Scope of services tubing conveyed perforating equipment and services

1. Introduction

   1. Project Overview

Operator’s East Coast operations are managed from the local office and are supported using the established logistics infrastructure and resources in St John's, Newfoundland and Labrador.

The transport of personnel to and from St. John's and the Operating Area is conducted mainly through helicopter but, in isolated situations, supply boats may be used. The Operating Area, as defined in the Agreement, covers all of the Operator's land holdings off the East Coast of Canada.

Consistent with the legislative requirements of the Canada Newfoundland Atlantic Accord Implementation Acts, the Operator is committed to enhancing the business opportunities for Canada and Newfoundland and Labrador. Consequently, Contractor is encouraged to utilize the services of Newfoundland and Labrador and other Canadian companies and personnel wherever possible.

2. Project Objectives

• 
  Execute a cost-effective program, while maintaining health, safety, quality and environmental responsibilities and meeting all due diligence requirements.
  
• 
  Minimize and phase capital expenditure.
  
• 
  Establish and maintain cost-effective relationships with suppliers and contractors, creating long term mutual benefits and a local infrastructure.
  
• 
  Effectively conduct core business activities.
  
• 
  Optimize synergy opportunities with other operators in the area.
  
• 
  Conduct operations with a moderate, cost effective, risk profile.
  
• 
  Develop synergies within product lines for completion services.
  

3. Lead Service Supplier

4. Technical Risk and Program Time

2. General Conditions

• 
  All services shall be undertaken using current best practices and in compliance with any specifications or recommendations outlined in this document or subsequent attachments hereafter. These activities shall be carried out in accordance with the Canada Newfoundland & Labrador Offshore Petroleum Board (CNLOPB) regulations.
  
• 
  Contractor must be demonstrably competent, independent, and adhere to the Contractor HSEQ (Health, Safety, Environmental and Quality) Requirements.
  
• 
  Contractor shall work strictly in accordance with and at all times comply with all relevant provincial and federal regulations, codes and standards and authorities appropriate to the Scope of Services, the subject of this Agreement.
  
• 
  The Contractor shall make the equipment and facilities to be allocated to this Agreement available for safety and operability inspection, and integration testing by the Operator or an Operator appointed representative at any time prior to termination of the contract.
  
• 
  The contractor shall provide replacement equipment as required if contracted equipment is not readily available for operations due to maintenance or any other reason not outside of operator’s control excluding redress or damage during transit to operating area.
  
• 
  Contractor shall be responsible to make themself fully aware of the Drilling Unit and local operating conditions and to specify any operational limits deemed necessary.
  
• 
  Contractor shall ensure that all Contractor’s equipment shall, on delivery, be accompanied by all appropriate current certification and maintenance records.
  
• 
  Contractor shall maintain a sufficient inventory of spares and consumables on board the Drilling Unit to ensure continued operation of all systems and ancillary equipment for seven days.
  
• 
  Contractor shall maintain locally 100 % back up of critical items for the well being completed and allow for sufficient operating spares and consumables as required to provide continuous operations.
  

• 
  Contractor shall store, preserve and maintain the materials and equipment until such time as they are mobilized.
  
• 
  Contractor shall be responsible for the assembly, testing and installation of Contractor’s equipment and materials at the work site.
  

• 
  The Operator shall notify the Contractor in writing in advance of the expected mobilization date.
  

• 
  Equipment is to be ready for mobilization to the rig for 1-May-2017. All equipment maintenance, assembly, testing and certification is the contractor’s responsibility and must be complete prior to mobilization.
  

• 
  Because of logistical and timing constraints of supplying items outside of the operating area preference will be given to optional or contingent equipment and supplies which will be on a call out basis and which will be situated in eastern Canada.
  

• 
  The Operator reserves the right to contract alternative “best in class” services to compliment services provided by the Contractor. The Contractor will make available the necessary data to facilitate integration of alternate services.
  
• 
  Contractor shall provide an offshore team of qualified, experienced personnel to ensure 24-hour operational and maintenance capabilities. Contractor shall also provide qualified relief personnel to work on a rotational basis as per the Operator’s preferred schedule. The anticipated preferred offshore rotation is 21 days. All personnel will be required to have and maintain all training and certifications required for working offshore Canada/Newfoundland.
  

