Request for Proposal [insert date]



Download 1.62 Mb.
Page33/61
Date17.10.2016
Size1.62 Mb.
#310
TypeRequest
1   ...   29   30   31   32   33   34   35   36   ...   61

Driver Foot Controls


Accelerator and brake pedals shall be designed for ankle motion. Foot surfaces of the pedals shall be faced with wear-resistant, nonskid, replaceable material.

TS 1.1.33Pedal Angle


The vertical angle of the accelerator and brake pedals shall be determined from a horizontal plane regardless of the slope of the cab floor. The accelerator and brake pedals shall be positioned at an angle of 37 to 50 degrees at the point of initiation of contact and extend downward to an angle of 10 to 18 degrees at full throttle.

The location of the brake and accelerator pedals shall be determined by the manufacturer, based on space needs, visibility, lower edge of windshield, and vertical H-point.


TS 1.1.34Pedal Dimensions and Position


The floor-mounted accelerator pedal shall be 10 to 12 in. long and 3 to 4 in. wide. Clearance around the pedal must allow for no interference precluding operation.

Default


1 to 2 in. Between Brake and Accelerator Pedals

The accelerator and brake pedals shall be positioned such that the spacing between them, measured at the heel of the pedals, is between 1 and 2 in. Both pedals should be located approximately on the same plane coincident to the surface of the pedals.


Brake and Accelerator Pedals


Default

Brake Pedal

Non-adjustable brake pedal.
Alternative

Adjustable Brake and Accelerator Pedals

Both pedals shall be adjustable forward and rearward a minimum of 3 in. The adjustment shall be made by use of a dash-mounted toggle or rocker switch. The switch shall be clearly labeled to identify it as pedal adjustment and shall be within easy reach of the driver. Pedal adjustment shall be enabled only when the bus is stationary and the parking brake engaged.

Driver Foot Switches


Floor-Mounted Foot Control Platform

The angle of the turn signal platform shall be determined from a horizontal plane, regardless of the slope of the cab floor. The turn signal platform shall be angled at a minimum of 10 degrees and a maximum of 37 degrees. It shall be located no closer to the seat front than the heel point of the accelerator pedal.

Turn Signal Controls

Turn signal controls shall be floor-mounted, foot-controlled, water-resistant, heavy-duty, momentary contact switches.

Alternative

Adjustable turn signal platform.


Default

Foot Switch Control

The control switches for the turn signals shall be mounted on an inclined, floor-mounted stainless steel enclosure or metal plate mounted to an incline integrated into the driver’s platform, located to the left of the steering column. The location and design of this enclosure shall be such that foot room for the operator is not impeded. The inclined mounting surface shall be skid-resistant. All other signals, including high beam and public address system shall be in approved location.

The foot switches shall be UL-listed, heavy-duty type, of a rugged, corrosion-resistant metal construction. The foot switches for the directionals shall be momentary type, while those for the PA system and the high beam shall be latching type. The spacing of the switches shall be such that inadvertent simultaneous deflection of switches is prevented.

ALTERNATIVE

Other Floor-Mounted Controls

The following may be floor mounted, momentary or latching, as identified by the Agency.

• hazard


• silent alarm

• PA system


Alternative

    Steering wheel mounted (self-canceling)

Driver’s Amenities

Coat Hanger


Default

Coat Hanger

A suitable hanger shall be installed in a convenient, approved location for the driver’s coat.
Alternative

Coat Hook

A hook and loop shall be provided to secure the driver’s coat.

Drink Holder


Default

No drink holder.


Alternative

Drink Holder

A device shall be provided to securely hold the driver’s drink container, which may vary widely in diameter. It must be mounted within easy reach of the driver and must have sufficient vertical clearance for easy removal of the container. When the container is in the device, the driver’s view of the road must not be obstructed, and leakage from the container must not fall on any switches, gauges or controls.

Storage Box


Default

Storage Box

An enclosed driver storage area shall be provided with a positive latching door and/or lock. The minimum size is 2750 cubic in.
Alternative

No storage box.


Windshield Wipers and Washers

Windshield Wipers


The bus shall be equipped with a windshield wiper for each half of the windshield. At 60 mph, no more than 10 percent of the wiped area shall be lost due to windshield wiper lift. For two- piece windshields, both wipers shall park along the center edges of the windshield glass. For single-piece windshields, wipers shall park along the bottom edge of the windshield. Windshield wiper motors and mechanisms shall be easily accessible for repairs or service. The fastener that secures the wiper arm to the drive mechanism shall be corrosion-resistant.

Default


Single-control, electric two-speed intermittent wiper.
Alternative

Wiper Powered by Compressed Air

If powered by air, exhaust from the wiper motors shall be muffled or piped under the floor of the bus.
Default

Single control for air-operated system.


Alternative

Dual controls for air-operated system.


Alternative

Intermittent Wiper with Variable Control

A variable-speed feature shall be provided to allow adjustment of wiper speed for each side of the windshield between approximately five (5) and twenty-five (25) cycles per minute.
Alternative

Multiple wiper systems and controls.


Alternative

Non-Synchronized Wipers

For non-synchronized wipers, separate controls for each side shall be supplied.



Download 1.62 Mb.

Share with your friends:
1   ...   29   30   31   32   33   34   35   36   ...   61




The database is protected by copyright ©ininet.org 2024
send message

    Main page