Sip firmware Release 1 for ip phone 1140e administration

Download 1.47 Mb.

View original pdf

Page	39/76
Date	14.08.2023
Size	1.47 Mb.
	#61855

1 ... 35 36 37 38 39 40 41 42 ... 76

NN43113-300 02.05 1140E Adm

Length (1 octet) The Length value is variable. Count only the number of octets in the data field.Data (variable number of octets)
Procedure 4 Installing the IP Phone 1140E Step Action 1

Type (1 octet)
To avoid the possibility of option types already being used by different vendors, there are fourteen options types supported by the telephone. They are 128, 131, 144, 157, 188, 191, 205, 219, 223, 232, 247, 251, 247, and. Select one value from the type byte list for the DHCPOFFER response.
Nortel recommends using 232, 247, or 251. DHCP option numbers less than 224 are reclaimed by the IETF (RFC 3942). Future changes in the
DHCP protocol can force the telephone to stop sending these option requests. Currently, IP Phone E with SIP Firmware does support the remaining listed options to maintain backward compatibility.
Length (1 octet)
The Length value is variable. Count only the number of octets in the data field.
Data (variable number of octets)
ASCII based format VLAN-A:XXX+YYY+ZZZ. where, VLAN– A uniquely identifies this as the Nortel DHCP VLAN discovery request. Each VLAN ID
is followed by a plus (+) sign if there are more VLAN IDs or a period (.) to terminate the string.
There area maximum of 10 VLAN IDs that can be configured in the current version.
Once IP Phone E with SIP Firmware receives the DHCP offer containing the site-specific Voice VLAN option, the next DHCPDISCOVERY
message is tagged with the Voice VLAN ID.
SIP Firmware Release 1.1 for IP Phone E Administration
NN43113-300 Standard May Copyright © 2008, Nortel Networks

63
Physically install the IP Phone 1140E
Complete instructions to physically install the IP Phone E, including detailed figures and applicable warnings, are given in the document SIP
Firmware Release 1.1 for IP Phone E User Guide (NN43113-101).
The steps for installing the IP Phone E are summarized in the following procedure.
Procedure 4
Installing the IP Phone 1140E
Step
Action
1
Remove the stand cover. Pull upward on the center catch and remove the stand cover. The cable routing tracks are now accessible.
2
Connect the AC power adapter (optional. Connect the adapter to the AC adapter jack in the bottom of the IP Phone E. Form a small bend in the cable, and then thread the adapter cord through the channels in the stand.
3
Install the handset. Connect the end of the handset cable with the short straight section into the handset. Connect the end of the handset cable with the long straight section to the back of the IP
Phone E, using the RJ-9 handset jack. Form a small bend in the cable, and then thread the handset cord through the channels in the stand so that it exits behind the handset on the right side, in the handset cord exit in the stand base.
4
Install the headset (optional. If installing a headset, plug the connector into the RJ-9 headset jack on the back of the IP Phone
1140E, and thread the headset cord along with the handset cord through the channels in the stand, so that the headset cord exits the channel.
5
Install the Ethernet cable. Connect one end of the supplied Ethernet cable to the back of the IP Phone E using the RJ-45 connector and thread the network cable through the channel.
SIP Firmware Release 1.1 for IP Phone E Administration
NN43113-300 Standard May Copyright © 2008, Nortel Networks

Download 1.47 Mb.

Share with your friends:

1 ... 35 36 37 38 39 40 41 42 ... 76