Chapter General §101. Definitions [formerly paragraph 1: 001]



Download 6.21 Mb.
Page66/89
Date29.01.2017
Size6.21 Mb.
1   ...   62   63   64   65   66   67   68   69   ...   89

AUTHORITY NOTE: Promulgated in accordance with R.S. 40:4(A)(7) and R.S. 40:5(2)(3)(7)(9)(16)(17)(20).

HISTORICAL NOTE: Promulgated by the Department of Health and Hospitals, Office of Public Health, LR 38:2885 (November 2012).

§1309. Medical Gas and Medical Vacuum Systems

A. Where medical gas and medical vacuum systems are installed, the gas piping, outlets, manifold rooms and storage rooms shall be installed in accordance with all of the requirements of the NFPA 99 by individuals properly licensed by the State Plumbing Board of Louisiana (see LAC 46:LV).

AUTHORITY NOTE: Promulgated in accordance with R.S. 40:4(A)(7) and R.S. 40:5(2)(3)(7)(9)(16)(17)(20).

HISTORICAL NOTE: Promulgated by the Department of Health and Hospitals, Office of Public Health, LR 38:2886 (November 2012).

Chapter 14. Reference Standards

§1401. Scope

A. This Chapter contains the designations, names and edition of standards referenced in this code listed alpha-numerically and the Section numbers where they are referenced.

AUTHORITY NOTE: Promulgated in accordance with R.S. 40:4(A)(7) and R.S. 40:5(2)(3)(7)(9)(16)(17)(20).

HISTORICAL NOTE: Promulgated by the Department of Health and Hospitals, Office of Public Health, LR 38:2886 (November 2012).

§1403. Referenced Standards

A. Products manufactured to those standards which are followed by the word "Listed" are required to be listed regardless of the standards' requirements for listing.



Standard Designation

Section/Table

ANSI A21.4-2008*, Cement-Mortar Lining for Ductile-Iron Pipe and Fittings for Water (same as AWWA C104)

Table 303

ANSI A21.10-2008 (R2012)*, Ductile-Iron and Gray-Iron Fittings (same as AWWA C110)

Table 603

ANSI A21.11-2006*, Rubber Gasket Joints for Ductile-Iron Pressure Pipe and Fittings (same as AWWA C111)

709.G

ANSI A21.51-2009*, Ductile-Iron Pipe, Centrifugally Cast (same as AWWA C151)

Table 603

ANSI A21.53 -2006*, Ductile-Iron Compact Fittings for Water Service (same as AWWA C153)


Table 603

ANSI A117.1-2003*, Standard for Accessible and Usable Buildings and Facilities

415.I.1, 415.I.3

ANSI A118.10-2008, Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation

Table 303, 303.G.7.c

ANSI B16.32-1992, Cast Copper Alloy Solder Joint Fittings for Sovent Drainage Systems

Table 703

ANSI B16.43-1982, Wrought Copper and Copper Alloy Solder Joint Fittings for Sovent Drainage Systems

Table 703

ANSI B31.1-55, Code for Pressure Piping

621.D

ANSI Z4.1-1986 (R2005)*, Sanitation in Places of Employment, Minimum Requirement for

405.C, Table 411 - Footnote 13

ANSI Z21.10.1-2009, Gas Water Heaters, Volume 1, Storage Water Heaters with Input Ratings of 75,000 Btu per Hour or Less (same as CSA 4.1)

503.B

ANSI Z21.10.3-2011, Gas Water Heaters Volume III, Storage, with Input Ratings Above 75,000 Btu per Hour, circulating and instantaneous (same as CSA 4.3)

503.B

ANSI Z21.22-1999(R2008)*, Relief Valves for Hot Water Supply Systems (same as CSA 4.4M)

501.F.1, 511.A.2, 511.G

ANSI Z124.1.2-2005*, Plastic Bathtub and Shower Units

Table 407, Table 415.I

ANSI Z124.3-2005*, Plastic Lavatories

Table 407

ANSI Z124.4-2006*, Plastic Water Closet Bowls and Tanks

Table 407

ANSI Z535.1-2006 (R2011), American National Standard for Safety Colors

607.A

APSP 2-1999*, Public Spas

Table 415.K

APSP 3-1999*, Permanently Installed Residential Spas

Table 415.K

APSP 6-1999*, Residential Portable Spas

Table 415.K

APSP 16-2011*, Standard Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs (same as ASME A112.19.8)

415.K.2, 415.O.6

ARI 1010-2002, Drinking Fountains and Self-Contained, Mechanically-Refrigerated Drinking-Water Coolers

415.C.1

ASME Boiler and Pressure Vessel Code, Section IX, Welding and Brazing Qualifications, 1998 Edition

315.D

ASME A13.1-2007*, Scheme for the Identification of Piping Systems

607.A.1, 607.A.3, 607.B

ASME A112.1.2-2004*, Air Gaps in Plumbing Systems

415.C.1, 415.C.2, 609.A.1, Table 609, 609.C.7, 609.F.2

ASME A112.3.1-2007*, Stainless Steel Drainage Systems for Sanitary DWV, Storm, and Vacuum Applications, Above- and Below Ground

703.C.1, 703.D, Table 703

ASME A112.3.4-2000*, Macerating Toilet Systems and Related Components

Table 407, 729.C

ASME A112.4.1-2009, Water Heater Relief Valve Drain Tubes

Table 511

ASME A112.6.1M-1997 (R2002)*, Supports for Off-the-Floor Plumbing Fixtures for Public Use (Floor -Affixed)

Table 303

ASME A112.6.2-2000*, Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks

Table 303

ASME A112.6.3-2001*, Floor Drains

Table 303

ASME A112.6.4-2003 (R2008)*, Roof, Deck, and Balcony Drains (dual roof drain assemblies wherein the inlets of both are enclosed in the same strainer are prohibited)

Table 303

ASME A112.14.1-2003 (R2008)*, Backwater Valves

705.G.2

ASME A112.14.3-2000 (R2004)*, Grease Interceptors

1005.N.1, 1005.N.5.a, 1005.N.6.a

ASME A112.18.1-2005*, Plumbing Fixture Fittings (same as CSA B125.1)

Table 407

ASME A112.18.2-2011, Plumbing Waste Fittings (Same as CSA B125.2

Table 407

ASME A112.18.3-2002*, Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

Table 407, 609.C.7

ASME A112.18.6-2009, Flexible Water Connectors (same as CSA B125.6)

Table 407, 509.B

ASME A112.19.1-2008*, Enameled Cast Iron and Enameled Steel Plumbing Fixtures (same as CSA B45.2)

Table 407, 415.C.1

ASME A112.19.2-2008*, Ceramic Plumbing Fixtures (same as CSA B45.1)

Table 407, 415.C.1

ASME A112.19.3-2008*, Stainless Steel Plumbing Fixtures (same as CSA B45.4)

Table 407

ASME A112.19.4M-1994 (R2008)*, Porcelain Enameled Formed Plumbing Fixtures

Table 407

ASME A112.19.5-2011, Trim for Water-Closet Bowls, Tanks and Urinals (same as CSA B45.15)

Table 407

ASME A112.19.6-1995*, Hydraulic Performance Requirements for Water Closets & Urinals

Table 407

ASME A112.19.7-2012, Hydromassage Bathtub Systems (same as CSA B45.10)

415.O.4, 415.O.5

ASME A112.19.8-2007*, Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs (same as APSP 16)

415.K.2, 415.O.6

ASME A112.19.9M-1991 (R2002)*, Non-vitreous Ceramic Plumbing Fixtures

Table 407

ASME A112.19.19-2006, Vitreous China Nonwater Urinals

Table 407

ASME A112.36.2M-1991 (R2002)*, Cleanouts

Table 303

ASME B1.20.1-1983 (R2006)*, Pipe Threads, General Purpose (Inch)

313.B

ASME B16.3-2011, Malleable Iron Threaded Fittings, Classes 150 and 300

Table 603

ASME B16.4-2011, Gray Iron Threaded Fittings, Classes 125 and 250

Table 603

ASME B16.5-2009, Pipe Flanges and Flanged Fittings

Table 603

ASME B16.12-2009, Cast-Iron Threaded Drainage Fittings

Table 703

ASME B16.15-2011, Cast Bronze Threaded Fittings, Classes 125 and 250

Table 603

ASME B16.18-2001, Cast Copper Alloy Solder Joint Pressure Fittings

Table 603

ASME B16.22-2001*, Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

Table 603

ASME B16.23-2011, Cast Copper Alloy Solder Joint Drainage Fittings-DWV

Table 703

ASME B16.24-2011, Cast Copper Alloy Pipe Flanges: Class 150. 300, 400, 600, 900, 1500, and 2500

Table 603

ASME B16.26-2006*, Cast Copper Alloy Fittings for Flared Copper Tubes

Table 603

ASME B 16.29-2007*, Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings-DWV

Table 703

ASME B16.34-2009, Valves-Flanged Threaded, and Welding End

Table 603

ASME B16.45-1998 (R2006)*, Cast Iron Fittings for Sovent Drainage Systems

1811.E.3

ASSE 1001-2008*, Performance Requirements for Atmospheric-Type Vacuum Breakers

Table 609

ASSE 1002-2008*, Anti-Siphon Fill Valves for Water Closet Tanks

Table 609

ASSE 1003-2009*, Performance Requirements for Water Pressure Reducing Valves for Domestic Water Distribution Systems

611.J.1, 611.J.6

ASSE 1010-2004*, Performance Requirements for Water Hammer Arresters

Table 407, 611.I.1

ASSE 1011-2004*, Performance Requirements for Hose Connection Vacuum Breakers

Table 609

ASSE 1012-2009*, Performance Requirements for Backflow Preventers with Intermediate Atmospheric Vent

Table 609, 609.C.5

ASSE 1013-2011*, Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers

Table 609, 609.C.5

ASSE 1014-2005, Performance Requirements for Backflow Prevention Devices for Hand Held Showers

Table 303

ASSE 1015-2011*, Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

Table 609

ASSE 1016-2011*, Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

Table 623, 623.A.1, 623.A.2

ASSE 1017-2009*, Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems

623.A, Table 623

ASSE 1018-2001*, Performance Requirements for Trap Seal Primer Valves - Potable Water Supplied

415.E.4.a, 625.D.1

ASSE 1019-2011*, Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining

Table 303, Table 609

ASSE 1020-2004*, Pressure Vacuum Breaker Assembly

Table 609

ASSE 1022-2003*, Backflow Preventers for Beverage Dispensing Equipment

Table 609

ASSE 1035-2008*, Performance Requirements for Laboratory Faucet Backflow Preventers

Table 303, Table 609

ASSE 1037-1990, Performance Requirements for Pressurized Flushing Devices (Flushometers) for Plumbing Fixtures

Table 303

ASSE 1043-1992, Performance Standard for Cast Iron Sovent Sanitary Drainage Systems

1811.E.3

ASSE 1044-2001*, Performance Requirements for Trap Seal Primer Devices, Drainage Types and Electronic Types

415.E.4

ASSE 1047-2011*, Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies

Table 609

ASSE 1048-2011*, Performance Requirements for Double Check Detector Fire Protection Backflow Prevention Assemblies

Table 609

ASSE 1052-2004*, Performance Requirements for Hose Connection Backflow Preventers

Table 609

ASSE 1056-2001*, Performance Requirements for Spill Resistant Vacuum Breakers

Table 609

ASSE 1061-2011*, Performance Requirements for Push-Fit Fittings (for use on PEX tubing complying with ASTM F 876 or F877, type K and L hard drawn and annealed copper tubing complying with ASTM B 88, and CPVC tubing complying with ASTM D 2846)

Table 603

ASSE 1069-2005*, Performance Requirements for Automatic Temperature Control Mixing Valves

Table 623, 623.A.1

ASSE 1070-2004*, Performance Requirements for Water Temperature Limiting Devices

Table 623, 623.B, 623.C

ASSE 1072-2007, Performance Requirements for Barrier Type Floor Drain Trap Seal Protection Devices

415.E.4

ASSE Series 5000-2009*, Cross-Connection Control Professional Qualifications Standard

319.F, Table 609, 609.F

ASSE 5110-2009, Backflow Prevention Assembly Tester Professional Qualifications Standard (part of ASSE Series 5000, Cross-Connection Control Professional Qualifications Standard)

609.F.9

ASSE 5120-2009, Backflow Prevention Assembly Surveyor Professional Qualifications Standard (part of ASSE Series 5000, Cross-Connection Control Professional Qualifications Standard)

607.C

ASSE 5130-2009, Backflow Prevention Assembly Repairer (part of ASSE Series 5000, Cross-Connection Control Professional Qualifications Standard)

609.F.9

ASTM A48/A48M-2003 (R2008), Standard Specification for Gray Iron Castings

Table 703, 717.G

ASTM A53/A53M-2012, Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless

Table 603

ASTM A74-2009, Standard Specification for Cast Iron Soil Pipe and Fittings

303.G.6.a, Table 703

ASTM A126-2004 (R2009), Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings

Table 603, Table 619.D

ASTM A197/A197M-2000 (R2011), Standard Specification for Cupola Malleable Iron

Table 603

ASTM A2692010, Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service

Table 603

ASTM A312/A312M-2012, Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes


Table 603

ASTM A377-2003 (R2008)e1, Standard Index of Specifications for Ductile-Iron Pressure Pipe

Table 603

ASTM A518/A518M-1999 (R2008), Standard Specification for Corrosion-Resistant High-Silicon Iron Castings


Table 703, 703.F

ASTM A653/ A653M-2011, Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

Table 303

ASTM A733-2003 (R2009)e1, Standard Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples


Table 603

ASTM A746-2009, Standard Specification for Ductile Iron Gravity Sewer Pipe

Table 703

ASTM A778-2001 (R2009)e1, Standard Specification for Welded, Unannealed Austenitic Stainless Steel Tubular Products


Table 603

ASTM A865/A865M-2006, Standard Specification for Threaded Couplings, Steel, Black and Zinc-Coated (Galvanized) Welded and Seamless, for Use in Steel Pipe Joints

Table 603

ASTM A888-2011, Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

Table 703

ASTM B32-2008, Standard Specification for Solder Metal

Table 303

ASTM B42-2010, Standard Specification for Seamless Copper Pipe, Standard Sizes

Table 603

ASTM B43-2009, Standard Specification for Seamless Red Brass Pipe, Standard Sizes

Table 603

ASTM B75/B75M-2011, Standard Specification for Seamless Copper Tube

Table 603

ASTM B88-2009, Standard Specification for Seamless Copper Water Tube

513.F.1, Table 603, 613.A.1, 619.A.2, 619.B

ASTM B135-2008a, Standard Specification for Seamless Brass Tube

Table 603

ASTM B135-2010, Standard Specification for Seamless Brass Tube

Table 603

ASTM B152/B152M-2009, Standard Specification for Copper Sheet, Strip, Plate and Rolled Bar

Table 303

ASTM B248-2007, Standard Specification for General Requirements for Wrought Copper and Copper- Alloy Plate, Sheet, Strip, and Rolled Bar

Table 303

ASTM B248M-2007, Standard Specification for General Requirements for Wrought Copper and Copper- Alloy Plate, Sheet, Strip, and Rolled Bar Metric

Table 303

ASTM B251-2010, Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube

Table 603

ASTM B251M-2010, Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube Metric

Table 603

ASTM B302-2007, Standard Specification for Threadless Copper Pipe, Standard Sizes

Table 603

ASTM B306-2009, Standard Specification for Copper Drainage Tube (DWV)

Table 703


Download 6.21 Mb.

Share with your friends:
1   ...   62   63   64   65   66   67   68   69   ...   89




The database is protected by copyright ©ininet.org 2020
send message

    Main page