPPORTED_r.

– If QPCH_CCI_SUPPORTED_r = ‘1’, the mobile station shall set QPCH_POWER_LEVEL_CONFIG_s to QPCH_POWER_LEVEL_CONFIG_r.

• The mobile station shall set QPCH_BI_SUPPORTED_s to QPCH_BI_SUPPORTED_r, if included.

• If QPCH_BI_SUPPORTED_r = ‘1’, the mobile station shall set QPCH_POWER_LEVEL_BCAST_s to QPCH_POWER_LEVEL_BCAST_r.

If the mobile station supports the Device Information Message on the r-csch, the mobile station shall store:

• Autonomous message supported indicator

If AUTO_MSG_SUPPORTED_r is equal to ‘1’ and the mobile station supports the Device Information Message on the r-csch, the mobile station shall store:

• Autonomous message interval
(AUTO_MSG_INTERVAL_s = AUTO_MSG_INTERVAL_r)

The mobile station shall store mobile station initiated position location determination supported indicator (MS_INIT_POS_LOC_SUP_IND_s = MS_INIT_POS_LOC_SUP_IND_r).

The mobile station shall set FOR_PDCH_COMMON_PARMS_s = ‘0’.

If both FOR_PDCH_SUPPORTED_r and PDCH_PARMS_INCL_r are included and equal to ‘1’, the mobile station shall perform the following:

• If FOR_PDCH_RLGAIN_INCL_r is included and equal to ‘1’, the mobile station shall set:

– (RLGAIN_ACKCH_PILOT_s = RLGAIN_ACKCH_PILOT_r).

– (RLGAIN_CQICH_PILOT_s = RLGAIN_CQICH_PILOT_r).

• The mobile station shall set

• The mobile station shall set

• The mobile station shall set NUM_SOFT_SWITCHING_SLOTS_s according to Table 3.7.2.3.2.21-9 based on the value of NUM_SOFT_SWITCHING_SLOTS_r.

• The mobile station shall set NUM_SOFTER_SWITCHING_SLOTS_s according to Table 3.7.2.3.2.21-9 based on the value of NUM_SOFTER_SWITCHING_SLOTS_r.

• The mobile station shall set PDCH_SOFT_SWITCHING_DELAY_s to PDCH_SOFT_SWITCHING_DELAY_r + 1, and PDCH_SOFTER_SWITCHING_DELAY_s to PDCH_SOFTER_SWITCHING_DELAY_r + 1.

• The mobile station shall set FOR_PDCH_COMMON_PARMS_s = ‘1’.

• The mobile station shall set WALSH_TABLE_ID_s = WALSH_TABLE_ID_r.

• The mobile station shall set NUM_PDCCH_s = NUM_PDCCH_r.

• The mobile station shall store FOR_PDCCH_WALSH_s[i] to the i^th occurrence of FOR_PDCCH_WALSH_r.

If FOR_PDCH_SUPPORTED_r is included and equal to ‘1’, then the mobile station shall set Reverse Packet Data Channel supported indicator (REV_PDCH_SUPPORTED_s = REV_PDCH_SUPPORTED_r).

If REV_PDCH_PARMS_INCL_r is not included, or if it is included and equal to ‘0’, the mobile station shall set REV_PDCH_PARMS_INCL_s to ‘0’; otherwise, the mobile station shall set REV_PDCH_PARMS_INCL_s to ‘1’ and perform the following:

• If REV_PDCH_RLGAIN_INCL_r is equal to ‘1’, the mobile station shall set:

– (RLGAIN_SPICH_PILOT_s = RLGAIN_SPICH_PILOT_r).

– (RLGAIN_REQCH_PILOT_s = RLGAIN_REQCH_PILOT_r).

– (RLGAIN_PDCCH_PILOT_s = RLGAIN_PDCCH_PILOT_r).

• If REV_PDCH_PARMS_1_INCL_r is equal to ‘1’, the mobile station shall set:

– (REV_PDCH_TABLE_SEL_s = REV_PDCH_TABLE_SEL_r).

– (REV_PDCH_MAX_AUTO_TPR_s to REV_PDCH_MAX_AUTO_TPR_r).

– (REV_PDCH_NUM_ARQ_ROUNDS_NORMAL_s = REV_PDCH_NUM_ARQ_ROUNDS_NORMAL_r+1).

• If REV_PDCH_OPER_PARMS_INCL_r is equal to ‘1’, the mobile station shall set:

– (REV_PDCH_MAX_SIZE_ALLOWED_ENCODER_PACKET_s =REV_PDCH_MAX_SIZE_ALLOWED_ENCODER_PACKET_r+1).  

– (REV_PDCH_DEFAULT_PERSISTENCE_s = REV_PDCH_DEFAULT_PERSISTENCE_r).

– (REV_PDCH_RESET_PERSISTENCE_s = REV_PDCH_RESET_PERSISTENCE_r).

– (REV_PDCH_GRANT_PRECEDENCE_s = REV_PDCH_GRANT_PRECEDENCE_r).

– (REV_PDCH_MSIB_SUPPORTED_s = REV_PDCH_MSIB_SUPPORTED_r).  

– (REV_PDCH_SOFT_SWITCHING_RESET_IND_s = REV_PDCH_SOFT_SWITCHING_RESET_IND_r).

The mobile station shall store the following parameters:

• BCMC Service Parameters Message sent
(SENDING_BSPM_s = SENDING_BSPM_r), if included; otherwise, set SENDING_BSPM_s to ‘0’.

• BCMC Service Parameters Message transmission periodicity index

• If BSPM_PERIOD_INDEX_s is not equal to NULL, the mobile station shall set BSPM_WAIT_TIME to (B + 1)160ms, where

B = 2ⁱ  16, 0 £ i £ 15

and i = BSPM_PERIOD_INDEX_s.

If CAND_BAND_INFO_REQ_r is set to ‘1’, the mobile station shall store the number of candidate band classes minus one (NUM_CAND_BAND_CLASS_s = NUM_CAND_BAND_CLASS_r).

If CAND_BAND_INFO_REQ_r is set to ‘1’, the mobile station shall perform the following for each occurrence of the CAND_BAND_CLASS record:

• 
  Set the CAND_BAND_CLASS field of CAND_BAND_CLASS_REC[i] to the i^th occurrence of CAND_BAND_CLASS_r.
  
• 
  Set the SUBCLASS_INFO_INCL field of CAND_BAND_CLASS_REC[i] to the i^th occurrence of SUBCLASS_INFO_INCL_r.
  
• 
  If the i^th occurrence of SUBCLASS_INFO_INCL_r is set to ‘1’, set the SUBCLASS_REC_LEN field of CAND_BAND_CLASS_REC[i] to the i^th occurrence of SUBCLASS_REC_LEN_r.
  
• 
  If the i^th occurrence of SUBCLASS_INFO_INCL_r is set to ‘1’, the mobile station shall perform the following for each band subclass indicator received:
  

• 
  Set the BAND_SUBCLASS_IND_REC[j] field of CAND_BAND_CLASS_REC[i] to the j^th occurrence of BAND_SUBCLASS_IND_r.