• 
  Contractor shall provide crew list containing the names, roles and experience of each crew member before commencement of operations for company approval.
  
• 
  Contractor shall not change Contractor’s Personnel from their designated positions without prior written approval from the Operator as per MOC procedure outlined in the Drilling and Completions Operations Manual (available for review upon request).
  

• 
  Contractor shall identify any reduction in personnel requirements associated with the utilization of more than one of the services identified in this Agreement.
  
• 
  The Operator reserves the right to reject any Contractor’s Personnel that the Operator considers unsuitable. The Contractor must provide qualified replacements at no additional cost to the Operator.
  
• 
  Contractor, where providing equipment and services sourced from a third party, shall clearly indicate these items and state the name of the third party vendor.
  
• 
  During the term of this Agreement the Contractor is encouraged to submit alternative proposals or specifications, in addition to that required by the Operator, where Contractor considers that such an alternative would be a technical, commercial, economic or operational improvement over the Operator’s original specification. Such alternative proposals shall be clearly identified and clearly indicate and justify all technical, commercial, economic or operational benefits over the specification required by Operator.
  

• 
  The Contractor shall provide a detailed description of the equipment that is proposed under this Agreement. Any additional items that are not identified in the proposal, but are necessary for the Contractor to conduct the Services, shall be provided free of charge.
  
• 
  The Contractor is responsible for performing Design Qualification testing ( DQT) to ensure that any component not previously used under these or more strenuous conditions is fit for purpose. Contractor shall review proposed equipment and provide a list of components that require design qualification testing.
  
• 
  The Contractor shall:
  

1. 
   complete a review and approval of quality plan for equipment and services to be provided.
   
2. 
   complete a review and approval of manufacturing and inspection /testing procedures where required
   
3. 
   submit a project specific “design of service” manual for the services and equipment for approval and review by Operator within 90 days of contract award.
   

• 
  The prices set forth in Schedule 2 - "Compensation for Services" will be applicable to any contract extension(s) subject to any pre-approved escalation of specific costs.
  

3. Husky Atlantic Region Well Overview

1. Applicable Fields

It is anticipated that these areas will be developed using four typical well types, though other designs may be possible in the future:

• 
  Horizontal Oil Production Wells
  
• 
  Deviated Gas Injection Wells
  
• 
  Deviated Water Injection Wells
  
• 
  Horizontal Water Injection Wells
  

2. Completion Fluid Composition

3. H2S

4. Well Ratings

Well Type	Tubing Size (mm)	Weight (kg/m)
Producer	139.7 x 177.8	25.3 x 38.7
Gas Injector	139.7	29.76
Water Injector	177.8	38.7

5. Rock Properties

Rock Property
Es – Static Young’s Moduli (GPa)	22
s – Static Poisson’s Ratio	0.18
p – Peak Friction Angle	50
Cp – Peak Cohesion (MPa)	13.5

Zone	UCS (MPa)
Gas	104
Oil	74
Oil-Water Transition	76
Water	114

Minimum Horizontal Stress	45.8 MPa
Maximum Horizontal Stress	47.0 MPa
Vertical Stress	65.0 MPa

The Contractor shall provide a statement of previous work experience, in close proximity to the Operating Area and over the last five years accompanied with the relevant reference contacts. If the Contractor has been dismissed from a job prior to conclusion of the contract, details of this dismissal should also be provided. Any work experience in offshore operations in eastern Canada should be Highlighted.

4. 
   
   Directory: downloads
   downloads -> Northern England’s set-jetting locations
   downloads -> Dynatest 3031 lwd light Weight Deflectometer
   downloads -> Forth coming competitive exams
   downloads -> Brush High School Morning Announcements Friday, September 05, 2014 all school
   downloads -> Year 9 The Arts — Music
   downloads -> Years 7 and 8 standard elaborations — Australian Curriculum: Music draft
   downloads -> Chris Young sets 2016 “I’m Comin’ Over” Tour headlining dates
   downloads -> Slavery and Abolition: the Plymouth Connection Introduction
   downloads -> Summer Assignment
   
   
   
   Download 215.99 Kb.
   
   Share with your friends: